Insulator for braided cable installation | 22x16 mm | ceramic | dark brown | 6 pcs.

Dark Brown Ceramic Wire Insulator – Ø16 mm, 22 mm, for Open Retro Wiring, 6 pcs

Dark brown ceramic wire insulator is designed for open installation of braided electrical wires on walls and ceilings. The insulator allows the wire to be secured away from the mounting surface while maintaining the characteristic appearance of classic and retro electrical installations.

The insulator is made of ceramic, with a diameter of Ø16 mm and a height of 22 mm. It is recommended to install the insulators approximately every 0.5 m. The package contains 6 insulators and wood screws for mounting them.

The insulator is designed for use with braided wires intended for open retro wiring installations. Such wires are normally left visible and become part of the overall interior design.

• suitable for surface-mounted wiring;
• for routing wires on walls;
• for routing wires on ceilings;
• helps maintain an orderly wire route;
• matches retro-style electrical installation elements.

The insulator is made of ceramic, which is used for insulating and decorative elements in open electrical installations.

• ceramic construction;
• electrically non-conductive material;
• hard and stable construction;
• glossy decorative surface;
• dark brown colour complements classic interiors.

The dark brown colour gives the insulator the appearance of traditional ceramic and allows it to be used as a visible design element of the electrical installation.

• suitable for classic interiors;
• matches vintage-style finishes;
• suitable for country houses and restored buildings;
• can be used in loft-style interiors;
• matches braided retro-style wires.

It is recommended to install the insulators approximately every 0.5 m.

• helps maintain a straight wire route;
• reduces wire sagging between mounting points;
• helps maintain a uniform appearance of the installation;
• allows neat horizontal and vertical wire routes to be created;
• additional mounting points may be required at bends or near equipment.

• Designed for braided wires – for open retro electrical installations.
• Ceramic construction – for a classic installation appearance.
• Suitable for wall and ceiling mounting.
• Ø16 mm diameter.
• 22 mm height.
• Recommended installation every 0.5 m.
• Wood screws included.
• 6 pcs. per package.
• Suitable for visible electrical installations – when wires become part of the interior.

• Residential buildings – for visible retro-style electrical installations.
• Country houses – combined with classic wooden interiors.
• Restored buildings – for a traditional installation appearance.
• Loft interiors – as a visible technical and decorative element.
• Wooden houses – for surface-mounted braided wiring.
• Cafés and restaurants – for stylised interiors.
• Hotels and guest houses – for classic or vintage design.
• Interior design projects – combined with retro switches, socket outlets and braided wires.

For example, a visible retro-style lighting installation is to be installed in a wooden country house. The planned route of the braided electrical wires is marked on the wall.

Ceramic insulators are mounted along the route approximately every 0.5 m. Additional mounting points may be used at bends, near switches, socket outlets or other installation components.

The braided wire is routed according to the planned route, while the dark brown ceramic insulators also become visible interior design elements.

For homeowners: allows a visible retro-style electrical installation to be created, becoming part of the interior.

For country house owners: complements wooden walls.

For interior designers: the insulators can be combined with braided wires, retro switches, socket outlets and other visible installation elements.

For electricians: it is important to properly plan the wire route, the number of mounting points and use wires specifically suitable for open installations.

For installers: the wall or ceiling material should be assessed and suitable insulator and wood screw mounting selected.

1. Plan the wire route. Mark where the braided wires will be routed along the walls or ceiling.
2. Mark the insulator locations. Approximately 0.5 m spacing is recommended on straight sections.
3. Plan additional mounting points. They may be required at bends, near switches, socket outlets or junction boxes.
4. Check the mounting surface. Assess the wall or ceiling material and its suitability for the wood screws being used.
5. Disconnect the power supply. If working on an existing electrical installation, the circuit must be safely disconnected.
6. Secure the insulator. Insert the wood screw through the central hole of the insulator and secure it to the surface.
7. Do not overtighten the wood screw. Secure the ceramic insulator firmly, but do not apply excessive force.
8. Install the remaining insulators according to the planned route.
9. Route the braided wires through the prepared mounting points.
10. Check the entire route. The wires should be neatly positioned and all insulators securely fastened.

• Use only wires suitable for open electrical installations.
• Plan the wire route before installing the insulators.
• The recommended distance between insulators is approximately 0.5 m.
• Additional mounting points may be required at bends and near installation components.
• Do not overtighten the wood screw to avoid damaging the ceramic.
• Check that the mounting surface is suitable for the wood screws being used.
• Check the actual dimensions of the insulator and wire before installation.
• Electrical installation components must be selected as a compatible system.
• Electrical installation and connection work must be carried out by a qualified professional.

Quick selection guide

Choose the dark brown ceramic wire insulators when you want to create a visible braided-wire electrical installation on walls or ceilings while maintaining a classic, vintage or retro interior style.

Ceramic insulators for visible retro braided-wire installations

Dark brown ceramic wire insulators are designed for open installation of braided electrical wires on walls and ceilings. They allow wires to be neatly routed along the surface while maintaining the characteristic appearance of classic and retro electrical installations.

The diameter of one insulator is Ø16 mm and its height is 22 mm. The insulators are recommended to be installed approximately every 0.5 m, while additional mounting points may be used at bends or near other electrical installation components.

The ceramic construction and dark brown colour complement braided wires, retro switches, socket outlets and other visible installation elements. The package contains 6 ceramic insulators and wood screws for mounting them.