Electric towel warmer | heated towel rail | with timer | programmable | 750W | 230V | IP44 | 600x1600mm | white | ADAX Wave 60-160-750 WHITE

Electric heated towel rail | towel warmer | 750 W | 600 × 1600 mm | 15 bars | IP44 | matt black RAL 9035 | ADAX Wave 60-160-750 Black

ADAX Wave 60-160-750 Black is a matt black electric ladder-type heated towel rail designed for drying and warming towels and providing additional bathroom comfort. The model features 15 rectangular-profile bars, a 750 W electric heating element, programmable MUSA controller, 7–30 °C temperature adjustment and IP44 protection rating. The matt black RAL 9035 finish and understated Scandinavian design are particularly well suited to modern, minimalist and dark-accent bathroom interiors.

ADAX Wave 60-160-750 Black combines towel drying, electric heating and programmable temperature control in one appliance. The larger 600 × 1600 mm dimensions and 15 bars provide more space for towels, while the 750 W rated power provides higher heating output. The integrated MUSA controller supports COMFORT, NIGHT, ANTIFREEZE, TIMER-2H and CHRONO modes, weekly and hourly programming, open-window detection and button-lock functions.

Ready to use: the heated towel rail is already filled with heat-transfer fluid and fitted with a programmable electric heating element, so after mechanical installation it only needs to be properly connected to the electrical supply.

Unlike ladder designs with round-profile tubes, ADAX Wave uses rectangular-profile black-steel tube bars. The model has 15 horizontal bars, providing more space for hanging and drying several everyday towels. The 600 × 1600 mm dimensions are particularly suitable where a larger towel warmer and increased usable hanging area are required.

The installed black electric heating element is rotatable. This allows the heated towel rail to be adapted during installation so that the controller is positioned on the more convenient side – either right-hand or left-hand installation can be selected.

The appliance is switched on or placed into standby using the [On/Standby] button.

• When switched on, the display shows the current time, selected operating mode and set temperature.
• In standby mode, the current time, day of the week and [Stb] message are displayed.
• When switching to standby, the appliance emits two 0.5-second beeps.
• When switching on, one approximately 1-second beep is emitted.

Two main temperature levels can be set:

• COMFORT temperature is used in COMFORT, CHRONO and, where applicable, FIL-PILOT modes.
• NIGHT temperature is used in NIGHT and CHRONO modes.
• The configurable temperature range is 7–30 °C.
• NIGHT temperature must be at least 0.5 °C lower than COMFORT temperature.

COMFORT mode steadily maintains the selected room temperature. Press [Prog] until the COMFORT icon appears, then set the required temperature using [+] and [−].

NIGHT mode maintains a lower temperature than COMFORT. It is recommended at night or when the room will remain unused for 2 hours or more. NIGHT temperature can be adjusted from 7 °C up to COMFORT temperature minus 0.5 °C.

In ANTIFREEZE mode the temperature setting is fixed at 7 °C. The heating element activates when room temperature falls below this level. This mode is practical during holidays, in guest rooms and other rarely used spaces.

TIMER-2H mode is intended for faster drying of damp towels or short-term intensive room heating. In this mode the appliance operates at its maximum 750 W power for up to 2 hours, up to a maximum room temperature of 30 °C. Afterwards it automatically returns to the previously selected operating mode.

CHRONO mode allows an individual 7-day heating schedule to be created. Each hour of every day can be assigned:

• COMFORT temperature – shown as a filled time bar.
• NIGHT temperature – shown as an empty time bar.

This makes it possible to reduce the temperature automatically at night or when the bathroom is not in use and return to COMFORT temperature before the expected usage time.

1. Switch the appliance to STANDBY mode.
2. Hold [−] for at least 3 seconds.
3. [SEt] appears at the top of the display.
4. Use [+] to select [tEd].
5. Press [Prog] and set the day of the week.
6. Confirm the selected day with [Prog].
7. Set the hours using [+] and [−] and confirm with [Prog].
8. Set the minutes in the same way.
9. At the end of the procedure, the controller returns to STANDBY mode.

1. Switch the appliance to STANDBY mode.
2. Hold [−] for at least 3 seconds until [SEt] appears.
3. Use [+] to select [Pro9].
4. Press [Prog] to enter programming mode.
5. For each hour of the day press [+] for COMFORT or [−] for NIGHT temperature.
6. Press [Prog] to confirm the programme for day 1.
7. Repeat the same procedure for the remaining 6 days.

