Industrial switch-disconnector | 3P | 315A | FMD4 frame | ~690 V | IP20 | manual operation | Promfactor Baltic | FMD40315
Code: FMD40315Price 116.03 € VAT incl.( 95.89 € VAT excl. )FMD40315 – Promfactor Baltic industrial switch-disconnector 3P 315 A, ~690 V, IP20, in the FMD4 frame with FMC4 accessories, for safe isolation of panels and lines.
-
Industrial switch-disconnector | 3P | 315A | FMD4 frame | ~690 V | IP20 | manual operation | Promfactor Baltic | FMD40315
FMD40315 – a Promfactor Baltic industrial three-pole switch-disconnector in the FMD4 frame with a rated current of 315 A. It is designed for manually switching on, switching off and isolating a three-phase circuit in distribution and incoming panels. The switch-disconnector has no thermal or electromagnetic release – it does not protect against overload and short circuit, so the circuit must be protected by a circuit breaker or fuses installed upstream. Insulation voltage Ui 800 V, rated voltage Un ~690 V, impulse voltage Uimp 8000 V, 50/60 Hz; degree of protection IP20, weight 4.90 kg. Compatible Promfactor FMC4/3U (FMD) accessories: auxiliary contact F/AX4R (right-hand) or F/AX4L (left-hand), 1NO+1NC; alarm contact F/AL4L (left-hand); shunt trip F/SH4230R, 230 V, right-hand; remote control unit MROM34, 230 V.
Key idea:
A switch-disconnector is a clear and reliable isolation point: a single handle isolates all three phases up to 315 A at once, so the panel, line or equipment is disconnected from the supply before repair or maintenance. Since FMD4 uses the same accessories as FMC4 circuit breakers, the switch-disconnector and the circuit breaker in the panel are equipped following the same logic.Rated current
315 ANumber of poles
3PVoltage
Un ~690 V, Ui 800 V, Uimp 8000 VHousing / protection
FMD4, IP20, 4.90 kgOperating principle
The FMD40315 switch-disconnector is mounted in the panel on a mounting plate; supply cables or busbars are connected to the three input terminals and the load to the three output terminals. A protective device must be installed upstream of the switch-disconnector – a circuit breaker (e.g. FMC43U0315 of the same current) or fuses selected according to the cable and load parameters.
When the handle is turned or switched, the contacts simultaneously connect or disconnect all three phases up to a rated current of 315 A. The position status can be transmitted to a controller or control room via the F/AX4R auxiliary contact, and with the MROM34 remote control unit the switch-disconnector can be switched on and off by a remote 230 V signal; with the F/SH4230R shunt trip release it can be switched off by a remote 230 V signal. The switch-disconnector is designed for ~690 V (50/60 Hz) networks, insulation voltage Ui 800 V, impulse withstand voltage Uimp 8000 V; FMD4 frame endurance – 1,500 electrical and 5,000 mechanical on/off cycles.
Result – a clear isolation point for a three-phase circuit up to 315 A, enabling safe repair or maintenance and the use of common FMC4/FMD4 accessories in the control panel.
Benefits FMD40315?
315 A three-pole switch-disconnector in the FMD4 frame with shared FMC4/3U (FMD) accessories – uniform panel equipment for circuit breakers and switch-disconnectors, with the option to signal position and trip the circuit remotely.Technical specifications
Product type Industrial switch-disconnector (load switch-isolator) Manufacturer / code Promfactor Baltic / FMD40315 Series / frame FMD4 (FMD40250 … FMD40400) Number of poles 3P Rated current 315 A Barcode (EAN) 4772151002498 Standard (according to the e-shop product page) IEC/EN 60947-2 Operating frequency 50/60 Hz Insulation voltage (Ui) 800 V Rated voltage (Un) ~690 V Impulse voltage (Uimp) 8000 V Electrical strength 1 500 switching (on/off) cycles Mechanical endurance 5 000 switching (on/off) cycles Degree of protection IP20 Ambient operating temperature -25…+55 °C Storage temperature -25…+70 °C Weight 4.90 kg Control manual, handle on the housing Overload / short-circuit protection none (a protective device upstream of the switch-disconnector is required) Auxiliary contact F/AX4R (right-hand) or F/AX4L (left-hand), 1NO+1NC Signal contact F/AL4L (left-hand) Shunt trip release F/SH4230R, 230 V, right-hand Remote control unit MROM34, 230 V Circuit breaker of the same current rating FMC43U0315 (FMC4/3U, 50 kA) Main functions
- Three-pole isolation – a single handle simultaneously connects or disconnects all three phases up to 315 A.
