Products catalog

  • Waterproof luminaire housing for LED tubes | 2× T8 150 cm | single-ended supply | 2x58W | 230V | 1560x115x90 mm | IP65 | without tubes | SW06258

    Code: SW06258
    Barcode: 206000114351

    Waterproof (IP65) surface-mounted luminaire housing for two 150 cm T8 LED tubes with single-ended supply. Supplied pre-wired, without tubes. Designed for garages, warehouses, basements and technical rooms.

  • Waterproof luminaire housing for LED tubes | 2× T8 150 cm | single-ended supply | 2x58W | 230V | 1560x115x90 mm | IP65 | without tubes | SW06258

    Surface-mounted waterproof luminaire housing for two 150 cm T8 LED tubes with single-ended supply. Designed for damp, dusty and unheated rooms – garages, warehouses, farm buildings. Supplied with internal wiring ready; tubes are purchased separately.

    Key point:
    When you need to replace an old 2×58 W fluorescent fitting or install new lighting in a damp room, this housing lets you choose the LED tube power, colour temperature and brand yourself. Later only the tube is replaced, not the whole luminaire.
    Tubes
    2× T8 LED, 150 cm
    Supply
    From one end of the tube
    Protection
    IP65
    Dimensions
    1560 × 115 × 90 mm

    How it works

    The housing is fixed to the ceiling or wall (surface mounting). The supply cable is brought into the housing and connected to the factory-fitted internal wiring – no additional wiring inside the housing is needed.

    Two 150 cm T8 LED tubes with single-ended supply are inserted into the lampholders. The housing has no ballast or starter required by fluorescent tubes, so it is intended for LED tubes only.

    Once the clear diffuser with matt lines is closed and the clips are fastened, the housing meets IP65 – dust-tight and protected against water jets. The lines in the diffuser spread the light of the tubes.

    Why choose SW06258?
    It is a universal base for LED lighting: tubes can be chosen to suit the room and replaced separately, without dismantling the luminaire or changing the installation.

    Technical specifications

    Product type Waterproof surface-mounted luminaire housing (without tubes)
    Product code SW06258
    Barcode 206000114351
    Tube type T8 LED, single-ended supply
    Tube length 150 cm
    Number of tubes 2
    Power designation 2×58 W (150 cm fluorescent tube class)
    Voltage / frequency 230 V AC / 50 Hz
    Protection rating IP65
    Dimensions (L × W × H) 1560 × 115 × 90 mm
    Diffuser PS (polystyrene), clear with matt lines
    Base and clips ABS plastic
    Colour Grey
    Mounting Surface – ceiling or wall
    Package contents Housing with internal wiring and accessories, without tubes

    Main features

    • IP65 sealing – dust and water jets do not reach the lampholders and connections.
    • Pre-wired inside – the installer only connects the supply cable and inserts the tubes.
    • Single-ended tube supply – voltage is fed to one end of the tube, keeping the wiring simple and clear.
    • Free choice of tubes – power, colour temperature and luminous flux are selected to suit the room.
    • Diffuser with matt lines – light is spread more evenly than through a fully clear cover.
    • 150 cm tube format – the same length class as 2×58 W fluorescent fittings, convenient for upgrades.

    Where is it used?

    • Garages and workshops
    • Warehouses and farm buildings
    • Technical rooms and boiler rooms
    • Basements and utility rooms
    • Indoor car parks
    • Canopies, terraces and shelters – under a roof, out of direct sunlight
    • Production areas without aggressive chemicals

    Use by need

    For the electrician.
    Pre-fitted internal wiring shortens on-site work – just connect the cable and insert the tubes.
    For the garage or farm owner.
    An affordable way to replace an old fluorescent fitting with LED lighting of the brightness you want.
    For the facility manager.
    When a tube fails, only the tube is replaced, not the whole luminaire – lower running costs.

    Practical use

    If a garage still has an old 2×58 W fluorescent fitting with a humming ballast and a yellowed cover, it can be replaced with this housing and two 150 cm single-ended T8 LED tubes. The same supply cable is connected, and the light output depends on the tubes you choose.

