Products catalog

  • Low-profile centrifugal duct fan | D100 | 239 m³/h | 58 W | 230 V | 328 Pa | 341×145×283 mm | galvanised steel | ESLP22879

    Code: ESLP22879

    Low-profile centrifugal duct fan ESLP22879: Ø100 mm, 239 m³/h, 328 Pa, 58 W, 230 V, 341×145×283 mm. Galvanised steel housing, ball bearings, thermal protection, operation from −30 to +60 °C.

  • Low-profile centrifugal duct fan | D100 | 239 m³/h | 58 W | 230 V | 328 Pa | 341×145×283 mm | galvanised steel | ESLP22879

    Centrifugal duct fan for Ø100 mm ducts in a low-profile galvanised steel housing. The 58 W motor delivers up to 239 m³/h and 328 Pa static pressure, and the 145 mm high housing fits in a suspended ceiling void.

    Key point:
    The centrifugal impeller develops high pressure, so the fan overcomes the resistance of longer ducts, grilles and filters. An external-rotor motor with ball bearings and thermal protection – a solution where there is little height for ducts.
    Air flow
    239 m³/h
    Static pressure
    328 Pa
    Power / voltage
    58 W / 230 V
    Height
    145 mm

    How it works

    The fan is installed in the Ø100 mm duct run: air is drawn in through one round spigot and discharged through the opposite one. It is fixed with mounting lugs in any position; the spigots have rubber seals.

    The motor runs at about 2500 rpm with a rated current of 0.25 A. Thermal protection switches the motor off on overheating and restarts it automatically once cool. Terminals are in a sealed terminal box.

    Speed can be controlled with a 230 V thyristor (triac) controller, and operation automated with a timer, humidity or CO₂ sensor.

    Why choose ESLP22879?
    High pressure in a low housing: 239 m³/h and 328 Pa, mounted in a ceiling void where a tall duct fan does not fit.

    Technical specifications

    Product type Low-profile centrifugal duct fan
    Product code ESLP22879
    Supply 220–240 V, 50 Hz
    Power 58 W
    Current 0.25 A
    Speed 2500 rpm
    Air flow 239 m³/h
    Pressure (static) 328 Pa
    Noise 52 dB(A)
    Duct diameter Ø100 mm
    Dimensions 341×145×283 mm
    Motor single-phase, external rotor, ball bearings, thermal protection with automatic restart
    Housing galvanised steel, rubber seals on spigots, sealed terminal box
    Operating temperature −30 to +60 °C
    Mounting any position, mounting lugs
    Country of origin Turkey

    Main functions

    • Low profile – only 145 mm high, fits in a ceiling void.
    • High pressure – up to 328 Pa, overcomes grille and filter resistance.
    • Ball bearings – designed for long operation in any position.
    • Thermal protection – switches the motor off on overheating and restarts it automatically.
    • Sealed connections – rubber seals on the round spigots.
    • Speed control – compatible with a 230 V thyristor controller.
    • −30 to +60 °C – also suitable for unheated lofts.

    How the models in this series differ

    • D100 · 239 m³/h – 328 Pa · 58 W · 52 dB(A) · 341×145×283 mm – this model
    • D125 · 320 m³/h – 326 Pa · 57 W · 54 dB(A) · 341×145×283 mm

    Where is it used?

    • Suspended ceilings and lofts
    • Supply or exhaust systems in flats and houses
    • Offices and shops
    • Bathroom, WC and kitchen extraction via duct
    • Cafés and small commercial premises
    • Basements and plant rooms

    Use by need

    For the designer.
    Known flow, static pressure and 145 mm height – a solution when the Ø100 mm duct zone lacks height.
    For the installer.
    Mounting lugs, sealed spigots and a sealed terminal box – quick installation in a ceiling void.
    For the commercial premises owner.
    Ball bearings and thermal protection – long service with minimal maintenance.

