Industrial switch-disconnector | 3P | 400A | FMD5 frame | ~690 V | IP20 | manual operation | Promfactor Baltic | FMD50400
Code: FMD50400Price 215.68 € VAT incl.( 178.25 € VAT excl. )FMD50400 – Promfactor Baltic industrial switch-disconnector 3P 400 A, ~690 V, IP20, in the FMD5 frame with FMC5 accessories, for safe isolation of panels and lines.
-
Industrial switch-disconnector | 3P | 400A | FMD5 frame | ~690 V | IP20 | manual operation | Promfactor Baltic | FMD50400
FMD50400 – a Promfactor Baltic industrial three-pole switch-disconnector in the FMD5 frame with a rated current of 400 A. It is designed for manually switching on, switching off and isolating a three-phase circuit in distribution and incoming panels. The switch-disconnector has no thermal or electromagnetic release – it does not protect against overload and short circuit, so the circuit must be protected by a circuit breaker or fuses installed upstream. Insulation voltage Ui 800 V, rated voltage Un ~690 V, impulse voltage Uimp 8000 V, 50/60 Hz; degree of protection IP20, weight 6.70 kg. Compatible Promfactor FMC5/3U (FMD) accessories: auxiliary contact F/AX5R (right-hand) or F/AX5L (left-hand), 1NO+1NC; shunt trip F/SH5230R, 230 V, right-hand.
Key idea:
A switch-disconnector is a clear and reliable isolation point: a single handle isolates all three phases up to 400 A at once, so the panel, line or equipment is disconnected from the supply before repair or maintenance. Since FMD5 uses the same accessories as FMC5 circuit breakers, the switch-disconnector and the circuit breaker in the panel are equipped following the same logic.Rated current
400 ANumber of poles
3PVoltage
Un ~690 V, Ui 800 V, Uimp 8000 VHousing / protection
FMD5, IP20, 6.70 kgOperating principle
The FMD50400 switch-disconnector is mounted in the panel on a mounting plate; supply cables or busbars are connected to the three input terminals and the load to the three output terminals. A protective device must be installed upstream of the switch-disconnector – a circuit breaker (e.g. FMC53U0400 of the same current) or fuses selected according to the cable and load parameters.
When the handle is turned or switched, the contacts simultaneously connect or disconnect all three phases up to a rated current of 400 A. The position status can be transmitted to a controller or control room via the F/AX5R auxiliary contact, and with the F/SH5230R shunt trip release it can be switched off by a remote 230 V signal. The switch-disconnector is designed for ~690 V (50/60 Hz) networks, insulation voltage Ui 800 V, impulse withstand voltage Uimp 8000 V; FMD5 frame endurance – 1,000 electrical and 4,000 mechanical on/off cycles.
Result – a clear isolation point for a three-phase circuit up to 400 A, enabling safe repair or maintenance and the use of common FMC5/FMD5 accessories in the control panel.
Benefits FMD50400?
400 A three-pole switch-disconnector in the FMD5 frame with shared FMC5/3U (FMD) accessories – uniform panel equipment for circuit breakers and switch-disconnectors, with the option to signal position and trip the circuit remotely.Technical specifications
Product type Industrial switch-disconnector (load switch-isolator) Manufacturer / code Promfactor Baltic / FMD50400 Series / frame FMD5 (FMD50400 … FMD50630) Number of poles 3P Rated current 400 A Barcode (EAN) 4772151002511 Standard (according to the e-shop product page) IEC/EN 60947-2 Operating frequency 50/60 Hz Insulation voltage (Ui) 800 V Rated voltage (Un) ~690 V Impulse voltage (Uimp) 8000 V Electrical strength 1 000 switching (on/off) cycles Mechanical endurance 4 000 switching (on/off) cycles Degree of protection IP20 Ambient operating temperature -25…+55 °C Storage temperature -25…+70 °C Weight 6.70 kg Control manual, handle on the housing Overload / short-circuit protection none (a protective device upstream of the switch-disconnector is required) Auxiliary contact F/AX5R (right-hand) or F/AX5L (left-hand), 1NO+1NC Shunt trip release F/SH5230R, 230 V, right-hand Circuit breaker of the same current rating FMC53U0400 (FMC5/3U, 50 kA) Main functions
- Three-pole isolation – a single handle simultaneously connects or disconnects all three phases up to 400 A.
