Products catalog

  • Industrial socket board with protection | 2×CEE 16 A 5P + 4×SCHUKO 16 A | with RCD and breakers | 11 modules | IP54 | SEZ ROS 11/FI-23

    Code: ROS11/FI-23 4xVZ 16/S

    SEZ ROS 11/FI-23 is a fully equipped wall-mounted board with two three-phase CEE 16 A 5P and four SCHUKO 16 A sockets.

    • Sockets: 2×CEE 16 A 5P + 4×SCHUKO 16 A
    • Protection: RCD + circuit breakers
    • IP rating: IP54
    • Enclosure: 11 modules, ABS, IK10
  • Industrial socket board with protection | 2×CEE 16 A 5P + 4×SCHUKO 16 A | with RCD and breakers | 11 modules | IP54 | SEZ ROS 11/FI-23

    SEZ ROS 11/FI-23 is a fully equipped wall-mounted board with two three-phase CEE 16 A 5P and four SCHUKO 16 A sockets. The “FI” version is supplied with a residual current device and circuit breakers, so the board is ready for connection.

    Key idea:
    Six sockets and protection in one robust IP54 box – a solution for workshops and service centres where several three-phase and single-phase machines run at the same time. The ROS 11 enclosure is made of thick-walled, impact-resistant ABS.
    Sockets
    2×CEE 16 A 5P + 4×SCHUKO 16 A
    Protection
    RCD + circuit breakers
    IP rating
    IP54
    Enclosure
    11 modules, ABS, IK10

    How it works

    The board is wall-mounted; the supply cable enters through one of the prepared gland openings and is connected to the incoming protection.

    The sockets are protected by a factory-installed residual current device and circuit breakers; the exact ratings are given in the board diagram and device markings.

    The result is a ready distribution point for two three-phase and four single-phase loads.

    Why choose SEZ ROS 11/FI-23?
    No need to select and assemble protection – installation is faster, and six sockets in a workshop eliminate extension leads and multi-plugs.

    Technical specifications

    Product type Wall-mounted board with socket outlets and protective devices
    Manufacturer / model SEZ DK (Slovakia) / ROS 11/FI-23
    Socket outlets 2× CEE 16 A 5P 400 V; 4× SCHUKO VZ 16 A 250 V
    Protective devices Residual current device (RCCB) and circuit breakers – factory-installed
    Protection rating IP54
    Enclosure ROS 11, 11 modules, ABS, IK10, glow-wire resistance 650 °C
    Cable entries Prepared knock-outs for M25, M32, M40, M50 glands
    Operating temperature −25…+40 °C
    Mounting Wall-mounted
    Standard EN 61439-1, EN 61439-3

    Key functions

    • Protection installed – RCD and breakers fitted at the factory.
    • Two CEE 16 A 5P sockets – for two three-phase machines at the same time.
    • Four SCHUKO sockets – for tools, appliances, chargers.
    • IK10 enclosure – impact-resistant for workshop environments.
    • IP54 – protection against dust and splashing water.
    • Cable entries of various sizes – from M25 to M50.

    Where is it used?

    • Car service workshops
    • Metal and wood workshops
    • Production halls
    • Warehouses and logistics centres
    • Farm buildings
    • Technical rooms

    Use by need

    For service owners.
    Six protected sockets in one place – fewer extension leads on the floor and a safer workplace.
    For electricians.
    A factory-assembled and wired board – only the supply connection and measurements remain.
    For building maintenance.
    A standard, robust solution for technological sockets in halls.

    Practical application

    If a compressor, a machine tool and several hand tools run in a workshop, the board is mounted next to the work area, supplied by a three-phase line sized for the actual load, and all six loads are connected to protected sockets without extension leads.

    Advantages

    • Protection installed
    • Six sockets: 2 three-phase + 4 single-phase
    • Robust ABS enclosure IK10
    • IP54
    • Entries M25–M50
    • For −25…+40 °C

    Limitations

    • No CEE 32 A socket – for more powerful equipment choose another ROS 11 model
    • Device ratings fixed by the manufacturer – for specific needs the “/x” version is better
    • A common RCD may disconnect several sockets at once
    • Larger enclosure than compact models

    Safety and installation notes

    • Before connecting, check the board diagram: the sensitivity and type of the installed RCD and which sockets it protects.
    • The supply line protection must correspond to the board rated current on the manufacturer's label.
    • The phase sequence of the three-phase sockets must be the same.
    • Enter the cable through a gland of the correct size – otherwise IP54 is not ensured.
    • Connection and measurements must be carried out by a qualified electrician.

    Quick selection guide

    2×CEE 16 A 5P
    4×SCHUKO 16 A
    RCD + breakers
    IP54
    IK10
    11 modules
    Suitable when you need:
    • A ready multi-socket point in a workshop
    • Two three-phase and several single-phase loads
    • A robust enclosure for impact-prone environments
    Check before use:
    • The ratings of the installed devices in the board diagram
    • Whether your equipment requires a CEE 32 A socket
    • Whether the supply line matches the board rated current
    Important reminder: the board does not protect the supply cable – it is protected by the breaker in the main board.

    FAQ

    Does the board have protection?
    Yes – the “FI” version is supplied with a residual current device and circuit breakers.
    What is the protection rating?
    IP54 according to the manufacturer.
    How many three-phase sockets?
    Two CEE 16 A 5P sockets, 400 V.
    How does ROS 11/x-23 differ?
    The “/x-23” has the same sockets but is supplied without protection.
    Is it suitable outdoors?
    Yes, the manufacturer specifies indoor and outdoor use at −25…+40 °C.
    Can devices be added?
    Only as much as the free space on the 11-module rail allows.

    Industrial socket board with protection | 2×CEE 16 A 5P + 4×SCHUKO 16 A | with RCD and breakers | 11 modules | IP54 | SEZ ROS 11/FI-23

    SEZ ROS 11/FI-23 – a fully equipped IP54 board with two CEE 16 A 5P and four SCHUKO sockets, residual current device and breakers, robust IK10 enclosure. A ready solution for service centres, workshops and production halls.

    Published: 2026-10-30 · Data verified against supplier specification: 2026-10-30

    Published: 2026-11-15 · Data verified against the manufacturer / supplier specification: 2026-11-15

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • privacy policy

    Information