MC4 connector gel sleeve | for 4–10 mm² cable | up to 1500 V DC | IP68 | 160×43×30 mm | 2 pcs | MC4SOLAR
Code: MC4SOLARPrice 13.48 € VAT incl.( 11.14 € VAT excl. )MC4 hermetic connector – a reliable and innovative solution designed for sealing MC4-type connections in solar and photovoltaic systems. Thanks to the integrated special silicone gel filling, this connector provides long-term protection of contacts from moisture, dust, UV radiation, corrosion, and even extreme conditions, including chlorinated or salty water. It is an ideal solution both for new installations and for protecting connections during system upgrades.
-
MC4 connector gel sleeve | for 4–10 mm² cable | up to 1500 V DC | IP68 | 160×43×30 mm | 2 pcs | MC4SOLAR
A silicone-gel-filled sleeve that hermetically covers a mated MC4 connector in the DC circuit of a solar plant. Designed for 4–10 mm² cables and systems up to 1500 V DC; 2 pcs per pack.
Key point:
An MC4 connector stays sealed only as long as its gaskets and nuts are intact. On flat roofs, near water or where a connector lies in a puddle, an extra gel layer reduces the risk of moisture, dirt and salt reaching the contact – and with it the risk of insulation faults and contact overheating.Cable
4–10 mm²Voltage
up to 1500 V DCProtection
IP68Pack
2 pcsHow it works
The sleeve consists of two polypropylene housing halves filled with silicone gel. The mated MC4 connector is placed in the middle, the cables exit through the ends and the housing is pressed together until it clicks.
The gel surrounds the connector and cable entries, displaces air and moisture and forms a hermetic barrier. The black housing with carbon black additive is UV resistant.
The result is an additionally sealed connector less affected by water, dirt, salt, chlorine and chemicals.
Why choose MC4SOLAR?
Installed in seconds without tools or extra sealing. An inexpensive way to protect connectors where their failure would stop a whole string.Technical specifications
Product type Gel protective sleeve for MC4 connector Product code MC4SOLAR Compatibility MC4 type connectors Cable cross-section 4–10 mm² Operating voltage up to 1500 V DC Dimensions 160 × 43 × 30 mm Housing Polypropylene, UL 94-V2 Filling Silicone gel, UL 94-HB Halogens None Degree of protection IP68 UV resistance Yes (carbon black additive) Flammability CEI 20-35 / IEC 60332-1 / HD 405-1 Operating temperature up to +125 °C Installation temperature -40…+50 °C Self-ignition temperature > 400 °C Quantity per pack 2 pcs Main features
- Gel sealing – protects the contact from water, dirt and salt.
- IP68 – suitable where the connector may end up in water.
- UV-resistant housing – for long-term rooftop use.
- Tool-free installation – the housing simply snaps over the connector.
- Up to 1500 V DC – also usable in higher-voltage strings.
- Halogen-free – fewer corrosive gases in case of fire.
Where is it used?
- Flat roofs where connectors lie on the membrane
- Plants on coasts and near water
- Farm buildings with aggressive atmospheres (ammonia, humidity)
- Ground-mounted plants – connectors close to the ground
- Preventive maintenance of existing plants
- Connectors that are hard to reach for repair
Use by need
For PV installers.
Quick extra sealing at risky spots without additional boxes.For plant owners.
Fewer moisture-related connector faults and less downtime.For maintenance staff.
A simple preventive measure when refurbishing older plants.Practical example
If string connectors on a flat roof lie directly on the membrane and the inverter reports an insulation resistance fault after heavy rain, check and if necessary replace the connectors, mate them and fit MC4SOLAR sleeves. Fix the cables so that the connectors do not lie in water.Pros
- IP68 sealing
- Suits 4–10 mm² cables and up to 1500 V DC
- UV resistant, halogen-free
- Tool-free installation
- Resistant to salt, chlorine and chemicals
- 2 pcs per pack
Cons / limitations
- Only for MC4 type connectors
- Single use – re-use after removal is not recommended
- Does not replace a properly crimped and sealed connector
- Must be removed to disconnect the connector
Safety and installation notes
- Fit the sleeve only over an already mated and checked MC4 connector.
- Work with the inverter and DC isolator switched off.
- Install at -40…+50 °C ambient temperature.
- Do not fit the sleeve over a damaged or burnt connector – replace it first.
- Fix the cables so the sleeve does not hang on the connector.
Quick selection guide
MC44–10 mm²≤ 1500 V DCIP68Silicone gel2 pcsSuitable when you need:- extra connector sealing in damp locations
- protection from dirt, salt or chemicals
- preventive maintenance on an older plant
Check before use:- that the connector is MC4 type
- cable cross-section (4–10 mm²)
- that the connector is sound and properly crimped
Important reminder: the sleeve does not fix a badly crimped connector – it only adds protection to a sound one.FAQ
How many per pack?
2 pcs.Which cables does it fit?
4–10 mm² cables with MC4 connectors.Are tools needed?
No – the housing is pressed together by hand.Can it be reused?
Not recommended – after removal gel sealing is no longer guaranteed.Is it suitable for 1500 V DC systems?
Yes, operating voltage is up to 1500 V DC.Can it be left in water?
The sleeve is IP68, but cables should still be fixed so connectors do not lie in water.MC4 connector gel sleeve | for 4–10 mm² cable | up to 1500 V DC | IP68 | 160×43×30 mm | 2 pcs | MC4SOLAR
MC4SOLAR – silicone-gel-filled sleeve for MC4 connectors, 4–10 mm² cables, up to 1500 V DC, IP68, UV resistant, halogen-free, 2 pcs per pack. Extra connector protection in damp or aggressive environments.
Published: 2026-11-17 · Data verified against supplier specification: 2026-11-17
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.This product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products
Solar PV cable | H1Z2Z2-K | 1x4 mm² | black | 1.5 kV DC | EN 50618 | Dca | IEMMEQU HARCode: H1Z2Z2KThe cable is designed for connecting photovoltaic (solar energy) systems and interconnecting solar modules. This cable offers excellent resistance to ultraviolet (UV) rays, ozone, atmospheric effects, and temperature fluctuations. A durable and flexible single-core copper cable with double insulation ensures long service life and safe use even in the most challenging outdoor conditions. Suitable for installation both indoors and outdoors.
Price 0.98 € VAT incl.( 0.81 € VAT excl. )