- Manual control – status and isolation are handled by the installer directly in the control panel, without additional control circuits.
- For networks up to ~690 V – Ui 800 V and Uimp 8000 V – suitable for 400 V and 690 V industrial networks.
- Isolation for repair – the line or control panel section is isolated from the supply before maintenance or equipment replacement.
- Position signalling – auxiliary contact F/AX4R (right-hand) or F/AX4L (left-hand), 1NO+1NC transmits the status to a controller or control room.
- Signal contact – F/AL4L signals that the switch-disconnector has been tripped by the shunt release.
- Remote tripping – the F/SH4230R shunt trip release switches off the switch-disconnector with a 230 V signal – suitable for emergency disconnection.
- Remote control – the MROM34 remote control unit allows the switch-disconnector to be switched on and off by a 230 V signal.
- Shared accessories with FMC4 – the same FMC4/3U (FMD) accessories also fit the FMC43U0315 circuit breaker – smaller stock.
Where is it used?
- Building incoming control panels
- Outgoing 0.4 kV lines of transformer substations
- Production workshop incomers
- Distribution boards in retail and logistics centres
- Pumping stations and water treatment plants
- Backup power (generator) circuits
- Isolation of circuits for scheduled repairs
On-demand operation
For installers on the 0.4 kV side of transformer substations.
The 315 A switch-disconnector suits outgoing lines where a clear three-phase isolation point is required.For control panel manufacturers using FMC43U0315.
an FMD4 switch-disconnector and an FMC4 circuit breaker of the same current are configured with common F/AX4, F/AL4L, F/SH4230R and MROM34 accessories.For electricians in large workshops.
A 315 A production workshop incomer is isolated with a single handle before scheduled work.Practical application
If the panel needs a separate three-phase isolation point for a line whose operating current does not exceed 315 A, then FMD40315 is installed downstream of the protective circuit breaker (e.g. FMC43U0315), all three phases are isolated with a single handle before repairs, and its position is transmitted to the controller via F/AX4R.Application guide: how it is used in practice
FMD40315 adapts to different sites – only what is connected and which accessories are used changes:
Site What is connected Result Installer's note Incoming control panel Incoming cable via a protective circuit breaker → FMD40315 → distribution busbars The whole control panel is isolated with a single handle The switch-disconnector does not protect – select the protective device according to the cable Line or equipment group Circuit supply up to 315 A via FMD40315 The circuit is isolated for repair without affecting other circuits Mark the isolated position and attach a warning sign Remotely monitored site F/AX4R contacts → PLC / BMS input Switch-disconnector position visible remotely Match the contact side (left / right) to the control panel layout Emergency disconnection Emergency button → F/SH4230R (230 V) The switch-disconnector is tripped by a remote signal Take the shunt trip supply from a reliable 230 V source Remote control MROM34 + control signal 230 V The switch-disconnector is switched on and off remotely Order the control unit separately How to select the current and frame of an FMD switch-disconnector
Rated current / frame Recommended model 100 A, FMD3 frame FMD30100 (smaller incomers, building panels) 125 A, FMD3 frame FMD30125 (distribution boards, small incomers) 160 A, FMD3 frame FMD30160 (building and workshop incomers) 200 A, FMD3 frame FMD30200 (power panels, pumping stations) 225 A, FMD3 frame FMD30225 (intermediate size between 200 and 250 A) 250 A, FMD3 frame FMD30250 (highest current of the FMD3 frame) 250 A, FMD4 frame FMD40250 (250 A in the FMD4 frame with FMC4 accessories) 315 A, FMD4 frame FMD40315 (0.4 kV substation lines, workshop incomers) ← this model 400 A, FMD4 frame FMD40400 (highest current of the FMD4 frame) 400 A, FMD5 frame FMD50400 (400 A in the FMD5 frame with FMC5 accessories) 500 A, FMD5 frame FMD50500 (main distribution boards) 630 A, FMD5 frame FMD50630 (highest current of the FMD5 frame) 800 A, FMD6 frame FMD60800 (main incomers, transformer substations) Rule: the rated current of the switch-disconnector must be no lower than the rating of the upstream protective device and the operating current of the circuit. Where the same current is available in two frames (250 A – FMD3 or FMD4; 400 A – FMD4 or FMD5), the smaller frame saves space, while the larger one allows the current to be increased later within the same frame and the use of larger-frame accessories. The switch-disconnector does not provide protection – protection is always provided by a circuit breaker or fuses.When to choose another solution: other currents in the same FMD4 frame – FMD40250, FMD40400; for protection at the same current – circuit breaker FMC43U0315; for modular circuits up to 125 A – FSD3 series modular switch-disconnectors (e.g. FSD34125); accessories – auxiliary contact F/AX4R (right-hand) or F/AX4L (left-hand), 1NO+1NC; signal contact F/AL4L (left-hand); shunt trip release F/SH4230R, 230 V, right-hand; remote control unit MROM34, 230 V.Pros
