Industrial Dehumidifier | Moisture Collector | 850W | 230V | 60L/24h | 850m³/h | 400x370x700mm | White

Industrial dehumidifier – up to 60 l/day, 850 m³/h, 10 l tank, 850 W, 230 V, for 60–120 m² rooms

Mobile industrial dehumidifier is designed to reduce excess humidity in warehouses, production areas, workshops, basements, laboratories and other larger indoor spaces. The maximum stated dehumidification capacity is 60 litres per dayat an ambient temperature of 30 °C and a relative humidity of 80%.

The unit is microprocessor-controlled and features a digital humidity display, an adjustable target humidity level, automatic defrosting, a 10-litre water tank and a connection for continuous condensate drainage.

The high airflow of up to 850 m³/h helps circulate air in larger rooms, while the castors allow the dehumidifier to be moved conveniently between work areas.

• display of the current relative humidity;
• setting of the desired humidity level;
• automatic operating control;
• retention of settings after a power failure;
• sensor fault indication;
• full water tank warning and automatic shut-off.

• switch off the dehumidifier before removing the filter;
• remove dust using a vacuum cleaner or soft brush;
• if the filter is washed, allow it to dry completely before reinstalling it;
• do not use aggressive solvents;
• do not operate the dehumidifier without the filter installed correctly.

• Dehumidification capacity up to 60 l/day – at 30 °C and 80% RH.
• 850 m³/h airflow – for larger rooms.
• Recommended area of 60–120 m² – with a ceiling height of approximately 3 m.
• Automatic humidity control – according to the set RH level.
• LCD display – for displaying current humidity and operating status.
• Automatic defrosting – for operation in cooler rooms.
• 10 l water tank – with a full-tank warning.
• Continuous drainage – through a Ø14 mm hose.
• Pre-filter – for capturing dust.
• 3-minute compressor protection – after switch-on.
• Metal housing with anti-corrosion coating.
• Castors with locks – for convenient movement.

• In warehouses – to protect goods and packaging against moisture.
• In production areas – to reduce process-related humidity.
• In workshops and garages – to reduce condensation and the risk of corrosion.
• In basements – to control elevated air humidity.
• At construction and renovation sites – to accelerate room drying.
• In archives and paper warehouses – to protect documents and raw materials.
• In printing facilities – to control paper storage conditions.
• In pharmaceutical and laboratory areas – where a specified humidity level must be maintained.
• In tobacco, textile or timber warehouses – to regulate humidity conditions.
• In greenhouses and technical rooms – where the conditions are within the unit's operating limits.

1. Position the dehumidifier upright. Choose a level and stable surface.
2. Lock the castors. The unit must not move by itself during operation.
3. Leave space for air circulation. Do not obstruct the front air inlet or side outlet.
4. Check the filter and water tank. They must be installed correctly.
5. Choose the condensate removal method. Use the water tank or connect a drain hose.
6. Connect the unit to a 230 V mains supply. The electrical socket must be earthed and suitable for the unit's load.
7. Set the desired humidity. Select an RH value suitable for the intended use of the room.
8. Allow the compressor to start. A protective delay of up to 3 minutes may operate after switch-on.
9. Monitor the display. Check the humidity reading, water tank and any fault indications.
10. Carry out regular maintenance. Clean the filter and water tank and inspect the drain hose.

• Use only with a 230 V AC, 50 Hz mains supply.
• The unit must be connected to an earthed socket.
• Do not use outdoors or in locations exposed to rainunless an appropriate IP protection rating is specified.
• Do not use below +5 °C or above +38 °C.
• Do not obstruct the air inlet or outlet.
• Do not move the unit while the compressor is operating.
• Disconnect the power before cleaning or maintenance.
• Do not operate without the air filter.
• Do not allow water to reach electrical components.
• Do not bend or pinch the drain hose.
• Do not dismantle the refrigerant system yourself.
• Repairs must be carried out by a qualified specialist.

• Clean the air filter regularly, especially in dusty rooms.
• Empty and wash the water tankto prevent dirt and odours from developing.
• Check the drain hose – it must not be blocked or kinked.
• Clean the housing with a damp, soft cloth.
• Do not use petrol, acetone or aggressive solvents.
• Listen for changes in the sound of the compressor and fan. Unusual noise may indicate a fault.
• If the dehumidifier will not be used for a long period, store it clean, dry and upright.

Industrial 60 l/day dehumidifier for larger rooms

The mobile condensation dehumidifier is designed to control humidity in warehouses, production areas, workshops, basements and other indoor spaces of 60–120 m².

A dehumidification capacity of up to 60 l/day and an airflow of 850 m³/h allow a large volume of air to be processed, while microprocessor control automatically maintains the set relative humidity.

Condensate can be collected in the 10-litre tank or continuously discharged through a Ø14 mm drain hose. The full-tank warning, automatic shut-off and defrost function simplify everyday operation.

The reinforced metal housing, pre-filter, centrifugal fan and lockable castors are designed for more intensive commercial and industrial use.

The maximum capacity of 60 l/day is achieved only at 30 °C and 80% RH. When selecting a dehumidifier for a specific room, its volume, temperature, initial humidity, air exchange and continuous moisture sources must be considered.