Products catalog

  • Structure for mounting a lightning rod mast up to Rd48mm on a flat roof | R-600mm | MJ546

    Code: LVGMJ546

    Roof structure designed for reliable installation of lightning rods, antennas, flags, or other technical masts (up to Rd48 mm) on flat roofs without damaging the roofing. It is an efficient and safe solution that allows stable installation of masts using counterweights and guy wires, avoiding drilling into the roof structure.

    Due to its robust construction, hot-dip galvanized steel, and modular system, this solution is widely used in lightning protection systems, as well as in the installation of communication, signaling, and engineering equipment. 

  • Structure for mounting a lightning rod mast up to Rd48 mm on a flat roof | R 600 mm | MJ546 | Liva Group

    MJ546 – a roof structure designed for mounting masts with a diameter up to Rd48 mm on a flat roof. The structure can be used for mounting lightning rods, antennas, flags and other technical masts when drilling or otherwise damaging the roof covering is undesirable.

    The structure is used together with concrete counterweights, allowing the mast to be stabilised on the roof surface without directly fastening the structure through the roof covering. The number of counterweights and the use of additional guy wires are selected according to the specific mast system.

    MJ546 is made of hot-dip galvanised steel. This surface treatment is intended to protect the structure against corrosion and atmospheric effects. Structure radius – R = 600 mm.

    The set includes the structure itself, 6 bolts, nuts and threaded rods. Concrete counterweights, guy wires and their additional components are not included and must be selected separately.

    Key point

    MJ546 – a hot-dip galvanised steel structure for a mast up to Rd48 mm, designed for installation on a flat roof using counterweights. Structure radius – 600 mm. The solution allows installation of the mast without drilling the roof covering and can additionally be equipped with guy wires, rings and counterweight holders.

    Mast diameter
    up to Rd48 mm
    Structure radius
    R = 600 mm
    Material
    hot-dip galvanised steel
    Installation principle
    with counterweights, without roof drilling

    Operating principle

    The MJ546 structure is installed on a flat roof surface and used as a mast support structure. The mast is fixed in the structure, while concrete counterweights are used to stabilise the complete system.

    This installation principle avoids fastening the structure through the roof covering. Depending on the mast height and the specific system, different quantities of counterweights and additional guy wires may be used.

    Installation without drilling: the structure is stabilised with concrete counterweights, so the roof covering does not need to be drilled.

    What are the benefits of this structure?

    Mast stabilisation
    The structure is used to install a mast securely on a roof surface.
    No roof drilling
    The system is used with concrete counterweights, so the roof covering does not need to be drilled.
    Modular configuration
    Different quantities of counterweights and guy wires can be selected according to the mast system.
    Hot-dip galvanising
    Hot-dip galvanised steel is intended to provide protection against corrosion and atmospheric effects.
    Up to Rd48 mm
    The structure is suitable for masts with a diameter not exceeding Rd48 mm.
    Additional accessories
    Can be configured with guy wire systems, rings and counterweight holders.

    Hot-dip galvanised steel structure

    The structure is made of hot-dip galvanised steel. The galvanised surface helps protect the steel against rust, moisture and atmospheric effects.

    Thanks to this feature, MJ546 can be used outdoors for lightning protection, communications, alarm and other technical mast systems.

    For masts up to Rd48 mm

    MJ546 is designed for masts with a diameter of up to Rd48 mm. Before configuring the system, the outer diameter of the mast being used must be checked.

    Important: the structure is designed for masts up to Rd48 mm. For a larger-diameter mast, another suitable mounting structure must be selected.

    Technical specifications

    Product type Roof mast mounting structure
    Model / code MJ546
    Application Mounting masts on a flat roof
    Suitable mast diameter Up to Rd48 mm
    Structure radius R = 600 mm
    Installation type Without roof drilling, using counterweights
    Material Hot-dip galvanised steel
    Resistance Corrosion and atmospheric effects
    Set contents Structure, 6 bolts, nuts, threaded rods
    Counterweights included No
    Guy wires included No, supplied separately
    Manufacturer Liva Group
    Country of origin Turkey

    Use according to need

    For a lightning rod mast
    The structure can be used for a lightning protection system mast up to Rd48 mm.
    For an antenna mast
    Suitable for mounting antennas and other technical masts on a flat roof.
    For a flag mast
    Can be used for a flag mast of a suitable diameter.
    When the roof cannot be drilled
    Stabilisation is achieved using counterweights.
    With guy wires
    The system can additionally be configured with guy wires and their accessories.
    For industrial facilities
    Can be used in factories, warehouses, energy facilities and other technical sites.

    Installation and configuration

    • The structure is placed on a flat roof surface.
    • The mast diameter must not exceed Rd48 mm.
    • Structure radius – R = 600 mm.
    • Concrete counterweights are used for stabilisation.
    • Counterweights are not included.
    • Additional guy wires may be used depending on the mast system.
    • Guy wires, rings and counterweight holders are supplied separately.
    • The set includes the structure, 6 bolts, nuts and threaded rods.

