Products catalog

  • Floor cable cover with adhesive tape | 3 channels | 30×10 mm | for cables up to Ø10 mm | flexible PVC | cuttable | 1 m | white

    Code: ES-TA03266914

    A low-profile floor cable cover made of soft PVC, designed to cover and protect cables running across the floor surface. The cover is 30 mm wide and 10 mm high, with three longitudinal channels inside for cables up to Ø10 mm. It is fixed to the floor with the adhesive tape on its underside – no drilling or screws.

  • Floor cable cover with adhesive tape | 3 channels | 30×10 mm | for cables up to Ø10 mm | flexible PVC | cuttable | 1 m | white

    A low-profile floor cable cover made of soft PVC, designed to cover and protect cables running across the floor surface. The cover is 30 mm wide and 10 mm high, with three longitudinal channels inside for cables up to Ø10 mm. It is fixed to the floor with the adhesive tape on its underside – no drilling or screws.

    Key point:
    A cable lying loose on the floor is both untidy and hazardous: people trip over it, office chair castors crush it and its insulation wears through. This cover tidies such cables in a few minutes. It is a practical solution wherever a cable cannot be hidden in the wall or under the floor covering.
    Dimensions
    30 × 10 mm
    Cable diameter
    up to Ø10 mm
    Number of channels
    3
    Fixing
    adhesive tape, no drilling

    How it works

    The cover has a semi-circular cross-section with bevelled edges. In the middle there is a 10 mm wide main channel, with two smaller channels on the sides. Cables are inserted from the underside, so they do not need to be disconnected from devices.

    Once the cables are in place, the protective film is removed and the cover is pressed onto a clean, dry floor surface. The flexible PVC adapts to minor surface irregularities, and the bevelled profile lets people walk over it and chair castors roll across without catching.

    The cover is easily cut with a knife or scissors, so its length can be matched to the route without waste.

    Why choose this floor cable cover?
    A cable lying on the floor becomes a tidy, safe route. No tools, no installer and no need to remove the floor covering.

    Technical specifications

    Product type Floor cable cover (cable protector)
    Code ES-TA03266914
    Material Soft, flexible PVC
    Width 30 mm
    Height 10 mm
    Number of channels 3 (10 mm wide central + 2 side channels)
    Max. cable diameter Ø10 mm (in the central channel)
    Indicative capacity 2 thicker extension cords or 3 Ethernet cables
    Cable insertion From the underside
    Fixing Integrated adhesive tape to the floor
    Length 1 m
    Cutting With a knife or scissors to the required length
    Colour White
    Place of use Indoors

    Main features

    • Three separate channels – power and data cables can run along one route without being mixed.
    • Low 10 mm profile with bevelled edges – reduces the risk of tripping over the cable.
    • Adhesive tape – the cover is fixed without drilling and does not damage the floor covering.
    • Insertion from below – cables do not need to be disconnected from devices.
    • Flexible PVC – adapts to the floor and is easily cut to the route.
    • Mechanical protection – protects cables from abrasion, foot traffic and office chair castors.

    Where is it used?

    • Office workstations with the desk in the middle of the room
    • Living room: TV, audio system or router cables across the floor
    • Home office and computer area
    • Meeting and conference rooms
    • Exhibition stands and temporary workstations
    • Shop checkouts, reception desks, sales areas
    • Temporary cables during renovation or fit-out

    Use by need

    For home users.
    An extension or internet cable can be run neatly across the room without drilling or damaging the floor.
    For office administrators.
    A workstation in the middle of a room can be connected in minutes, removing the tripping hazard in walkways.
    For event and exhibition installers.
    A quick way to cover cables on temporary stands where visitors walk.

    Practical use

    For example, a desk stands 3 m from the wall socket with a walkway in between. In that case 3 pcs of this cover are enough: the extension cord runs in the central channel and an Ethernet cable in a side channel. The covers are stuck across the walkway, and the cable no longer gets in the way.

