Electrical installation junction box with hinged cover | with screws | plastic | hermetic | 210x190x100mm | surface-mounted | grey | IP67

Electrical installation distribution box | ABS plastic | sealed | 210x190x100mm | hinged lid | surface-mounted | grey | IP67

Robust sealed electrical installation distribution box made of grey RAL 7035 ABS plastic. Designed to protect electrical installation connections, automation components, electronic and control equipment from dust, water and mechanical impact. The 210 × 190 × 100 mm enclosure features IP67 protection, IK07 mechanical resistance and 3 mm thick walls. The box has a hinged lid attached to the enclosure that opens like a door, so it does not need to be completely removed during installation or maintenance work. The lid is sealed with a silicone gasket and closed with red glass-fibre-reinforced nylon screws. Mounting screws and installation accessories are included.

Key point:
An enclosure for electrical and automation equipment must not only protect the components inside, but also provide convenient access during installation and maintenance. The 210 × 190 × 100 mm ABS box uses a hinged lid that remains attached to the enclosure and opens like a door. This construction provides convenient access to the internal space, while after closing the lid the silicone sealing gasket helps maintain IP67 protection. The 3 mm thick ABS walls provide structural rigidity, while the concealed wall-mounting points ensure a neat installation.

Why is this box useful?
The hinged lid simplifies access to the inside of the enclosure because it does not need to be completely removed and placed beside the installation area. This is convenient in electrical installations, automation and control systems where periodic component inspection or maintenance is expected. IP67 protection, the silicone sealing gasket, IK07 mechanical resistance and the rigid 3 mm ABS enclosure provide a reliable protective solution for various technical environments.

• IP67 protection class – protection against dust and temporary immersion in water under specified test conditions.
• IK07 mechanical resistance – the enclosure corresponds to the 2 J impact energy mechanical resistance class.
• Hinged lid – opens like a door and remains attached to the enclosure by hinges.
• Convenient access to internal equipment – the lid does not need to be completely removed during installation or maintenance.
• 3 mm thick ABS walls – rigid construction designed to protect electrical and electronic components.
• Silicone sealing gasket – seals the joint between the lid and base.
• PA6-GF30 lid screws – nylon fastening elements reinforced with 30% glass fibre.
• Concealed fixing points – neat mounting of the enclosure to the selected surface.
• RAL 7035 grey colour – neutral technical colour suitable for industrial and electrical equipment environments.
• Plastic enclosure – does not corrode and is electrically non-conductive.
• Operating temperature – from −20 °C to +70 °C.
• UL 94 HB flammability class – plastic flammability characteristic according to UL 94.
• Universal application – suitable for individually configured electrical connection and automation assemblies.
• Mounting accessories included – screws, wall plugs and washers.

• Electrical installation wire connection and distribution assemblies
• Enclosures for industrial automation and control equipment
• Connection points for sensors, transducers and signal cables
• Connection assemblies for pumps, fans and other equipment
• Lighting power supply and control circuit connections
• Electronic modules and small control systems
• Electrical installations in production equipment and process lines
• Electrical assemblies in technical rooms, boiler rooms and basements
• Installations in greenhouses, utility buildings and other more humid environments
• Enclosures for IoT, communication and remote monitoring equipment
• OEM equipment production and custom electrical and automation projects

For example, a small automation control and cable connection assembly needs to be installed in production equipment. The box is fixed to the equipment structure using the designated mounting holes with 178 × 208 mm spacing. Project-specific control components and connection elements are installed inside the enclosure, while cables are routed through suitable sealed entries. During electrical connection or maintenance work, the lid opens sideways like a door and remains attached to the enclosure. After completing the work, the silicone sealing gasket is checked, the lid is closed and secured with the red nylon screws.

• ⚡ Before opening the enclosure, installing components or connecting wires, disconnect the electrical power supply and verify that no voltage is present.
• Mounting hole spacing is 178 × 208 mm and the hole diameter is Ø 5 mm.
• Mount the box on a suitable and sufficiently strong surface using the designated fixing points.
• Before installation, provide sufficient free space for the hinged lid to open.
• When opening the lid, do not apply additional mechanical force to the hinges and do not push the lid beyond its designed movement limit.
• For cable entries, use suitable sealed glands according to cable outer diameter and required protection class.
• When drilling openings, do not damage the hinges, sealing contour or fixing elements.
• For outdoor installation, it is recommended to route cables from below and form a drip loop.
• Before closing, check that the white silicone sealing gasket is clean, undamaged and correctly positioned.
• Tighten the red lid screws evenly without exceeding the appropriate tightening torque.
• Install internal electrical components so that reliable fixing and required electrical clearances are ensured.
• Do not use the enclosure outside the operating temperature range of −20 °C to +70 °C.
• Electrical installation work must be carried out by a qualified specialist in accordance with applicable electrical installation requirements.

Quick selection guide

How does the box lid open?
The lid is hinged and attached to the enclosure. After loosening the fixing screws, it opens sideways like a door. The open lid remains attached to the enclosure.

Does the lid need to be completely removed to access the inside?
No. The hinged lid construction allows access to the internal components without completely removing the lid from the enclosure.

What does IP67 protection mean?
IP67 means complete protection against dust and resistance to temporary immersion in water under IEC 60529 test conditions. The sealing of the installed box depends on suitable cable entries and a correctly closed lid.

What does IK07 mechanical resistance mean?
IK07 means resistance to a 2 J mechanical impact according to IEC 62262 classification.

What is the enclosure wall thickness?
The ABS plastic enclosure wall thickness is 3 mm.

Does the box have a sealing gasket?
Yes. The joint between the lid and enclosure is sealed with a white silicone foam rubber gasket.

What material are the lid screws made from?
The red lid screws are made of nylon 6 reinforced with 30% glass fibre (PA6-GF30).

What are the box mounting dimensions?
Nominal enclosure dimensions – 210 × 190 × 100 mm. Mounting hole spacing – 178 × 208 mm, and mounting hole diameter – Ø 5 mm.

Are mounting screws included?
Yes. The set includes wall mounting screws, additional mounting screws, wall plugs and washers.

Can the box be installed outdoors?
The IP67 protection class and specified UV resistance properties allow the enclosure to be considered for outdoor installation projects. For long-term direct sunlight exposure, the specific UV resistance limits of the material must be evaluated and cable entries must be installed correctly.

What temperature range can the box be used in?
The enclosure operating temperature is from −20 °C to +70 °C. Components installed inside must also meet the intended operating conditions.

Is the box suitable for automation and electronic equipment?
Yes. The enclosure can be used for small automation, electrical connection and electronic assemblies provided their mounting dimensions, electrical characteristics and operating conditions are compatible with the enclosure capabilities.

Sealed ABS distribution box with hinged lid 210 × 190 × 100 mm | IP67 | IK07

Robust grey RAL 7035 ABS plastic enclosure with 3 mm thick walls, IP67 protection, IK07 mechanical resistance and a silicone lid sealing gasket. The hinged lid remains attached and provides convenient access to internal equipment without removing it. Concealed mounting points and the included mounting screws, wall plugs and washers simplify installation. A universal solution for electrical installation connections, automation systems and electronic equipment.