    Compatibility

    The structure is designed for masts with a diameter up to Rd48 mm. It can be used with lightning rod, antenna, flag and other technical masts if their diameter matches the mounting capability of the structure.

    MJ546 can also be configured with guy wire systems, rings and counterweight holders. These additional components are selected separately.

    Applications

    • Lightning protection system masts.
    • Antenna masts.
    • Masts for Wi-Fi equipment or boosters.
    • Flag masts.
    • Communications system equipment.
    • Alarm system equipment.
    • Mounting other technical masts on flat roofs.
    • Residential, commercial and industrial facilities.

    Important before choosing

    • Check that the diameter of the mast being used does not exceed Rd48 mm.
    • The structure radius is 600 mm.
    • Concrete counterweights are not included.
    • Guy wires and their accessories are supplied separately.
    • As the mast height increases, more counterweights and additional guy wires may be required.
    • Sufficient roof space must be provided for the structure and counterweights.

    Advantages and limitations

    Advantages

    • Installation without drilling the roof.
    • Designed for masts up to Rd48 mm.
    • Structure radius R = 600 mm.
    • Hot-dip galvanised steel structure.
    • Resistant to corrosion and atmospheric effects.
    • Used with concrete counterweights.
    • Additional guy wires can be used.
    • Compatible with rings and counterweight holders.
    • Suitable for various technical masts.
    • Mounting hardware included.

    Limitations

    • Concrete counterweights are not included.
    • Guy wires and their components are supplied separately.
    • Suitable only for masts up to Rd48 mm.
    • Space must be provided on the roof for the structure and counterweights.
    • As mast height increases, the required number of counterweights and the total system weight may increase.

    Quick selection guide

    Up to Rd48 mm | R 600 mm | hot-dip galvanised steel | for flat roofs | installation with counterweights | MJ546
    Suitable: when a mast up to Rd48 mm needs to be installed on a flat roof using counterweights without drilling the roof covering.
    Additionally: counterweights, guy wires, rings and counterweight holders are selected separately.
    Check: mast diameter, number of counterweights required for the mast system, need for guy wires and roof area required for the structure.

    FAQ

    1. What is the MJ546 structure designed for?
    It is designed for mounting masts on a flat roof.
    2. Can it be used for a lightning rod mast?
    Yes. A lightning rod mast is one of the main applications of this structure.
    3. What mast diameters is it suitable for?
    For masts up to Rd48 mm in diameter.
    4. What is the structure radius?
    R = 600 mm.
    5. Does the roof need to be drilled during installation?
    No. The structure is designed for installation using counterweights without drilling the roof.
    6. Are concrete counterweights included?
    No. Counterweights are selected separately.
    7. Can guy wires be used?
    Yes. The structure can be configured with a guy wire system.
    8. Are guy wires included?
    No. Guy wires and their accessories are supplied separately.
    9. What material is the structure made of?
    Hot-dip galvanised steel.
    10. Is the structure suitable for outdoor conditions?
    Yes. Hot-dip galvanised steel is intended to protect against corrosion and atmospheric effects.
    11. Can it be used for an antenna mast?
    Yes, if the mast diameter does not exceed Rd48 mm.
    12. Can it be used for a flag mast?
    Yes, if the mast used meets the up to Rd48 mm diameter requirement.
    13. What is included in the set?
    Structure, 6 bolts, nuts and threaded rods.
    14. Who is the manufacturer?
    Liva Group.
    15. What is the country of origin?
    Turkey.

    MJ546 mast mounting structure | up to Rd48 mm | R 600 mm | for flat roofs

    Liva Group MJ546 – a hot-dip galvanised steel structure for mounting lightning rod, antenna, flag and other technical masts up to Rd48 mm on a flat roof. Structure radius – R = 600 mm. The system is installed using concrete counterweights, so the roof covering does not need to be drilled. The structure can additionally be configured with guy wires, rings and counterweight holders.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Anti-corrosion paste | 0.5 kg | for grounding rod connections and contact protection | Galmar
    Code: 11301
    Anti-corrosion paste designed for use in earthing systems, specifically for grounding rod connection points. The paste helps protect metal connections from corrosion, improves contact between earthing system elements, and facilitates the installation of grounding rods when using a driving head. It is a practical supplementary solution for installing a reliable and long-lasting earthing system. 
    Price 10.12 € VAT incl.
    ( 8.36 € VAT excl. )
    Surge protective device Type 1+2+3 (B+C+D) | 1P | Iimp 12.5 kA | In 30 kA | Imax 50 kA | Uc 280 V | Up < 1.3 kV | PO I 1
    Code: SKU#158869360260671971

    PO I 1 is a single-pole Type 1+2+3 (B+C+D) surge protective device: incomer and fine protection stages in one 2.5-module housing. Iimp 12.5 kA (10/350 µs), In 30 kA, Imax 50 kA, Up < 1.3 kV, Uc 280 V.

    Price 34.09 € VAT incl.
    ( 28.18 € VAT excl. )
  • Subscribtion to new arrivals

    privacy policy

    Information