Products catalog

  • Industrial 4G LTE router | Cat 6 up to 300 Mbps | Dual SIM | Wi-Fi 5 | Bluetooth | GNSS | 4 × Gigabit | Teltonika RUTX11

    Code: RUTX11
  • Industrial 4G LTE router | Cat 6 up to 300 Mbps | Dual SIM | Wi-Fi 5 | Bluetooth | GNSS | 4 × Gigabit | Teltonika RUTX11

    The Teltonika RUTX11 is an industrial 4G LTE router for automation, telemetry and remote sites. Two SIM cards, a metal housing, a wide operating temperature range and DIN rail mounting – connectivity in an electrical cabinet, pumping station or vehicle.

    Key idea:
    On an industrial site the connection must work without supervision: in cold, heat and near electrical interference. With two SIM cards the Teltonika RUTX11 automatically switches to another operator if one network fails, and allows secure remote access to equipment via VPN.
    Cellular
    4G LTE Cat 6, up to 300 Mbps
    SIM
    Dual SIM, failover
    Operating temperature
    −40 … +75 °C
    Extras
    GNSS, Bluetooth LE

    Operating principle

    The router is mounted on a DIN rail in a cabinet or on a flat surface, LTE antennas are connected (with a weak signal – external antennas raised above the cabinet) and power is supplied.

    The built-in 4G LTE modem connects to the operator network while the second SIM waits in reserve. Controllers, cameras or computers are connected to the Ethernet ports; digital inputs/outputs allow status monitoring and load control.

    The result is a remote site with a stable connection that can be monitored and configured via VPN or the Teltonika RMS system without travelling to site.

    Why choose the Teltonika RUTX11?
    The fast RUTX series model: LTE Cat 6 up to 300 Mbps, 4 Gigabit ports, Wi-Fi 5 Wave 2, Bluetooth LE and GNSS – when a site generates a lot of data (cameras, servers).

    Technical specifications

    Product type Industrial 4G LTE router
    Manufacturer / model Teltonika RUTX11
    Cellular 4G LTE Cat 6 (up to 300 / 50 Mbps), 3G fallback
    LTE module Quectel EP06
    SIM 2 × SIM (2FF), automatic switching
    Ethernet 4 × 10/100/1000 Mbps RJ45 (1 × WAN, 3 × LAN)
    Wi-Fi Wi-Fi 5 (802.11ac Wave 2), dual-band 2.4 + 5 GHz, up to 867 Mbps, MU-MIMO
    Bluetooth Bluetooth Low Energy
    GNSS yes – positioning and time synchronisation
    Inputs / outputs 1 digital input + 1 digital output
    USB USB 2.0
    Antenna connectors 2 × SMA (LTE), 2 × RP-SMA (Wi-Fi), 1 × RP-SMA (Bluetooth), 1 × SMA (GNSS)
    Power supply 9–50 V DC
    Operating temperature −40 … +75 °C
    Installation DIN rail or flat surface
    Management RutOS (web interface), Teltonika RMS remote management
    VPN OpenVPN, IPsec, WireGuard and more

    Key functions

    • 4G LTE Cat 6 – up to 300 Mbps download, 3G fallback
    • Dual SIM – automatic switching to another operator if the connection fails
    • Dual-band Wi-Fi 5 – wireless access for service staff or users
    • Inputs / outputs – door contact, alarm signal, relay control, SMS notifications
    • GNSS – tracking of vehicles or mobile assets, time synchronisation
    • Bluetooth LE – short-range sensor data collection
    • VPN and firewall – secure remote access to site equipment
    • Teltonika RMS – monitoring and configuring many devices from one place

    Where is it used?

    • Water and wastewater pumping stations
    • Solar plants and transformer substations
    • Building automation, boiler rooms, heat substations
    • Video surveillance at remote sites
    • Parking meters, POS, self-service terminals
    • Remote maintenance of industrial equipment
    • Transport: buses, special vehicles, vessels

    Use by need

    Automation / SCADA integrator.
    Ethernet device connection to SCADA via VPN without extra converters.
    Energy engineer.
    Monitoring of a substation, solar plant or pumping station with automatic operator switching.
    Transport company.
    Connectivity and positioning in a vehicle, vibration resistance and a wide temperature range.

    Practical use

    If a pumping station 15 km away must be monitored from the control room and there is no fixed line, the Teltonika RUTX11 is mounted on a DIN rail in the cabinet, the PLC is connected via Ethernet, SIM cards from two operators are inserted, and the dispatcher connects via VPN.

    Pros

    • 4G LTE Cat 6 up to 300 Mbps
    • Dual SIM with automatic switching
    • Operating temperature −40 … +75 °C
    • GNSS positioning
    • Gigabit Ethernet
    • RutOS and Teltonika RMS management
    • Equipment from a Lithuanian manufacturer, extensive documentation

    Cons / limitations

    • No 5G – the fastest connection requires a 5G model

    Safety and installation notes

    • Installation in a cabinet or on a building should be carried out by a qualified electrician following electrical installation rules
    • Connect power only with the voltage switched off; check polarity and voltage range (9–50 V DC)
    • Seal outdoor antenna cables and earth antennas and masts – protection against lightning surges
    • Insert or replace the SIM card only with the power off
    • Do not install close to frequency converters and power cables without separation – interference degrades the connection
    • Change default passwords, update firmware, do not expose the management interface to the internet without VPN

    Quick selection guide

    4G LTE Cat 6
    up to 300 Mbps
    Dual SIM
    Wi-Fi 5
    −40 … +75 °C
    DIN rail
    Suitable when you need:
    • reliable connectivity at an unattended remote site
    • automatic operator switching
    • access to equipment via VPN
    • operation in cold or heat inside a cabinet
    Check before use:
    • operator 4G coverage on site (best measured on location)
    • antenna needs – inside a cabinet or metal enclosure external antennas are required
    • supply voltage and connector type
    • the SIM data plan (M2M / IoT plans are cheaper for telemetry)
    Important reminder: the router does not protect equipment against surges or short circuits – the cabinet needs separate protective devices; it also does not create mobile coverage.

    FAQ

    Does it work with any operator’s SIM?
    Yes – the device is unlocked and works with SIM cards (2FF format) from Baltic and other EU operators.
    Will it work without 4G?
    Yes – with a weak 4G signal it uses the 3G network if the operator still supports it (3G networks are being switched off in the Baltics).
    Can an external antenna be connected?
    Yes – LTE antennas connect via SMA connectors, so external directional antennas can be used.
    How can I access the device remotely?
    Via VPN (OpenVPN, IPsec, WireGuard) or the Teltonika RMS cloud system.
    Where is it installed?
    On a DIN rail, wall or desk – depending on the model (see table).
    What SIM plan do I need?
    A small M2M plan is enough for telemetry; for video cameras and internet use an unlimited data plan.

    Industrial 4G LTE router | Cat 6 up to 300 Mbps | Dual SIM | Wi-Fi 5 | Bluetooth | GNSS | 4 × Gigabit | Teltonika RUTX11

    Teltonika RUTX11 – industrial 4g lte router with 4G LTE Cat 6, Dual SIM. Reliable connectivity for remote sites, automation and telemetry.

    Published: 2026-11-16 · Data verified against the manufacturer datasheet: 2026-11-16

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • privacy policy

    Information