Open-window detection reacts to a sudden drop in room temperature. If such a change is detected, the heating element is temporarily switched off. Heating resumes when an increase in temperature indicates that the window has been closed.

The function can be enabled or disabled in the controller settings. When active, the Open Window icon is shown on the display.

Note: an open window may not be detected if the thermostat is located in an isolated area away from air currents, near an external heat source or if the room temperature changes too slowly.

To prevent accidental changes to temperature or programmes, the control buttons can be locked. Holding [Prog] for approximately 3 seconds locks all buttons except [On/Standby]. A lock symbol appears on the display. To unlock, hold [Prog] again for approximately 3 seconds.

FIL-PILOT mode applies only to products equipped with the Fil-Pilote system. In such versions, the operating mode can be set by a centralised building or home heating-control system. Compatibility must be checked according to the specific product configuration.

• Bathrooms.
• Drying and warming towels.
• Supplementary bathroom heating.
• Sanitary rooms in houses and apartments.
• Hotel and guest-house bathrooms.
• Modern, minimalist and dark-accent interiors.
• Rooms where a larger towel-hanging area is required.
• Rooms requiring programmable electric heating.

1. Always disconnect the power supply before installation or electrical work.
2. Install vertically on a suitable and sufficiently strong wall.
3. Take the larger 600 × 1600 mm dimensions into account and check the installation area in advance.
4. Use mounting screws suitable for the wall construction.
5. The appliance must not be installed with the electrical controller at the top.
6. The lowest heated bar should be at least 600 mm above the floor.
7. Leave at least 50 cm of free space in front of the appliance.
8. Do not place objects closer than approximately 10 cm.
9. The heater must not be installed directly below an electrical socket.
10. Installation and electrical work must be performed by a qualified person in accordance with applicable requirements.

The towel warmer has an IP44 protection rating and is protected against splashing water. It may be installed in bathroom Zone 2 provided that electrical controls cannot be reached by a person using the bath or shower.

Electrical safety: in rooms containing a bath or shower, the supply circuit must be protected by an appropriate residual-current device with a rated residual current not exceeding 30 mA where required by applicable installation rules.

• Switch off the appliance and allow it to cool before cleaning.
• Use cold or lukewarm water not exceeding 25 °C.
• Use a soft, non-abrasive cloth.
• A neutral or mildly alkaline cleaner may be used for stubborn stains.
• Avoid vigorous rubbing or scrubbing.
• Do not use scraping tools, abrasive sponges or rough materials.
• Do not use acidic or strongly alkaline cleaners.
• Do not use steam cleaners.
• Do not use aggressive organic solvents.
• Do not use cleaning products with an unknown chemical composition.
• After cleaning, immediately rinse the surface with clean cold water.

• Maximum stated touchable-surface temperature – 80 °C.
• Some parts may become very hot during operation.
• The appliance is intended for drying towels but must not be completely covered.
• Completely covering it may raise the temperature and activate internal protection.
• Do not sit on the appliance or use it as a chair, support, ladder or toy.
• Particular care is required around small children and vulnerable persons.
• Children must not play with the appliance.
• A damaged power cable or electrical controller must be replaced by a qualified person.
• Disconnect the power supply before maintenance.
• The appliance is not intended for use at altitudes above 2000 m.

Power interruption: CHRONO information – current day, time and daily programme – remains stored in memory for several minutes.

ADAX Wave 60-160-750 Black | electric heated towel rail | towel warmer | 750 W | 600 × 1600 mm | 15 bars | IP44 | matt black RAL 9035

ADAX Wave 60-160-750 Black is a matt black RAL 9035 electric ladder-type heated towel rail with 750 W power and 600 × 1600 mm dimensions. It has 15 rectangular-profile bars, IP44 protection and a programmable MUSA electronic controller. Temperature can be adjusted from 7 to 30 °C, with COMFORT, NIGHT, ANTIFREEZE, TIMER-2H and CHRONO modes, open-window detection and button lock. The towel warmer is filled with a 90% water / 10% glycol mixture and supplied with a rotatable black heating element and 1.1 m power cable with plug.