- Manual control – status and isolation are handled by the installer directly in the control panel, without additional control circuits.
- For networks up to ~690 V – Ui 800 V and Uimp 8000 V – suitable for 400 V and 690 V industrial networks.
- Isolation for repair – the line or control panel section is isolated from the supply before maintenance or equipment replacement.
- Position signalling – auxiliary contact F/AX5R (right-hand) or F/AX5L (left-hand), 1NO+1NC transmits the status to a controller or control room.
- Remote tripping – the F/SH5230R shunt trip release switches off the switch-disconnector with a 230 V signal – suitable for emergency disconnection.
- Shared accessories with FMC5 – the same FMC5/3U (FMD) accessories also fit the FMC53U0400 circuit breaker – smaller stock.
Where is it used?
- Main distribution boards
- 0.4 kV incomers and lines of transformer substations
- Incoming panels of large buildings
- Power control panels in industrial plants
- Logistics and warehouse centres
- Backup power (generator) circuits
- Compensation equipment circuits
On-demand operation
For control panel manufacturers standardising on the FMC5 frame.
The 400 A switch-disconnector in the FMD5 frame uses the same FMC5/3U (FMD) accessories as FMD50500 and FMD50630.For designers with reserve for expansion.
The FMD5 frame allows a switch-disconnector of up to 630 A in the same frame to be installed in the same place later.For energy engineers of logistics and warehouse centres.
A 400 A incomer with an F/SH5230R shunt trip can be switched off remotely by a 230 V signal.Practical application
If the panel needs a separate three-phase isolation point for a line whose operating current does not exceed 400 A, then FMD50400 is installed downstream of the protective circuit breaker (e.g. FMC53U0400), all three phases are isolated with a single handle before repairs, and its position is transmitted to the controller via F/AX5R.Application guide: how it is used in practice
FMD50400 adapts to different sites – only what is connected and which accessories are used changes:
Site What is connected Result Installer's note Incoming control panel Incoming cable via a protective circuit breaker → FMD50400 → distribution busbars The whole control panel is isolated with a single handle The switch-disconnector does not protect – select the protective device according to the cable Line or equipment group Circuit supply up to 400 A via FMD50400 The circuit is isolated for repair without affecting other circuits Mark the isolated position and attach a warning sign Remotely monitored site F/AX5R contacts → PLC / BMS input Switch-disconnector position visible remotely Match the contact side (left / right) to the control panel layout Emergency disconnection Emergency button → F/SH5230R (230 V) The switch-disconnector is tripped by a remote signal Take the shunt trip supply from a reliable 230 V source How to select the current and frame of an FMD switch-disconnector
Rated current / frame Recommended model 100 A, FMD3 frame FMD30100 (smaller incomers, building panels) 125 A, FMD3 frame FMD30125 (distribution boards, small incomers) 160 A, FMD3 frame FMD30160 (building and workshop incomers) 200 A, FMD3 frame FMD30200 (power panels, pumping stations) 225 A, FMD3 frame FMD30225 (intermediate size between 200 and 250 A) 250 A, FMD3 frame FMD30250 (highest current of the FMD3 frame) 250 A, FMD4 frame FMD40250 (250 A in the FMD4 frame with FMC4 accessories) 315 A, FMD4 frame FMD40315 (0.4 kV substation lines, workshop incomers) 400 A, FMD4 frame FMD40400 (highest current of the FMD4 frame) 400 A, FMD5 frame FMD50400 (400 A in the FMD5 frame with FMC5 accessories) ← this model 500 A, FMD5 frame FMD50500 (main distribution boards) 630 A, FMD5 frame FMD50630 (highest current of the FMD5 frame) 800 A, FMD6 frame FMD60800 (main incomers, transformer substations) Rule: the rated current of the switch-disconnector must be no lower than the rating of the upstream protective device and the operating current of the circuit. Where the same current is available in two frames (250 A – FMD3 or FMD4; 400 A – FMD4 or FMD5), the smaller frame saves space, while the larger one allows the current to be increased later within the same frame and the use of larger-frame accessories. The switch-disconnector does not provide protection – protection is always provided by a circuit breaker or fuses.When to choose another solution: other currents in the same FMD5 frame – FMD50500, FMD50630; for protection at the same current – circuit breaker FMC53U0400; for modular circuits up to 125 A – FSD3 series modular switch-disconnectors (e.g. FSD34125); accessories – auxiliary contact F/AX5R (right-hand) or F/AX5L (left-hand), 1NO+1NC; shunt trip release F/SH5230R, 230 V, right-hand.Pros
