Products catalog

  • Extractor fan with backdraft shutter | D100 | 90 m³/h | 230V | 155x155x108mm | IP24 | ABS plastic | gold / champagne | TY4SA

    Code: 02322

    This fan with a back-draught shutter features a quietly operating motor, lower energy consumption, and two-speed settings. It is suitable for installation in both ceilings and walls (when mounted in the ceiling, the back-draught shutter must be removed). With an IP24 protection rating, it is suitable for use in humid environments, ensuring longer lifespan and safety.

    Quiet operation
    Low energy consumption
    Suitable for ceiling and wall installation
    Fixed with screws
    Two-speed settings
    IP24 protection rating 

  • Extractor fan with backdraft shutter | D100 | 90 m³/h | 230V | 155x155x108mm | IP24 | ABS plastic | gold / champagne | TY4SA

    The extractor fan with backdraft shutter TY4SA removes stale air from bathrooms, toilets, kitchens and storage rooms. It is mounted in a wall or ceiling into a Ø100 mm duct or opening and removes moisture and odours; the backdraft shutter prevents air from flowing back.

    v=>[(v.q?v.q+' m³/h airflow':'')+(v.db?(v.q?', ':'')+v.db+' dB(A) noise':'')+(v.pw?' and '+v.pw+' W power':'')+(v.q||v.db?' – a practical choice for a domestic room.':''),v.f.H?'The humidity sensor switches the fan on when humidity rises after a shower and off once the room is dry – no need to think about the switch.':v.f.T?'The timer keeps the fan running for a while after the light is switched off, so moisture and odours are fully removed.':v.f.C?'The pull-cord switch removes the need for a separate wall switch – convenient in renovations.':'It is usually connected to the light switch: the fan runs while the light is on.',v.f.V?'The backdraft shutter keeps cold air, odours and dust from the duct out when the fan is off.':''].filter(Boolean).join(' ')
    90 m³/h airflow, 25 dB(A) noise and 8.4 W power – a practical choice for a domestic room. It is usually connected to the light switch: the fan runs while the light is on. The backdraft shutter keeps cold air, odours and dust from the duct out when the fan is off.
    Duct diameter
    Ø100 mm
    Airflow
    90 m³/h
    Noise level
    25 dB(A)
    Control
    wall switch

    How it works

    An axial impeller driven by a 230 V motor extracts air from the room into a duct or ventilation shaft, while fresh air enters through the door gap or supply air vents. When the fan is switched off, the backdraft shutter closes and stops reverse airflow.

    Why choose TY4SA?
    A quiet, energy-saving solution for a standard Ø100 mm opening.

    Technical specifications

    Product typeExtractor fan with backdraft shutter
    ModelTY4SA
    Product code02322
    Duct (mounting) diameter100 mm
    Dimensions (H × W × D)155 × 155 × 108 mm
    Mounting dimensions135 × 135 mm
    Spigot depth70 mm
    Supply voltage230 V AC
    Power8.4 W
    Airflow90 m³/h
    Pressure48 Pa
    Noise level25 dB(A)
    Ingress protectionIP24 – protected against splashing water
    Backdraft shutterYes
    ControlExternal switch (e.g. light switch)
    Housing materialABS plastic
    ColourGold / champagne
    Warranty5 years

    Key features

    • Airflow 90 m³/h – sufficient for a bathroom, toilet or storage room
    • 25 dB(A) – quiet operation that does not disturb adjacent rooms
    • 8.4 W power – low energy consumption
    • IP24 – protection against splashing water in damp rooms
    • Backdraft shutter – keeps cold air, odours and dust from the duct out when off

    Where is it used?

