Products catalog

Home/Product Catalog/HVAC control solutions for heating and ventilation/HVAC automation/Speed regulators for fans/Transformer speed controllers for fans
  • New item   -294.67€Temperature-based transformer fan speed and electric heater controller | 3.5A | 230VAC | surface-mounted | Sentera Controls | GTTE1-35L22

    Temperature-based transformer fan speed and electric heater controller | 3.5A | 230VAC | surface-mounted | Sentera Controls | GTTE1-35L22

    Code: GTTE1-35L22
    Inquire about this item
    Price 526.22 € VAT incl.
    ( 434.89 € VAT excl. )
    820.89 € You save 294.67 €
    Offer is valid until 2026-12-31
    Want another price? Suggest yours!
  • Product description

    Temperature-based transformer fan speed and electric heater controller | 3.5A | 230VAC | surface-mounted | Sentera Controls | GTTE1-35L22

    GTTE1-35L22 – Sentera Controls transformer controller of fan speed and electric heater according to temperature. It controls supply and extract fans with single-phase 230 VAC motors (total current up to 3.5 A) and switches an electric heater up to 16 A (3 kW) on / off via a separate Schuko socket.

    Key idea:
    One device for indoor climate: the fans speed up according to temperature, and the heater switches on when heat is lacking. Everything is connected via plugs – the controller is hung on the wall and plugged into a socket.
    What it is for GTTE1-35L22:
    This model is intended for more powerful fans (up to 3.5 A) – roof or duct fans in warehouses, workshops, halls or a group of fans.
    Max. fan current
    3.5 A
    Heater
    Up to 16 A (3 kW), ON/OFF
    Control
    According to temperature 21–35 °C
    Protection
    IP54, plug-in connection

    Operating principle

    The controller is fixed to the wall via the integrated plate and supplied via a 1.5 m cable with a Euro plug (230 VAC / 16 A). The supply and extract fans are connected to two Schuko sockets, the electric heater – to the third (16 A, 3 kW). Each socket is protected by a separate fuse.

    The heart of the controller is an autotransformer with several taps (steps). Each step supplies the motor with a different fixed voltage, while the output voltage remains SINUSOIDAL, as in the mains. As a result, the motor runs quietly even at low speed – the transformer speed controller is also suitable for motors that hum or heat up with an electronic (semiconductor) controller.

    Based on the temperature of the integrated PT500 sensor (4 m), the controller automatically changes the fan speed in five steps between the set limits: the minimum voltage is selected with a knob from 80 / 140 / 170 / 190 VAC, the maximum – from 140 / 170 / 190 / 230 VAC. The temperature is set with a potentiometer at 21–35 °C, proportional band 2 °C, hysteresis 0.2 °C. The electric heater is controlled by on / off switching via an additional output.

    Control is in steps, not stepless: the speed changes in jumps between fixed voltages. Engineer's note: the speed at each step depends on the motor and fan characteristics, so after commissioning it is worth checking that the motor reliably starts at the lowest step used.

    Benefits GTTE1-35L22?
    Ventilation and electric heating according to a single temperature setpoint – without a separate thermostat, relays or complex installation.

    Technical specifications

    Product type Temperature-based transformer fan speed and electric heater controller
    Manufacturer / code Sentera Controls / GTTE1-35L22
    Series GTTE1 (3.5 / 7.5 A)
    Supply voltage 230 VAC, 50–60 Hz
    Max. total fan current 3.5 A
    Heater output Schuko socket, up to 16 A (3 kW), on / off
    Fan speed 5 steps, automatically according to temperature
    Min. voltage (knob) 80 / 140 / 170 / 190 VAC
    Max. voltage (knob) 140 / 170 / 190 / 230 VAC
    Output voltage waveform Sinusoidal (autotransformer)
    Temperature setpoint 21–35 °C, potentiometer
    Proportional band / hysteresis 2 °C / 0.2 °C
    Temperature sensor Integrated PT500, 4 m, 500 Ω at 0 °C, measuring range -30…+70 °C
    Connection 1.5 m cable with Euro plug; 2 Schuko sockets for fans, 1 Schuko socket for heater
    Fuse 5×20 mm, T-5.0 A-H; each socket protected separately
    Housing ABS plastic, UL94-V0, grey RAL 7035
    Protection class IP54 (EN 60529), for indoor use only
    Operating environment -10…+40 °C, 5–80 % rH non-condensing
    Packaging dimensions 340×255×155 mm
    Weight 5.00 kg net / 5.80 kg gross
    Compliance LVD 2014/35/EU (EN 60335-1), EMC 2014/30/EU (EN 61000-6-2, EN 61000-6-3)

    Manufacturer documentation

    ✔ Recommended by Elektrotechnikos sprendimai

    Original manufacturer documentation – technical data, wiring diagrams and installation instructions.