- Three-pole isolation up to 400 A with a single handle
- Shared FMC5/3U (FMD) accessories with FMC5 circuit breakers
- Position contact F/AX5R (right-hand) or F/AX5L (left-hand), 1NO+1NC
- Remote tripping with the F/SH5230R release
- Clear isolation point for repair and maintenance
- Un ~690 V, Ui 800 V, Uimp 8000 V; 1,000 electrical / 4,000 mechanical cycles
Cons / limitations
- Does not protect against overload and short circuit – a circuit breaker or fuses are required upstream of the switch-disconnector
- Auxiliary contacts, releases and control units are ordered separately
- IP20 – install only in a closed panel or cabinet; operating temperature -25…+55 °C
- The price list has no remote control unit for the FMD5 frame – for remote control choose FMD4 (MROM34) or FMD3 (MROM33)
- The price list has no separate alarm contact for the FMD5 frame – use F/AX5R for status indication
Safety and installation notes
- Installation and connection must be carried out by a qualified electrician after disconnecting the supply and verifying the absence of voltage.
- A switch-disconnector is not a protective device – the circuit must be protected by a circuit breaker or fuses selected according to the cable and load.
- Tighten the terminal screws to the torque specified by the manufacturer and use cables or busbars with a cross-section matching the current.
- Before starting work, lock the isolated switch-disconnector or mark it with a warning sign and verify the absence of voltage on the output side.
- Install accessories (contacts, releases, control units) only after the switch-disconnector and its circuits have been de-energised.
Quick selection guide
3P400 A~690 VIP20FMD5Manual controlFMC5 accessoriesSuitable when you need:- isolate a three-phase circuit or control panel with an operating current of up to 400 A;
- create a clear isolation point for repair and maintenance;
- configure the control panel with FMC5 circuit breakers and common accessories.
Check before use:- whether the operating current of the circuit and the rating of the protective device upstream of the switch-disconnector do not exceed 400 A;
- whether the circuit is protected by a circuit breaker or fuses;
- which accessories are required: position contact, release.
Important reminder: FMD50400 is a switch-disconnector, not a circuit breaker – it does not protect against overload and short circuit, and accessories are ordered separately.FAQ
Does FMD50400 protect against short circuits?
No, FMD50400 has no protective releases, so a circuit breaker or fuses must be installed upstream of it.What is the rated current of FMD50400?
The rated current of FMD50400 is 400 A, the rated voltage is ~690 V, and the switch-disconnector isolates three poles.Which auxiliary contacts are suitable?
F/AX5R (right-hand) or F/AX5L (left-hand), 1NO+1NC are suitable.Can the switch-disconnector be switched off remotely?
Yes, with the F/SH5230R shunt trip release, 230 V, right-hand.How does FMD differ from FMC?
FMC5 is a circuit breaker with overcurrent protection, while FMD5 is a switch-disconnector of the same frame series without protection, using shared accessories.How many operations can the switch-disconnector withstand?
The FMD5 frame switch-disconnector withstands 1 000 electrical and 4 000 mechanical switching (on/off) cycles.Industrial switch-disconnector | 3P | 400A | FMD5 frame | ~690 V | IP20 | manual operation | Promfactor Baltic | FMD50400
Promfactor Baltic FMD50400 – industrial three-pole switch-disconnector 400 A in an FMD5 frame with manual operation, compatible with FMC5/3U (FMD) accessories: auxiliary contacts, shunt trip release – for isolating incoming and distribution control panels, lines and equipment groups.
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.ManufacturerThis product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products






