Products catalog

  • Axial duct fan | D250 | 600 m³/h | 42 W | 230 V | galvanized steel | silver | 18954

    Code: 18954

    Axial duct fan 18954: D250, up to 600 m³/h, 65 Pa, 42 W, 230 V, galvanized steel.

  • Axial duct fan | D250 | 600 m³/h | 42 W | 230 V | galvanized steel | silver | 18954

    Axial fan for D250 ducts: the 42 W, 230 V motor delivers up to 600 m³/h, and the cylindrical housing fits straight into the duct.

    Key point:
    Galvanized steel housing, aluminium impeller and operation from −30 to +60 °C – a simple, economical choice for short duct runs with low resistance.
    Airflow
    600 m³/h
    Power / voltage
    42 W / 230 V
    Pressure
    65 Pa
    Noise
    57 dB(A)

    We will help you set up speed and automatic control

    We will advise how to adjust this fan's speed and how to switch or control it automatically according to room conditions – humidity, temperature or CO₂ concentration. We will select a suitable speed controller, thermostat, humidity or CO₂ sensor and explain how to connect them.

    Contact us: tel. +370 658 01033 or e-mail info@elsprendimai.eu

    In your e-mail, briefly describe the situation: room purpose and size, fan model and what you want to control – speed, humidity, temperature or CO₂.

    Wholesale quantities: special prices for larger orders. State the required quantity in your e-mail and we will send you an individual offer.

    Operating principle

    The axial impeller pushes air along the housing axis, giving high airflow at low power consumption. Such fans work best on short runs without filters and with low resistance.

    Rated current is 0.19 A, maximum pressure 65 Pa. Speed can be adjusted with a 230 V thyristor controller, and operation automated with a timer or humidity sensor.

    Why choose this fan?
    High airflow at low cost: up to 600 m³/h using only 42 W.

    Technical specifications

    Product type Axial duct fan
    Code 18954
    Power supply 230 V AC, 50 Hz
    Power 42 W
    Current 0.19 A
    Airflow 600 m³/h
    Pressure 65 Pa
    Noise 57 dB(A)
    Duct diameter Ø250 mm
    Dimensions Ø250 mm, length 280 mm
    Motor single-phase induction, 230 V
    Impeller aluminium, axial
    Housing galvanized steel, silver
    Operating temperature −30 to +60 °C
    Mounting between ducts, horizontal or vertical
    Country of origin Turkey

    Main functions

    • High airflow – Up to 600 m³/h at low power.
    • Direct installation – Fits between Ø250 mm ducts.
    • Wide temperature range – Operation from −30 to +60 °C.
    • Speed control – Adjustable with a 230 V speed controller.

    Where is it used?

    • Technical and utility rooms
    • Garages, storerooms, workshops
    • Bathroom and kitchen extract
    • Greenhouses and farm buildings
    • Air transfer between rooms

    Use by need

    For designers.
    Simple, clear series data.
    For installers.
    Cylindrical housing fits easily into the duct.
    For businesses.
    Low operating costs.

    Practical application

    The stated 600 m³/h is achieved at zero resistance. Axial fans are sensitive to filters and long runs – if the system has filters, choose a centrifugal or mixed-flow fan.

    Pros

    • Up to 600 m³/h
    • Only 42 W
    • Galvanized steel, aluminium impeller
    • Operation from −30 to +60 °C

    Cons / limitations

    • Low pressure – not for long runs or filters
    • Not for explosive atmospheres
    • Not certified for fire smoke extraction

    Safety and installation notes

    • Connection must be made by a qualified specialist
    • Fit overload protection in the supply circuit
    • Mount the fan on a solid base
    • Disconnect power before maintenance
    • Keep inlet and outlet unobstructed

    Quick selection guide

    600 m³/h
    42 W / 230 V
    65 Pa
    57 dB(A)
    Suitable when you need:
    • ventilate technical or utility rooms
    • build a short extract or supply run with Ø250 mm ducts
    • transfer air between rooms at low cost
    Check before use:
    • whether 230 V supply is available
    • whether the duct diameter is Ø250 mm
    • whether system resistance stays below 65 Pa
    Important reminder: A fan works best when its airflow and pressure match the system resistance.

    FAQ

    Can the speed be adjusted?
    Yes, a 230 V thyristor (triac) speed controller is suitable.
    Is it suitable with filters?
    An axial fan builds little pressure, so for systems with filters we recommend a centrifugal fan.
    Is it suitable for fire smoke extraction?
    No, the fan is not certified for this purpose.

    18954 axial duct fan D250 600 m³/h

    Axial duct fan 18954: D250, up to 600 m³/h, 65 Pa, 42 W, 230 V, galvanized steel.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Shut-off damper for round air duct | for ventilation | air handling systems | D100 | silver | galvanized steel | 100USO
    Code: 04963

    Round duct shut-off damper, designed to shut off, restrict, or regulate airflow in round air ducts. The damper is used in supply, exhaust, or recirculation air systems where simple and efficient control of air movement within premises is required.

    Due to its galvanized steel construction, the product is resistant to corrosion, durable, and suitable for use in residential, commercial, and technical ventilation systems. Manual operation allows easy airflow adjustment without the need for an additional electric actuator or automation system. 

    Price 6.50 € VAT incl.
    ( 5.37 € VAT excl. )
    Flexible aluminum air duct | for ventilation | ventilation systems | D100mm | 3m | white | LAO100B
    Code: 23033

    Flexible aluminium air duct - a reliable and universal solution for professional and residential ventilation systems. Designed to connect ventilation elements, fans, heat recovery components or other air distribution units.

    Due to its low weight, high flexibility and resistance to high temperatures, the duct ensures quick installation, tightness and long-term operation even in more demanding conditions. The white surface blends aesthetically in technical and visible installation areas. 

    Price 7.20 € VAT incl.
    ( 5.95 € VAT excl. )
    Rotary deflector D100 | ball bearings | stainless steel | silver
    Code: 19471

    Stainless steel rotary deflector (wind turbine) D100 with ball bearings. Fits onto a D100 ventilation duct, extracts air without electricity and protects the duct from rain and snow.

    Price 85.06 € VAT incl.
    ( 70.30 € VAT excl. )
    Supply air ventilation damper in wall | with G3 filter | ASA plastic wall outlet | D125 | 1m | white | 12,5TOV1-02
    Code: 09230

    Wall-mounted supply air vent D125 with a 1000 mm insulated duct, G3 filter and adjustable diffuser. Outdoor side – ASA plastic external wall outlet. Intended for controlled air inflow in rooms with forced exhaust.

    Price 30.65 € VAT incl.
    ( 25.33 € VAT excl. )
  • privacy policy

    Information