Products catalog

  • Digital cyclic (twin) time relay | 0.1 s – 990 h | LED display | 8-pin socket | 220 V AC | OURTOP DH48S-S

    Code: DH48S-S

    Digital twin time relay that repeatedly switches its output on and off according to two separately set times.

  • Digital cyclic (twin) time relay | 0.1 s – 990 h | LED display | 8-pin socket | 220 V AC | OURTOP DH48S-S

    Digital twin time relay that repeatedly switches its output on and off according to two separately set times. Times are set with buttons from 0.1 s to 990 h, progress is shown on the LED display; the relay plugs into a standard 8-pin socket.

    Key point:
    When a cycle must be precise and visible, the digital twin relay shows the countdown on an LED display and allows times from 0.1 s to 990 h. It plugs into a standard 8-pin socket, so it easily replaces old mechanical relays.
    Time range
    0,1 s – 990 h
    Function
    two-time cycle
    Supply voltage
    220 V AC
    Mounting
    8-pin socket

    Operating principle

    The relay plugs into an 8-pin socket (e.g. PF083A) on a DIN rail or mounts in the panel door; supply is 220 V AC.

    Two separate times – on and off – are set with the buttons from 0.1 s to 990 h, and the relay repeats them alternately.

    The LED display shows progress, so the operator immediately sees how long until the next switching.

    Why choose DH48S-S?
    Digital setting without knob error and a very wide 0.1 s – 990 h range – one model suits cycles from seconds to several days.

    Technical specifications

    Product typeDigital cyclic time relay
    Manufacturer / modelOURTOP DH48S-S
    Supply voltage220 V AC
    Time range0,1 s – 990 h
    FunctionRepeat on/off cycle (two times)
    DisplayLED
    Mounting8-pin socket (e.g. PF083A), panel door

    Key functions

    • Twin cycle – separate on and off times.
    • Range 0.1 s – 990 h – from short pulses to long pauses.
    • LED display – progress and settings visible.
    • 8-pin socket – quick replacement without rewiring.
    • Door or DIN mounting – flexible layout.

    Where is it used?

    • Fan, pump and compressor cycles
    • Machine tool and production line automation
    • Signalling and periodic processes
    • Replacing old mechanical time relays
    • Control desks with time indication in the door
    • Agricultural and greenhouse equipment

    Use by need

    For the automation engineer.
    Precise cycles from 0.1 s with visible progress – easy to tune and check.
    For the service technician.
    Replaced by plugging into the existing 8-pin socket – minimal downtime.
    For the production foreman.
    The operator sees on the display how long until switching.

    Practical example

    If a compressor must run for 40 min and rest for 20 min, DH48S-S with two set times repeats this cycle automatically, and the LED display shows how long until the next switching.

    Advantages

    • Wide range 0.1 s – 990 h
    • Precise digital setting
    • LED display with progress
    • Standard 8-pin socket
    • Door or DIN mounting

    Limitations

    • The socket (e.g. PF083A) is sold separately
    • Supply 220 V AC only
    • Check the contact rating on the housing diagram; use a contactor for larger loads
    • No overload or short-circuit protection – a circuit breaker is required

    Safety and installation notes

    • Install only with the power disconnected; work in the panel must be done by a qualified electrician.
    • Plug the relay in and out only with the power off.
    • Wire the socket pins according to the diagram on the relay housing.
    • Use an intermediate contactor for motors and high-inrush loads.

    Quick selection guide

    0,1 s – 990 h
    220 V AC
    LED
    8-pin
    Suitable when you need:
    • A precise repeating cycle with two times
    • Visible timing on the panel door
    • Replace an old relay in an 8-pin socket
    Check before use:
    • Supply voltage is 220 V AC
    • That you have a suitable 8-pin socket
    • That the load current matches the contact rating
    Important: DH48S-S controls the cycle by time but is not a protective device and does not replace a circuit breaker or motor protection.

    FAQ

    What is the time range?
    From 0.1 s to 990 h for both times.
    Is the socket included?
    No, the 8-pin socket (e.g. PF083A) must be bought separately.
    What is the supply voltage?
    220 V AC.
    How are the times set?
    With the front buttons, and the values appear on the LED display.
    Where can it be mounted?
    In a socket on a DIN rail or in the panel door.
    Can it switch a motor directly?
    Use an intermediate contactor for motors and larger loads.

    Digital cyclic (twin) time relay | 0.1 s – 990 h | LED display | 8-pin socket | 220 V AC | OURTOP DH48S-S

    DH48S-S is a digital twin (cycle) time relay with two times from 0.1 s to 990 h, LED display and 8-pin socket, 220 V AC. Suitable for fan, pump, compressor and production process cycles.

    Published: 2026-11-19 · Data verified against the manufacturer specification: 2026-11-19

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • privacy policy

    Information