Electric towel warmer | heated towel rail | with timer | 300W | 230V | IP44 | 500x800mm | black | ADAX Wave 50-80-300 BLACK

Electric towel warmer | heated towel rail | 300 W | 500 × 800 mm | 7 bars | IP44 | black RAL 9035 | ADAX Wave 50-80-300 Black

ADAX Wave 50-80-300 Black is a black electric ladder-type heated towel rail designed for drying and warming towels and providing additional bathroom comfort. The model features 7 rectangular-profile bars, a 300 W electric heating element, a programmable MUSA controller, temperature adjustment from 7–30 °C and an IP44 protection rating. The black RAL 9035 finish and understated Scandinavian design suit both modern and classic bathroom interiors.

ADAX Wave 50-80-300 Black combines towel drying, electric heating and programmable temperature control in one appliance. The integrated MUSA controller provides COMFORT, NIGHT, ANTIFREEZE, TIMER-2H and CHRONO modes, allows heating to be programmed by day of the week and hour, and includes open-window detection and button-lock functions.

Ready to use: the towel warmer is already filled with heat-transfer fluid and equipped with a programmable electric heating element, so after mechanical installation it only needs to be correctly connected to the electrical supply.

Unlike ladder designs with round profiles, ADAX Wave uses rectangular-profile black steel tube bars. The model has 7 horizontal bars, providing space for everyday towels. Its 500 × 800 mm dimensions allow the towel warmer to be practically integrated even where bathroom wall space is limited.

The installed black electric heating element is rotatable. This allows the towel warmer to be adapted during installation so that the controller is positioned on the more convenient side – a right-hand or left-hand installation configuration can be selected.

The appliance is switched on or placed in standby mode using the [On/Standby] button.

• When the appliance is switched on, the display shows the current time, selected mode and set temperature.
• In standby mode, the current time, day of the week and [Stb] message are displayed.
• When switching to standby mode, the appliance emits two 0.5-second beeps.
• When switching the appliance on, one approximately 1-second audible signal is heard.

Two main temperature levels can be set in the controller:

• COMFORT temperature is used in COMFORT, CHRONO and, where applicable, FIL-PILOT modes.
• NIGHT temperature is used in NIGHT and CHRONO modes.
• The overall configurable temperature range is 7–30 °C.
• The NIGHT temperature must be at least 0.5 °C lower than the COMFORT temperature.

In COMFORT mode, the towel warmer steadily maintains the selected room temperature. The mode is selected by pressing [Prog] until the COMFORT icon appears on the display, while the desired temperature is set using [+] and [−].

NIGHT mode maintains a lower temperature than COMFORT mode. It is recommended for night-time or when the room will not be used for 2 hours or more. The NIGHT temperature can be adjusted from 7 °C up to the COMFORT temperature minus 0.5 °C.

In ANTIFREEZE mode, the setting is fixed at 7 °C. The heating element is activated when the room temperature falls below this level. This mode is useful during holidays, in guest rooms or other infrequently used spaces.

TIMER-2H mode is intended for faster drying of damp towels or temporarily providing more intensive room heating. When this mode is selected, the appliance operates at the maximum 300 W power for up to 2 hours, up to a maximum room temperature of 30 °C. When the set time expires, the appliance automatically returns to the previously used mode.

CHRONO mode allows an individual 7-day heating schedule to be created. Each hour of every day of the week can be assigned:

• COMFORT temperature – shown on the display as a filled time bar.
• NIGHT temperature – shown on the display as an empty time bar.

This allows the temperature to be reduced automatically at night or when the bathroom is not in use and returned to the comfort temperature before the expected time of use.

1. Switch the appliance to STANDBY mode.
2. Press and hold [−] for at least 3 seconds.
3. [SEt] appears at the top of the display.
4. Use [+] to select [tEd].
5. Press [Prog] and set the day of the week.
6. Confirm the day using [Prog].
7. Use [+] and [−] to set the hours and confirm with [Prog].
8. Set the minutes in the same way.
9. At the end of the procedure, the controller returns to STANDBY mode.

1. Switch the appliance to STANDBY mode.
2. Hold [−] for at least 3 seconds until [SEt] appears on the display.
3. Use [+] to select [Pro9].
4. Press [Prog] to enter programming mode.
5. For each hour of the day, use [+] to assign COMFORT and [−] to assign NIGHT temperature.
6. Press [Prog] to confirm the first day's programme.
7. Repeat the procedure for the remaining 6 days of the week.