    Pros

    • IP65 protection rating
    • Pre-fitted internal wiring
    • Free choice of LED tubes
    • Tubes replaced separately from the housing
    • Simple surface mounting
    • Affordable price

    Cons / limitations

    • Tubes are not included – purchased separately
    • Only for single-ended T8 LED tubes – not suitable for fluorescent or double-ended LED tubes
    • The PS diffuser is more impact-sensitive in the cold and may yellow under UV over time – outdoors install only under a roof, out of the sun
    • The supplier does not state cable entry and terminal parameters – check before installation

    Safety and installation notes

    • Installation and connection must be carried out by a qualified electrician with the circuit de-energised.
    • Before inserting tubes, make sure they are designed for single-ended supply – a double-ended LED tube is not suitable for this housing.
    • Do not fit fluorescent tubes – the housing has no ballast or starter.
    • IP65 is ensured only with a properly sealed cable entry and all diffuser clips closed.
    • Bring the cable in only through the intended entry – do not drill additional holes in the housing.

    Quick selection guide

    2× T8 LED
    150 cm tubes
    Single-ended supply
    IP65
    230 V AC
    1560 × 115 × 90 mm
    Suitable when you need:
    • a waterproof luminaire for a damp or dusty room
    • to replace an old 2×58 W fluorescent fitting with LED lighting
    • to choose the tube power and colour temperature yourself
    Check before use:
    • that the LED tubes are T8, 150 cm and single-ended
    • that the tubes connect directly to 230 V (no external ballast)
    • that the mounting location is protected from direct sunlight
    Important reminder: this is a housing without tubes, not a complete luminaire. It does not replace emergency lighting and has no motion sensor.

    FAQ

    Are tubes included?
    No, the housing is supplied without tubes – you need two 150 cm T8 LED tubes.
    Which tubes can be used?
    Only 150 cm T8 LED tubes with single-ended supply.
    Are fluorescent T8 tubes suitable?
    No, the housing has no ballast or starter, so it is intended for LED tubes only.
    What does 2x58W in the name mean?
    It is the tube length class: a 150 cm fluorescent T8 tube was 58 W, while an LED tube of the same length uses considerably less.
    Can it be installed outdoors?
    Yes, under a roof and out of direct sunlight – IP65 protects against dust and water jets, but the PS diffuser is sensitive to UV.
    Is the housing already wired?
    Yes, it is supplied with internal wiring and accessories – you only connect the supply cable.

    Waterproof luminaire housing for LED tubes | 2× T8 150 cm | single-ended supply | 2x58W | 230V | 1560x115x90 mm | IP65 | without tubes | SW06258

    Waterproof IP65 luminaire housing SW06258 for two 150 cm single-ended T8 LED tubes: 1560 × 115 × 90 mm, PS diffuser with matt lines, pre-fitted internal wiring. Suitable for garages, warehouses, basements and technical rooms.

    Published: 2026-11-01 · Data verified against the supplier specification: 2026-11-01

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Price 4.79 € VAT incl.
    ( 3.96 € VAT excl. )
    Price 4.24 € VAT incl.
    ( 3.50 € VAT excl. )
    Rechargeable LED work torch | 520lm | IP54 | 3,7V/2,2Ah | Brennenstuhl WL 500 A | 1175580
    Code: 4007123667888

    Rechargeable LED work light–floodlight designed for convenient illumination of work areas, equipment, vehicles, electrical panels, technical zones or hard-to-reach places. With a 520 lm luminous flux, three lighting modes, integrated rechargeable battery, magnetic base and rotating hook, this work light is a practical choice for both professional and household use.

    The light features IP54 protection against dust and water splashes, IK07 impact resistance, an ergonomic rubber handle and a durable plastic housing. It is a reliable auxiliary lighting solution for workshops, service areas, garages, installation work, repairs, maintenance or outdoor work under protected conditions. 

    Price 22.89 € VAT incl.
    ( 18.92 € VAT excl. )
  • privacy policy

    Information