- Three-pole isolation up to 315 A with a single handle
- Shared FMC4/3U (FMD) accessories with FMC4 circuit breakers
- Position contact F/AX4R (right-hand) or F/AX4L (left-hand), 1NO+1NC
- Remote tripping with the F/SH4230R release
- Clear isolation point for repair and maintenance
- Un ~690 V, Ui 800 V, Uimp 8000 V; 1,500 electrical / 5,000 mechanical cycles
- Remote control with MROM34
Cons / limitations
- Does not protect against overload and short circuit – a circuit breaker or fuses are required upstream of the switch-disconnector
- Auxiliary contacts, releases and control units are ordered separately
- IP20 – install only in a closed panel or cabinet; operating temperature -25…+55 °C
- Three-pole version only – the N conductor is not isolated by the switch-disconnector
Safety and installation notes
- Installation and connection must be carried out by a qualified electrician after disconnecting the supply and verifying the absence of voltage.
- A switch-disconnector is not a protective device – the circuit must be protected by a circuit breaker or fuses selected according to the cable and load.
- Tighten the terminal screws to the torque specified by the manufacturer and use cables or busbars with a cross-section matching the current.
- Before starting work, lock the isolated switch-disconnector or mark it with a warning sign and verify the absence of voltage on the output side.
- Install accessories (contacts, releases, control units) only after the switch-disconnector and its circuits have been de-energised.
Quick selection guide
3P315 A~690 VIP20FMD4Manual controlFMC4 accessoriesRemote controlSuitable when you need:- isolate a three-phase circuit or control panel with an operating current of up to 315 A;
- create a clear isolation point for repair and maintenance;
- configure the control panel with FMC4 circuit breakers and common accessories.
Check before use:- whether the operating current of the circuit and the rating of the protective device upstream of the switch-disconnector do not exceed 315 A;
- whether the circuit is protected by a circuit breaker or fuses;
- which accessories are required: position contact, release, remote control unit.
Important reminder: FMD40315 is a switch-disconnector, not a circuit breaker – it does not protect against overload and short circuit, and accessories are ordered separately.FAQ
Does FMD40315 protect against short circuits?
No, FMD40315 has no protective releases, so a circuit breaker or fuses must be installed upstream of it.What is the rated current of FMD40315?
The rated current of FMD40315 is 315 A, the rated voltage is ~690 V, and the switch-disconnector isolates three poles.Which auxiliary contacts are suitable?
F/AX4R (right-hand) or F/AX4L (left-hand), 1NO+1NC and signal contact F/AL4L (left-hand) are suitable.Can the switch-disconnector be switched off remotely?
Yes, with the F/SH4230R shunt trip release, 230 V, right-hand, and for switching on and off – with the MROM34 remote control unit, 230 V.How does FMD differ from FMC?
FMC4 is a circuit breaker with overcurrent protection, while FMD4 is a switch-disconnector of the same frame series without protection, using shared accessories.How many operations can the switch-disconnector withstand?
The FMD4 frame switch-disconnector withstands 1 500 electrical and 5 000 mechanical switching (on/off) cycles.Industrial switch-disconnector | 3P | 315A | FMD4 frame | ~690 V | IP20 | manual operation | Promfactor Baltic | FMD40315
Promfactor Baltic FMD40315 – industrial three-pole switch-disconnector 315 A in an FMD4 frame with manual operation, compatible with FMC4/3U (FMD) accessories: auxiliary contacts, shunt trip release and remote control unit – for isolating incoming and distribution control panels, lines and equipment groups.
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.ManufacturerThis product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products






