Products catalog

Home/Product Catalog/HVAC control solutions for heating and ventilation/HVAC automation/Speed regulators for fans/Electronic speed controllers for fans
  • New item   -45.25€EBM-Papst FFU filter unit fan controller | Sentera Controls | SPVL8-010-EP
    New item   -45.25€EBM-Papst FFU filter unit fan controller | Sentera Controls | SPVL8-010-EP 1
    New item   -45.25€EBM-Papst FFU filter unit fan controller | Sentera Controls | SPVL8-010-EP 2
    New item   -45.25€EBM-Papst FFU filter unit fan controller | Sentera Controls | SPVL8-010-EP 3
    New item   -45.25€EBM-Papst FFU filter unit fan controller | Sentera Controls | SPVL8-010-EP 4
    New item   -45.25€EBM-Papst FFU filter unit fan controller | Sentera Controls | SPVL8-010-EP 5

    EBM-Papst FFU filter unit fan controller | Sentera Controls | SPVL8-010-EP

    Code: SPVL8-010-EP
    Inquire about this item
    Price 80.82 € VAT incl.
    ( 66.79 € VAT excl. )
    126.07 € You save 45.25 €
    Offer is valid until 2026-12-31
    Want another price? Suggest yours!
  • Product description

    EBM-Papst FFU filter unit fan controller | Sentera Controls | SPVL8-010-EP

    SPVL8-010-EP – Sentera Controls EC fan controller with Modbus / DCI output, designed for EBM-Papst fan filter units (FFU) with EC motors, including the K3G series with a Modbus / DCI interface. One controller configures, controls and monitors up to 20 fans.

    Key idea:
    Instead of an analogue signal for each fan – a single digital chain: the controller detects the connected FFUs itself, assigns them network IDs, and the RGB LED shows whether all fans are running without errors.
    Power supply
    85–305 VAC, 50–60 Hz
    Output
    Modbus / DCI (EBM-Papst)
    Number of fans
    up to 20
    Protection
    IP44 / IP54

    Operating principle

    The controller is supplied from the mains, and EBM-Papst FFU fans are daisy-chained with Cat5 / UTP cable with RJ45 connectors (RS485 + DCI). During commissioning each fan is automatically configured and receives a network ID.

    This is not a power controller: the motor supply is connected separately, and SPVL8-010-EP only sends digital speed commands and reads the status.

    The knob changes the speed of all fans steplessly from 10 % to 100 % (or vice versa), the end position is OFF. Vmin, Vmax and direction are set via Modbus RTU holding registers.

    Engineer's note: the RGB LED shows whether the installation is OK, whether configuration is needed, whether any motor is not responding, or whether there are warnings or errors – this greatly shortens cleanroom commissioning work.

    Benefits SPVL8-010-EP?
    Up to 20 FFU fans are started, controlled and monitored by a single device without a separate controller or programming for each fan.

    Technical specifications

    Product type EC fan controller with Modbus / DCI output
    Manufacturer / code Sentera Controls / SPVL8-010-EP
    Suitable fans EBM-Papst FFU with EC motors and Modbus / DCI interface (including the K3G series)
    Supply voltage 85–305 VAC, 50–60 Hz
    Output Modbus / DCI (daisy-chain connection)
    Number of fans Up to 20
    Control range 10–100 %, OFF position
    Settings Vmin, Vmax, direction – via Modbus RTU holding registers
    Status indication RGB LED and Modbus input registers
    Connections Supply 0.5–1.5 mm²; fans – Cat5 / UTP, RJ45 (RS485 + DCI)
    Installation Flush-mounted (IP44) or surface-mounted (IP54)
    Protection class IP44 / IP54 (EN 60529)
    Operating environment 0–40 °C, 5–95 % rH non-condensing
    Weight 0.153 kg (net)
    Compliance LVD 2014/35/EU, EMC 2014/30/EU, RoHS 2011/65/EU

    Manufacturer documentation

    ✔ Recommended by Elektrotechnikos sprendimai

    Original manufacturer documentation – technical data, wiring diagrams and installation instructions.

    Main functions

    • Automatic configuration – each fan is configured and receives a network ID automatically.
    • Up to 20 fans – a single Modbus / DCI chain.
    • Status monitoring – RGB LED and Modbus input registers: non-responding motors, warnings, errors.
    • OFF position – all fans are stopped with the knob.
    • Bootloader – firmware updates via Modbus RTU.