    Pros

    • 3 channels to separate power and data cables
    • Low 10 mm profile, less tripping
    • Installed without tools or drilling
    • Cables inserted from below, no need to disconnect them
    • Cut to the required length
    • White colour matches light floors

    Cons / limitations

    • Suitable for cables up to Ø10 mm; thicker cables need a wider cover
    • Designed for foot traffic and office chairs, not for forklifts or vehicles
    • Adhesive tape holds poorly on carpet, dusty or damp surfaces
    • Intended for indoor use

    Safety and installation notes

    • Clean and dry the floor before sticking – adhesion depends on it.
    • The cover is supplied coiled. If it does not lie flat, roll it in the opposite direction for a few minutes before installation.
    • Do not place damaged cables or cables with joints or terminals inside the cover.
    • The cover covers and protects the cable but does not replace its insulation. Do not overload the extension cord beyond its rated current.
    • Adhesive residue may remain on some floor coverings when the cover is removed. Test in an inconspicuous spot first.

    Quick selection guide

    30 × 10 mm
    Cable up to Ø10 mm
    3 channels
    Adhesive tape | indoors
    Suitable when you need:
    • to run a cable across a walkway or the middle of a room
    • quick installation without drilling
    • a temporary or permanent solution at the office or at home
    Check before use:
    • diameter of the thickest cable (≤ 10 mm)
    • the floor covering (hard, smooth surface)
    • the required route length in metres
    Important reminder: this cover does not replace heavy-duty rubber cable protectors designed for vehicle or forklift traffic.

    FAQ

    How thick a cable fits?
    The central channel takes a cable up to Ø10 mm, e.g. an extension cord.
    Can several cables be routed?
    Yes, the cover has 3 separate channels, e.g. for 2 thicker cords or 3 Ethernet cables.
    Do I need to disconnect the cable from the device?
    No, cables are inserted from the underside of the cover.
    Can it be stuck on carpet?
    Not recommended – the adhesive tape holds reliably only on hard, smooth and clean surfaces.
    How do I make a longer route?
    Order the required number of metres and lay the pieces end to end.
    Is it suitable outdoors?
    No, the cover is intended for indoor use.

    Floor cable cover with adhesive tape | 30×10 mm | white

    Flexible PVC floor cable cover with three channels for cables up to Ø10 mm. It is fixed with adhesive tape, so cables can be run neatly and safely across an office or home without drilling.

    Published: 2026-11-06 · Data verified against the manufacturer's specification: 2026-11-06

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Protective flexible spiral cable wrap for wires and cables | Ø20 mm | 2.5 m | Brennenstuhl Spiralschlauch | 1164360 | 4007123562381
    Code: 1164360

    Flexible and easy-to-install protective spiral sleeve for wires and cables, designed for neat cable grouping and protection against tangling, mechanical abrasion, and messy cable placement in work or home environments.

    This Ø20 mm, 2.5 m long cable protection sleeve is especially suitable where several cables are used in one place: near a computer desk, TV area, office equipment, workshop equipment, electrical appliances, or temporary cable management systems. The spiral design allows cables to be conveniently wrapped without dismantling the existing installation – the sleeve can be wound directly onto already connected cables. 

    Price 9.68 € VAT incl.
    ( 8.00 € VAT excl. )
    Installation cable trunking | self-adhesive | cuttable | 10x10mm | 5m | white | Rosi | 71501-A | 8050040701933
    Code: 71501-A

    Installation cable trunking designed to neatly hide and protect wires at home, in the office, workplace, or commercial premises. Thanks to its compact 10x10 mm size, the trunking is suitable for thin wires, internet cables, TV, modem, computer, LED lighting, or other low-voltage device cables.

    The trunking is supplied in a 5-meter roll, so it can be easily cut to the required length. The white design allows the trunking to be discreetly matched with walls, skirting boards, furniture, or other light-colored surfaces. 

    Price 24.99 € VAT incl.
    ( 20.65 € VAT excl. )
    Flexible copper cable H03VV-F | 2×0.5 mm² | 300/300 V | round | white | 1 m | Lietkabelis
    Code: 91525001

    H03VV-F 2×0.5 mm² – AB Lietkabelis flexible round copper cable with class 5 conductors, PVC insulation and a white PVC sheath, 300/300 V. Sold by the metre.

    Cores: L and N, no PE. Indicative current ≈ 3 A – for light appliances indoors.

    Price 0.30 € VAT incl.
    ( 0.25 € VAT excl. )
  • Subscribtion to new arrivals

    privacy policy

    Information