Dielectric rubber mat for electricians | 750x750x7mm | 1000V | with inspection certificate | brown

Dielectric rubber mat for electricians – 750 x 750 x 7 mm, up to 1000V, with inspection and EN 61111:2009 certificate

Dielectric rubber mat is intended as additional protection for electricians working near electrical equipment, distribution boards, control cabinets and other areas where there may be a risk of electric shock. The mat is 750 x 750 mm in size, 7 mm thick, brown in colour and supplied with a CE EN 61111:2009 certificate, user manual and valid inspection document.

• Additional electrical insulation – used in front of electrical panels and equipment.
• Protection when working near electrical equipment – helps reduce the risk of electric shock when safe working requirements are followed.
• Inspected product – each mat is supplied with an inspection document.
• EN 61111:2009 certificate – supplied together with the product.
• 20 kV test voltage – the product has been tested according to the specified parameters.
• Compact 750 x 750 mm size – convenient for use near panels, cabinets and control equipment.
• 7 mm thickness – stronger and reliable rubber construction.
• Operating temperature from -15°C to +40°C – suitable for many indoor and technical room conditions.

• Near electrical panels – during connection, inspection or maintenance work.
• Near distribution cabinets – in electrical equipment control and service areas.
• In manufacturing companies – near motor control cabinets, automated lines and technical panels.
• In transformer stations and electrical rooms – according to site safety procedures and usage conditions.
• In workshops and technical rooms – near electrical inputs, control equipment and distribution points.
• In commercial and residential buildings – for electrical cabinet maintenance work when additional insulating protection is required.

For example, before starting maintenance or measurement work near a distribution cabinet, an electrician places the dielectric mat on a clean, dry and level floor surface. During work, the employee stands on the mat, using additional insulating protection from earth potential.

Before use, the mat must be inspected: check for cuts, cracks, heavy wear marks, oil, chemicals, moisture or other damage. A damaged mat or a mat with expired inspection documentation must not be used until its condition has been assessed according to applicable safety procedures.

For an electrician: a practical additional protective measure when carrying out installation, inspection and maintenance work on electrical panels, automation cabinets, distribution equipment and other electrical systems.

For an industrial maintenance specialist: suitable for use near production equipment panels, motor control cabinets, automated lines and other electrical equipment where periodic service work is performed.

For a person responsible for electrical maintenance: can be used as part of the site electrical safety equipment set in transformer stations, technical rooms, warehouses and administrative buildings.

For a contractor: convenient to have a separate inspected mat when carrying out electrical work at customer sites, where not only protection but also documentation is important – certificate, instructions and valid inspection.

The dielectric mat is an additional electrical safety measure. It cannot replace mandatory safe working procedures, disconnection of electrical equipment, verification of absence of voltage, earthing and other required protective measures.

• Use only for its intended purpose and according to the supplied instructions.
• Inspect the surface of the mat before each use.
• Do not use the mat if it is cracked, cut, heavily contaminated, wet or otherwise damaged.
• Place the mat only on a clean, dry and level surface.
• Follow the recommended operating temperature from -15°C to +40°C.
• After the inspection document expires, follow the site electrical safety procedure.
• Work on electrical equipment must be carried out only by qualified personnel.
• Before work, all necessary electrical safety procedures must be applied.

Quick selection guide

Choose the dielectric rubber mat 750 x 750 x 7 mm when an additional insulating measure is required for an electrician working near low-voltage electrical equipment up to 1000V. This version is supplied already inspected, so there is no need to order additional test documents.

Inspected dielectric mat for safer work near electrical equipment

The dielectric rubber mat 750 x 750 x 7 mm is a practical additional safety measure for electricians, maintenance specialists and contractors performing work near electrical panels, distribution cabinets and other electrical equipment.

Thanks to the operating voltage up to 1000V, 20 kV test voltage, EN 61111:2009 certificate, included instructions and 12-month valid inspection document, this mat is ready for use as an additional electrical safety measure according to site requirements.