    Main functions

    • Fan speed according to temperature – 5 steps between the min. and max. voltages set with the knobs.
    • Electric heater control – separate Schuko socket up to 16 A (3 kW), on / off.
    • Supply and extract – two sockets for supply and extract fans.
    • Integrated 4 m PT500 sensor – no separate sensor needed.
    • Separate socket fuses – a fault in one circuit does not switch off the others.

    Where is it used?

    • Greenhouses
    • Farm buildings, livestock and poultry housing
    • Residential houses, workshops, technical rooms
    • Rooms that need both ventilation and heating

    On-demand operation

    For the farmer and greenhouse owner.
    Ventilation and heating according to a single set temperature, without a separate thermostat.
    For the electrician.
    Plug-in connection, separate fuses for the sockets, integrated sensor.
    For the ventilation installer.
    Min. and max. speed are set with knobs according to the specific fans.

    Application guide: how it is used in practice

    Typical GTTE1-35L22 applications:

    Site What is connected Result Installer's note
    Greenhouse Supply and extract fans → 2 sockets; heater → 3rd socket Ventilation and heating according to a single setpoint Install the sensor in the plant zone, not near the heater
    Poultry house / livestock room Fans → sockets; electric heater → heater socket A constant temperature is maintained Heater – up to 16 A (3 kW)
    Workshops, warehouse Extract fan → socket The fan speeds up as the temperature rises Total fan current – up to 3.5 A
    Quiet operation Min. voltage knob – 80 or 140 VAC At low demand the fans run slowly and quietly Check that the motor starts at the lowest voltage

    How to select the controller current

    Rated current of the motor(s) Recommended model
    up to 3.5 A GTTE1-35L22 (3.5 A) ← this model
    3.5–7.5 A GTTE1-75L22 (7.5 A)
    Rule: controller max. current ≥ rated current of the motor (or the sum of several motors) from the motor nameplate. For a transformer controller the motor starting current is already taken into account by the manufacturer, so no additional margin is needed. Connect several fans only with AC motors of the same type that are voltage-controllable. The heater current is calculated separately (up to 16 A).
    When to choose another solution: no heater control needed – GTT-1 series (with manual mode); water heater and Modbus – GTH21 series; stepless 0-10 VDC control – electronic EVS-1 series.

    Pros

    • Control of fans and an electric heater in one device
    • Heater socket up to 16 A (3 kW)
    • Integrated 4 m PT500 sensor
    • Plug-in connection, separate socket fuses
    • Sinusoidal output voltage – quiet operation
    • IP54 enclosure, operating environment up to +40 °C

    Cons / limitations

    • Step, not stepless control
    • No manual speed mode – automatic control only
    • Temperature setpoint only 21–35 °C
    • The heater is controlled by on / off only
    • No 0-10 VDC, Modbus or TK terminals
    • Single-phase voltage-controllable AC motors only; not suitable for EC fans

    Safety and installation notes

    • Installation and connection must be carried out by a qualified electrician with the power disconnected.
    • Always connect the protective earth (PE).
    • The total rated current of the connected motors must not exceed 3.5 A.
    • Replace the fuse only with one of the same type and rated current as specified in the datasheet.
    • Electric heater power – no more than 16 A (3 kW).
    • Connect the controller to an earthed socket whose circuit is rated for the combined load of the fans and heater.
    • For indoor use only (-10…+40 °C).

    Quick selection guide

    3.5 A
    230 VAC
    Heater 16 A
    PT500 4 m
    IP54
    Suitable when you need:
    • temperature-based control of fans up to 3.5 A and an electric heater up to 16 A;
    • greenhouses and farm premises;
    • quick plug-in connection.
    Check before use:
    • the total fan current and whether the motors are voltage-controllable;
    • the heater current (up to 16 A) and plug;
    • whether the required temperature falls within 21–35 °C;
    • whether the electrical circuit can handle the total load.
    Important reminder: GTTE1-35L22 does not control EC fans, three-phase motors or water heaters.

    FAQ

    What heater can be connected?
    An electric heater with a Schuko plug up to 16 A (3 kW); it is switched on and off according to temperature.
    How many fans can be connected?
    Two – supply and extract – into separate sockets; their total current up to 3.5 A.
    In what temperature range does it operate?
    Setpoint 21–35 °C, proportional band 2 °C, hysteresis 0.2 °C.
    Can a minimum speed be set?
    Yes, the min. voltage is selected with one knob (80 / 140 / 170 / 190 VAC) and the max. with another knob (140 / 170 / 190 / 230 VAC).
    Is the sensor included?
    Yes, an integrated 4 m PT500 sensor.

    Temperature-based transformer fan speed and electric heater controller | 3.5A | 230VAC | surface-mounted | Sentera Controls | GTTE1-35L22

    Sentera GTTE1-35L22 – temperature-based transformer controller for fan speed and electric heater, fans up to 3.5 A, heater up to 16 A, 230 VAC, PT500 4 m, IP54.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.

  • Subscribtion to new arrivals

    privacy policy

    Information