Products catalog

  • LED strip profile | type O | 3m | plaster-in | inner corner | for strips up to 12 mm | 4772124005075

    Code: O-tipo tinkuojamas 3m (potinku,gipsu)
    Barcode: 4772124005075

    Plaster-in aluminium profile for LED strips with perforated wings. The wings are filled together with the plasterboard joints – only the line of light remains, with no visible profile edge. Profile for an inner corner – mounted in the inner corner between wall and ceiling or two walls; light comes from the corner.

  • LED strip profile | type O | 3m | plaster-in | inner corner | for strips up to 12 mm | 4772124005075

    Plaster-in aluminium profile for LED strips with perforated wings. The wings are filled together with the plasterboard joints – only the line of light remains, with no visible profile edge. Profile for an inner corner – mounted in the inner corner between wall and ceiling or two walls; light comes from the corner.

    Key point:
    A “trimless” solution: the profile becomes part of the wall or ceiling, and only the glowing line is visible.

    Technical specifications

    Product typeLED strip profile, plaster-in, inner corner
    Model / markingtype O (020W)
    Barcode (EAN)4772124005075
    MaterialAluminium
    Cover (diffuser)Opal (milky) – even light diffusion
    Width48 mm
    Channel width15 mm
    Height27 mm
    Inner width (strip seat)13 mm
    Max. LED strip width12 mm
    Length3 m
    Set contentsProfile, cover, 4 end caps (with cable hole)
    Country of originChina
    CompliancePassive mechanical product without electrical parts – CE marking under the LVD/EMC directives does not apply. The LED strip and power supply must carry their own CE marking.

    Dimensions are taken from the supplier cross-section drawing (mm). Check the actual profile before milling or plastering.

    Main functions

    • Perforated wings bond firmly with the filler
    • Light line without a visible edge
    • Aluminium dissipates heat from the strip

    Where is it used?

    • Plasterboard ceilings and walls
    • Shadow gaps, niches, stairwells
    • Modern residential and commercial interiors

    Installation

    • Fix the profile to the plasterboard or frame before filling
    • Fill over the wings through the perforation, reinforce with mesh tape
    • Mask the channel before filling so no filler gets in
    • After painting, stick the LED strip and fit the cover

    Pros

    • Minimalist trimless look
    • Strong bond with the filler
    • Cover and end caps included

    Cons / limitations

    • Installed at the construction/finishing stage
    • The profile is hard to replace later – the strip can be replaced

    Quick selection guide

    Choose this profile if:
    • you are building plasterboard ceilings or walls
    • you want a light line without a visible edge
    Choose another profile if:
    • finishing is already done – choose a surface-mounted or recessed profile

    FAQ

    When to install?
    At the plasterboard installation and filling stage, before painting.
    Which strip fits?
    Strip up to 12 mm wide (inner width 13 mm).

    Safety and installation notes

    • Power LED strips only with safety extra-low voltage (12/24 V DC) from a CE-marked power supply; the 230 V side must be connected by a qualified electrician.
    • Choose a power supply with at least 20 % power reserve.
    • Aluminium dissipates heat only when the profile is not covered by insulation and is in contact with air or a surface – do not plaster over the cover or block the ends.
    • Wear safety glasses when cutting the profile and remove swarf before sticking the strip.

    Concise technical description (LT / EN)

    LT: Profilis LED juostai | O-tipo | 3m | tinkuojamas | vidiniam kampui | juostai iki 12 mm | 4772124005075. Tinkuojamas (po tinku, gipsu) aliuminio profilis LED juostai su perforuotais sparneliais. Sparneliai užglaistomi kartu su gipso kartono siūlėmis – lieka tik šviesos linija be matomo profilio krašto. Profilis vidiniam kampui – montuojamas vidiniame sienos ir lubų ar dviejų sienų kampe, šviesa sklinda iš kampo.
    EN: LED strip profile | type O | 3m | plaster-in | inner corner | for strips up to 12 mm | 4772124005075. Plaster-in aluminium profile for LED strips with perforated wings. The wings are filled together with the plasterboard joints – only the line of light remains, with no visible profile edge. Profile for an inner corner – mounted in the inner corner between wall and ceiling or two walls; light comes from the corner.

    Keywords

    led strip profile, type o, plaster-in, inner corner, for strips up to 12 mm, led profile, aluminium led channel, led profile with diffuser

    LED strip profile | type O | 3m | plaster-in | inner corner | for strips up to 12 mm | 4772124005075

    A “trimless” solution: the profile becomes part of the wall or ceiling, and only the glowing line is visible. Order at elsprendimai.eu or pick up in Šiauliai, J. Basanavičiaus g. 23.

    Published: 2026-11-18 · Data verified against the supplier technical drawings: 2026-11-18

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

  • privacy policy

    Information