Differential pressure relay 0,2-5mbar | 10A | 115-277VAC
Code: ESLF35-2Price 31.15 € VAT incl.( 25.74 € VAT excl. )Differential air pressure switch 0.2–5 mbar, SPDT 10 A, −40…+82 °C. For fan, filter and burner airflow monitoring.
-
Differential pressure relay 0,2-5mbar | 10A | 115-277VAC
Differential pressure switch for air with a setting range of 0.2–5 mbar. It proves airflow in ducts, monitors filter clogging and fan operation: when the pressure difference reaches the set point, the SPDT contact changes over and signals the controls or opens the circuit.
Key idea:
Ventilation and combustion systems need a clear yes/no signal: is the fan really running, is the filter still clean. This switch checks it without electronics, and the 10 A contact allows direct connection to the control circuit.Setting range
0.2–5 mbarContact
SPDT, 10 A, 115–277 V ACMax. pressure
30 mbarOperating temp.
−40…+82 °COperating principle
The switch is mounted on a wall or duct with the diaphragm in any vertical plane. Pressure ports are connected to the measuring points with 0.25" tubing or flexible hoses.
The pressure difference acts on the diaphragm; when the set point is reached, the microswitch changes over. The switching differential increases progressively: ≈0.05…0.25 mbar from minimum to maximum setting.
The result is a reliable signal for the controls: fan running confirmation, filter alarm or burner airflow monitoring.
Why choose the LF35 differential pressure switch?
The metal construction, wide operating temperature range and 10 A contact allow use in demanding locations – outdoor units or near burners.Technical specifications
Product type Differential air pressure switch (diaphragm, SPDT) Manufacturer / series LEFOO / LF35 Setting range 0.2–5 mbar Switching differential ≈0.05…0.25 mbar (progressive) Maximum pressure 30 mbar Medium air Measured pressure positive, negative or differential Contact SPDT Electrical rating 10 A non-inductive, 277 V AC; 300 VA pilot duty 115–277 V AC Operating temperature −40…+82 °C Connections 0.25" OD compression fittings for tubing or 0.25" slip-on connectors for hose Mounting position diaphragm in any vertical plane Main functions
- Airflow proving – the controls know the fan is really running.
- Filter clogging alarm – a signal when resistance exceeds the limit.
- SPDT contact 10 A – direct connection to the control circuit.
- Positive, negative and differential pressure – flexible connection.
- Wide temperature range – −40…+82 °C.
Where is it used?
- Fan operation monitoring in air handling units
- Filter clogging alarms
- Burner and boiler airflow monitoring
- Airflow monitoring in ducts and pipes
- Tunnel and shaft ventilation
- Building energy management systems
Use by need
For ventilation controls installers.
Simple fan running confirmation without extra transmitters.For boiler / burner service.
Airflow monitoring for the combustion safety circuit.For facility managers.
Automatic signal when to replace a filter.Practical application
If an air handling unit filter should be replaced when its resistance reaches ~2 mbar (200 Pa), choose a range that covers this value, connect “+” before the filter and “−” after it, and set the limit to 2 mbar – the contact will give an alarm when it is reached.Pros
- Robust metal construction
- 10 A SPDT contact
- Wide temperature range −40…+82 °C
- For positive, negative and differential pressure
- No power supply needed
Cons / limitations
- Does not output a pressure value – a pressure transmitter is needed for that
- Air only – not for liquids
- Limited maximum pressure – 30 mbar
- Manual setting, no display
Safety and installation notes
- Make electrical connections only with the voltage disconnected.
- Do not exceed 30 mbar or the contact current.
- Mount the diaphragm in a vertical plane.
- Fit hoses tightly to avoid leaks.
- After setting, verify switching under real conditions.
Quick selection guide
Range 0.2–5 mbarSPDT 10 AAir−40…+82 °CSuitable when you need:- to confirm fan operation
- a filter clogging alarm
- burner airflow monitoring
Check before use:- the required set point is within the range
- the pressure will not exceed 30 mbar
- the control circuit matches the contact rating
Important reminder: the switch only signals a pressure limit – it does not replace combustion safety controls where standards require them.FAQ
What is this switch for?
For airflow and filter clogging monitoring in ventilation and combustion systems.Can it measure vacuum?
Yes, it works with positive, negative and differential pressure.Does it need power?
No, the switch works mechanically.What is the contact rating?
10 A non-inductive load, 115–277 V AC.Is it suitable for water?
No, it is for air only.How should it be mounted?
With the diaphragm in any vertical plane.Differential pressure relay 0,2-5mbar | 10A | 115-277VAC
LEFOO LF35 differential air pressure switch 0.2–5 mbar, SPDT 10 A – for fan operation, filter clogging and burner airflow monitoring.
Published: 2026-11-16 · Data verified against the manufacturer's datasheet: 2026-11-16
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.This product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products














