Analog Signal Converter | 1 Channel | 18-30VDC | 450Hz | DIN Rail | Phoenix Contact | MCR-C-UI/UI-450-DCI | 2810887

MCR-C-UI-UI-450-DCI analogue signal converter and 3-way isolator – configurable U/I input and output, 18–30 V DC, 450 Hz, DIN rail, 2810887

MCR-C-UI-UI-450-DCI – a single-channel analogue signal converter and three-way galvanic isolator designed to electrically isolate, convert and transmit standard voltage and current signals to a control, measurement or automation system.

The input circuit, output circuit and power supply circuit are electrically isolated from one another. Integrated DC/DC converters provide 3-way isolation, helping to protect the control system against potential differences, ground loops and the adverse effects of interconnected sensor circuits.

This 450 Hz cut-off frequency version offers a response time of up to 0.8 ms and is suitable for transmitting faster-changing analogue signals.

The cut-off frequency of this version at the 3 dB level is 450 Hz. The specified 10–90% response time is approximately 0.8 ms.

• suitable for faster-changing analogue signals;
• faster response than the standard 30 Hz version;
• signals are transmitted using an inductive transmission principle;
• a filter installed after the transmission stage helps reduce interference;
• maximum transmission error – no more than 0.1% of full-scale value.

• ZERO adjustment – for signal zero-point correction within ±2%.
• SPAN adjustment – for full-scale measurement range correction within ±2%.
• DIP switches – for setting the input and output signal ranges.
• Green power LED indicator – indicates the auxiliary power supply status.

• Terminal 1 – voltage or current signal input IN U/I.
• Terminals 2 and 3 – input circuit GND 1.
• Terminal 7 – current output OUT I.
• Terminal 8 – voltage output OUT U.
• Terminal 9 – output circuit GND 2.
• Terminal 10 – +24 V DC power supply.
• Terminals 11 and 12 – power supply circuit GND 3.

• 3-way galvanic isolation – separates the input, output and power supply circuits.
• Configurable U/I signals – for different analogue voltage and current ranges.
• 450 Hz cut-off frequency – for faster-changing signals.
• 0.8 ms response time – for fast analogue signal transmission.
• ZERO and SPAN adjustment – for zero-point and range calibration.
• Green power LED – indicates the auxiliary voltage status.
• Removable screw terminals – for more convenient wire connection.
• 17.5 mm housing – for compact installation in an automation cabinet.
• DIN rail mounting – for standard control and automation cabinets.

• PLC and controller analogue inputs – to isolate and condition a sensor signal.
• Process automation – for pressure, temperature, level, flow and other process signals.
• Measurement systems – for isolating and converting analogue signals.
• Industrial control cabinets – to reduce the effects of ground loops and potential differences.
• Longer signal transmission lines – for signal transmission across higher circuit loads.
• Sensor circuits – to safely separate the sensor from the evaluation circuit.
• Test and laboratory equipment – for transforming analogue signals.
• Building and energy automation – for standard 0–10 V, 0–20 mA and 4–20 mA signals.

• Not all combinations of input and output ranges are permitted.
• Do not exceed an input voltage of 30 V or an input current of 50 mA.
• The voltage output load must be at least 10 kΩ.
• The current output load must not exceed 500 Ω.
• The IP20 housing is intended for installation inside a protected electrical or automation cabinet.
• Connection and configuration work must be performed by a qualified specialist.
• The ZERO and SPAN settings must be checked before commissioning the system.

Analogue signal conversion, 3-way isolation and 450 Hz transmission bandwidth

The MCR-C-UI-UI-450-DCI is a compact single-channel analogue signal converter that isolates the sensor, output and auxiliary power supply circuits. Three-way galvanic isolation helps protect the automation system against potential differences, ground loops and the effects of interconnected signal circuits.

Configurable voltage and current ranges allow the module to be adapted to a variety of analogue signal conversion tasks. The 450 Hz cut-off frequency and 0.8 ms response time allow faster-changing signals to be transmitted than with the standard 30 Hz version.

The 17.5 mm wide housing is mounted on a DIN rail, powered by 18–30 V DC and connected using removable screw terminals. The product is intended for industrial control, measurement and process automation systems requiring accurate analogue signal conversion and electrical circuit isolation.