    Where is it used?

    • Cleanrooms with FFU ceilings
    • Production areas in the pharmaceutical, electronics and food industries
    • Laboratories and operating theatres with EBM-Papst FFU
    • Modernisation of existing FFU systems

    On-demand operation

    For the cleanroom installer.
    Automatic ID and configuration – quick commissioning.
    For the maintenance engineer.
    RGB indication immediately shows a non-responding fan or an error.
    For the facility manager.
    All FFUs are controlled with a single knob.

    Application guide: how it is used in practice

    SPVL8-010-EP can be adapted to different FFU systems – only the number of fans and the connection method change:

    Site What is connected Result Installer's note
    Cleanroom ceilings with FFUs Up to 20 EBM-Papst FFU → Modbus / DCI chain (RJ45) All filter units run at the same speed Use Cat5 / UTP cable
    Laboratory FFU with K3G fans → Modbus / DCI Speed is changed with the knob according to the operating mode Set Vmin according to the min. airflow for the cleanliness class
    FFU system commissioning Newly connected fans → automatic configuration IDs are assigned automatically Watch the RGB LED: flashing – configuration required
    System with BMS Modbus RTU registers Status and errors are visible centrally Register list – in the Sentera Modbus register table

    How to select the controller current

    Rated current of the motor(s) Recommended model
    OFF and Modbus RTU needed, one EC fan SPV-8-010-PM (OFF, Modbus RTU)
    Dry contact (4 A) and Modbus RTU needed SPV-8-010-CP (dry contact 4 A, Modbus RTU)
    Control of several EC fans with one signal needed SPV-8-010-MF (0-10 VDC, RL ≥ 1 kΩ, dry contact 4 A)
    EBM-Papst FFU control via Modbus / DCI needed (up to 20 pcs) SPVL8-010-EP (Modbus / DCI, up to 20 fans) ← this model
    Rule: SPVL8-010-EP is suitable only for fans with an EBM-Papst Modbus / DCI interface; up to 20 fans per controller. For fans with an analogue 0-10 V input choose SPV-8-010-MF or SPV-8-010-PM.
    When to choose another solution: for EC fans controlled by an analogue 0-10 VDC signal – SPV-8 series (PM / CP / MF); with a display – RDCV9-AD.

    Pros

    • Up to 20 FFU fans
    • Automatic configuration and ID assignment
    • Status and error indication via RGB LED
    • OFF position
    • Supply 85–305 VAC

    Cons / limitations

    • Suitable only for fans with an EBM-Papst Modbus / DCI interface
    • More than 20 fans – several controllers are required
    • Operating temperature 0–40 °C
    • No contacts or alarm outputs are specified in the datasheet

    Safety and installation notes

    • Installation and connection must be carried out by a qualified electrician with the supply to all connected devices disconnected.
    • The terminals carry mains voltage – connect only with the supply disconnected.
    • Do not connect terminals 4 and 5.
    • Use Cat5 / UTP cable with RJ45 connectors for the fan chain.
    • Use at 0–40 °C, 5–95 % rH non-condensing.

    Quick selection guide

    EBM-Papst FFU
    Modbus / DCI
    up to 20 fans
    85–305 VAC
    IP44 / IP54
    Suitable when you need:
    • control up to 20 EBM-Papst FFU fans with a single knob;
    • automatically start up and configure FFUs;
    • monitor fan status and errors.
    Check before use:
    • whether the fans have an EBM-Papst Modbus / DCI interface;
    • the number of fans (≤ 20);
    • a Cat5 / UTP cable route.
    Important reminder: SPVL8-010-EP is a digital control and monitoring device, not a power controller; the fan supply is connected separately.

    FAQ

    How many fans can be connected?
    Up to 20.
    Is it suitable for EC fans from other manufacturers?
    No – it is designed for EBM-Papst fans with a Modbus / DCI interface.
    How are addresses assigned?
    Automatically – the controller itself assigns a network ID to each fan.
    How do I find out about a fault?
    The RGB LED shows non-responding motors, warnings and errors; the same information can be read via Modbus RTU.

    EBM-Papst FFU filter unit fan controller | Sentera Controls | SPVL8-010-EP

    Sentera SPVL8-010-EP – EC fan controller for EBM-Papst FFU filter units with Modbus / DCI: up to 20 fans, automatic configuration, RGB status indication, 85–305 VAC, IP44 / IP54.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • privacy policy

    Information