The open-window detection function responds to a sudden drop in room temperature. When such a change is detected, the heating element is temporarily switched off. Heating resumes when the rise in temperature indicates that the window has been closed.

The function can be activated or disabled in the controller settings. When the function is active, the Open Window icon is displayed.

Note: an open window may not be detected if the thermostat is located in an isolated area of the room, far from air currents, close to an external heat source, or if the room temperature decreases very slowly.

To prevent accidental changes to temperature or programmes, the control buttons can be locked. Holding [Prog] for approximately 3 seconds locks all buttons except [On/Standby]. A lock symbol appears on the display. To unlock, hold [Prog] again for approximately 3 seconds.

FIL-PILOT mode applies only to products equipped with the Fil-Pilote system. In this case, the towel warmer's operating mode can be controlled by a central building or home heating-control system. Fil-Pilote compatibility of the specific product must be checked according to its configuration.

• Bathrooms.
• Drying and warming towels.
• Additional bathroom heating.
• Sanitary rooms in apartments and residential houses.
• Hotel and guest-house bathrooms.
• Smaller and medium-sized spaces where compact 500 × 800 mm dimensions are important.
• Modern, minimalist bathroom interiors and interiors with dark accents.
• Rooms where programmable electric heating is required.

1. Always disconnect the electrical supply before installation or electrical connection work.
2. Install the towel warmer vertically on a suitable and sufficiently strong wall.
3. Use fixing screws suitable for the specific wall construction.
4. The appliance must not be installed with the electrical controller at the top.
5. It is recommended to install the lowest heated bar no lower than 600 mm above the floor.
6. It is recommended to leave at least 50 cm of free space in front of the appliance.
7. Objects should not be placed closer than 10 cm to the towel warmer.
8. The heating appliance must not be installed directly below an electrical socket.
9. The appliance must not be exposed to intense or prolonged moisture.
10. Installation and electrical work must be carried out by a qualified person in accordance with applicable requirements.

The towel warmer has an IP44 protection rating and is protected against splashing water. It may be installed in bathroom zone 2 if the electrical controls cannot be reached by a person using the bath or shower.

Electrical safety: in rooms containing a bath or shower, the electrical supply circuit must be protected by a suitable residual-current device with a rated residual current not exceeding 30 mA, where required by the applicable installation regulations.

• Switch off the appliance and allow it to cool before cleaning.
• Use cold or lukewarm water for cleaning – no warmer than 25 °C.
• Use a soft, non-abrasive cloth or wipe.
• A neutral or mildly alkaline cleaner may be used for stubborn stains.
• Avoid intensive rubbing and scrubbing.
• Do not use scraping tools, abrasive sponges or rough materials.
• Do not use acidic or strongly alkaline cleaners.
• Do not use steam cleaners.
• Do not use aggressive organic solvents.
• Do not use cleaning products with an unknown chemical composition.
• After cleaning, immediately rinse the surface with clean cold water to remove all cleaning-product residues.

• The specified maximum temperature of accessible surfaces is 80 °C.
• Some parts of the appliance may become very hot during operation.
• The towel warmer is intended for drying towels but must not be completely covered.
• Completely covering the appliance may increase its temperature and activate internal protection.
• Do not sit on the appliance or use it as a chair, support, ladder or toy.
• Special attention is required when small children or vulnerable persons are nearby.
• Children must not play with the appliance.
• A damaged power cable or electrical controller must be replaced by a qualified person.
• The power supply must be disconnected before maintenance work.
• The appliance is not intended for use at altitudes above 2000 m.

Power failure: CHRONO mode information – current day, time and daily programme – is retained in memory for several minutes.

ADAX Wave 50-80-300 Black | electric towel warmer | heated towel rail | 300 W | 500 × 800 mm | 7 bars | IP44 | black RAL 9035

ADAX Wave 50-80-300 Black is a black RAL 9035 electric ladder-type towel warmer with a rated power of 300 W and dimensions of 500 × 800 mm. The model has 7 rectangular-profile bars, IP44 protection, double insulation and a programmable MUSA electronic controller. Temperature can be adjusted from 7–30 °C, with COMFORT, NIGHT, ANTIFREEZE, TIMER-2H and CHRONO modes, open-window detection and button lock. The towel warmer is filled with a mixture of 90% water and 10% glycol and is supplied with a rotatable black heating element and a 1.1 m power cable with plug.