    • Bathrooms
    • Toilets
    • Kitchens (general ventilation, not instead of a cooker hood)
    • Laundry and drying rooms
    • Storage rooms, basements
    • Changing rooms, small offices

    Pros

    • Quiet operation – 25 dB(A)
    • Low power – 8.4 W
    • IP24 protection for damp rooms
    • Standard Ø100 mm opening
    • 5-year warranty
    • Backdraft shutter in the housing

    Cons / limitations

    • No timer or humidity sensor – for that, choose fans with a timer or humidity sensor
    • 90 m³/h may be insufficient for a large room or a long duct
    • IP24 – do not install where a direct water jet can reach

    Safety and installation notes

    • Install only with the power disconnected; connection must be made by a qualified electrician
    • In bathrooms, follow the zone requirements of HD 60364-7-701
    • Duct diameter is 100 mm; do not reduce the cross-section and avoid long ducts with many bends
    • Ensure a fresh-air inlet into the room (door gap or supply air vent)

    FAQ

    Which duct does it fit?
    A Ø100 mm duct or opening in a wall or ceiling.
    How is the fan controlled?
    With an external switch, usually together with the light.
    Does it have a backdraft shutter?
    Yes, the shutter is built into the housing and closes when the fan stops.
    Is it suitable for a bathroom with a shower?
    Yes, IP24 protects against splashes; install outside the reach of a direct water jet and follow the zone requirements.

    Extractor fan with backdraft shutter | D100 | 90 m³/h | 230V | 155x155x108mm | IP24 | ABS plastic | gold / champagne | TY4SA

    Extractor fan with backdraft shutter Ø100 mm: 90 m³/h, 25 dB(A), IP24 – for bathrooms, toilets and kitchens.

    Published: 2026-11-17 · Data according to supplier specification

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Rotary deflector D120 | ball bearings | 300×100 mm | galvanised steel | silver
    Code: 19430

    Galvanised steel rotary deflector (wind turbine) D120 with ball bearings. Fits onto a D120 ventilation duct, extracts air without electricity and protects the duct from rain and snow.

    Price 88.33 € VAT incl.
    ( 73.00 € VAT excl. )
    Flexible aluminum air duct | for ventilation | ventilation systems | D100mm | 3m | white | LAO100B
    Code: 23033

    Flexible aluminium air duct - a reliable and universal solution for professional and residential ventilation systems. Designed to connect ventilation elements, fans, heat recovery components or other air distribution units.

    Due to its low weight, high flexibility and resistance to high temperatures, the duct ensures quick installation, tightness and long-term operation even in more demanding conditions. The white surface blends aesthetically in technical and visible installation areas. 

    Price 7.20 € VAT incl.
    ( 5.95 € VAT excl. )
    Duct centrifugal fan | D125 | 370 m³/h | 52 W | 230 V | 310 Pa | plastic housing | white | 15622
    Code: 15622

    Duct centrifugal fan 15622: D125, up to 370 m³/h, 310 Pa, 52 W, 230 V, plastic housing.

    Price 93.17 € VAT incl.
    ( 77.00 € VAT excl. )
    Supply air ventilation damper in wall | with G3 filter | ASA plastic wall outlet | D125 | 1m | white | 12,5TOV1-02
    Code: 09230

    Wall-mounted supply air vent D125 with a 1000 mm insulated duct, G3 filter and adjustable diffuser. Outdoor side – ASA plastic external wall outlet. Intended for controlled air inflow in rooms with forced exhaust.

    Price 30.65 € VAT incl.
    ( 25.33 € VAT excl. )
    Shut-off damper for round air duct | for ventilation | air handling systems | D100 | silver | galvanized steel | 100USO
    Code: 04963

    Round duct shut-off damper, designed to shut off, restrict, or regulate airflow in round air ducts. The damper is used in supply, exhaust, or recirculation air systems where simple and efficient control of air movement within premises is required.

    Due to its galvanized steel construction, the product is resistant to corrosion, durable, and suitable for use in residential, commercial, and technical ventilation systems. Manual operation allows easy airflow adjustment without the need for an additional electric actuator or automation system. 

    Price 6.50 € VAT incl.
    ( 5.37 € VAT excl. )
  • privacy policy

    Information