    Practical use

    If the suspended ceiling void is about 200 mm and air must be extracted from a bathroom and kitchen through a Ø100 mm duct with grilles, the 145 mm high ESLP22879 fits in the void and its 328 Pa helps overcome the run resistance. The stated 239 m³/h is without resistance; leave access to the terminal box and mount on anti-vibration pads.

    Pros

    • Up to 239 m³/h and 328 Pa
    • Only 145 mm high
    • Ball bearings, thermal protection
    • Operates from −30 to +60 °C
    • Galvanised steel housing
    • Speed controllable with a thyristor controller

    Cons / limitations

    • Flow drops as system resistance increases
    • Noise 52 dB(A) – use silencers near bedrooms
    • The supplier does not state an IP rating
    • Not for explosive atmospheres and not certified for smoke extraction

    Safety and installation notes

    • Disconnect the supply and verify absence of voltage before installation and maintenance.
    • Provide overload and short-circuit protection; protect bathroom circuits with a 30 mA residual current device (RCD).
    • IP rating not stated – install the fan in the duct outside damp zones, following HD 60364-7-701.
    • Fix to a solid base and leave access to the terminal box.
    • Select the speed controller according to the motor current (0.25 A).
    • Connection must be carried out by a qualified electrician.

    Quick selection guide

    Ø100 mm
    239 m³/h
    328 Pa
    58 W / 230 V
    52 dB(A)
    145 mm
    Suitable when you need:
    • To install a fan in a suspended ceiling
    • Supply or exhaust systems with Ø100 mm ducts
    • To overcome grille and filter resistance
    Check before use:
    • Whether the duct diameter is Ø100 mm
    • Whether the 341×145×283 mm housing fits at the location
    • Whether the terminal box will be accessible
    • Whether the noise level suits the adjacent rooms
    Important reminder: The fan does not recover heat and does not replace a heat recovery unit; it works best when capacity and pressure match the system resistance.

    FAQ

    How is the speed controlled?
    With a 230 V thyristor (triac) speed controller selected for the motor current.
    Can it be mounted in a ceiling void?
    Yes, the 145 mm high housing is designed for that – leave access for servicing.
    Which duct does ESLP22879 fit?
    A Ø100 mm duct.
    Does it have motor protection?
    Yes, thermal protection with automatic restart.
    Is it suitable for an unheated loft?
    Yes, the operating temperature is −30 to +60 °C.
    Is it suitable for smoke extraction?
    No, the fan is not certified for that.

    Low-profile centrifugal duct fan | D100 | 239 m³/h | 58 W | 230 V | 328 Pa | 341×145×283 mm | galvanised steel | ESLP22879

    ESLP22879 is a low-profile centrifugal duct fan for Ø100 mm: 239 m³/h, 328 Pa, 58 W, 230 V, 341×145×283 mm, galvanised steel, ball bearings and thermal protection. For installation in suspended ceilings and lofts.

    Published: 2026-11-13 · Data verified against the supplier specification: 2026-11-13

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Rotary deflector D100 | ball bearings | 300×100 mm | galvanised steel | silver
    Code: 19427

    Galvanised steel rotary deflector (wind turbine) D100 with ball bearings. Fits onto a D100 ventilation duct, extracts air without electricity and protects the duct from rain and snow.

    Price 78.89 € VAT incl.
    ( 65.20 € VAT excl. )
    Digital duct temperature and humidity sensor with LCD | 0–10 V DC / 4–20 mA
    Code: SKU#165278098976225941

    Digital duct sensor that measures air temperature and relative humidity in a duct, shows them on an LCD and sends them to a controller as a 0–10 V DC / 4–20 mA signal.

    Price 168.43 € VAT incl.
    ( 139.20 € VAT excl. )
    Rotary deflector D160 | ball bearings | ABS plastic | blue
    Code: 04512

    ABS plastic rotary deflector D160 with ball bearings, blue. Fits onto a Ø160 mm pipe or ventilation outlet and extracts air without electricity.

    Price 95.59 € VAT incl.
    ( 79.00 € VAT excl. )
  • Subscribtion to new arrivals

    privacy policy

    Information