Products catalog

  • Industrial switch-disconnector | 3P | 800A | FMD6 frame | ~690 V | IP20 | manual operation | Promfactor Baltic | FMD60800

    Code: FMD60800
    Barcode: 4772151002542

    FMD60800 – Promfactor Baltic industrial switch-disconnector 3P 800 A, ~690 V, IP20, in the FMD6 frame with FMC6 accessories, for safe isolation of panels and lines.

  • Industrial switch-disconnector | 3P | 800A | FMD6 frame | ~690 V | IP20 | manual operation | Promfactor Baltic | FMD60800

    FMD60800 – a Promfactor Baltic industrial three-pole switch-disconnector in the FMD6 frame with a rated current of 800 A. It is designed for manually switching on, switching off and isolating a three-phase circuit in distribution and incoming panels. The switch-disconnector has no thermal or electromagnetic release – it does not protect against overload and short circuit, so the circuit must be protected by a circuit breaker or fuses installed upstream. Insulation voltage Ui 800 V, rated voltage Un ~690 V, impulse voltage Uimp 8000 V, 50/60 Hz; degree of protection IP20, weight 8.20 kg. Compatible Promfactor FMC6/3U (FMD) accessories: auxiliary contact F/AX6L (left-hand), 2NO+2NC; shunt trip F/SH6230R, 230 V, right-hand.

    Key idea:
    A switch-disconnector is a clear and reliable isolation point: a single handle simultaneously disconnects all three phases up to 800 A, so the control panel, line or equipment is isolated from the supply before repair or maintenance. Since FMD6 uses the same accessories as FMC6 circuit breakers, the switch-disconnector and circuit breaker are configured in the control panel using the same logic.
    Rated current
    800 A
    Number of poles
    3P
    Voltage
    Un ~690 V, Ui 800 V, Uimp 8000 V
    Housing / protection
    FMD6, IP20, 8.20 kg

    Operating principle

    The FMD60800 switch-disconnector is mounted in the panel on a mounting plate; supply cables or busbars are connected to the three input terminals and the load to the three output terminals. A protective device must be installed upstream of the switch-disconnector – a circuit breaker (e.g. FMC63U0800 of the same current) or fuses selected according to the cable and load parameters.

    When the handle is turned or switched, the contacts simultaneously connect or disconnect all three phases up to a rated current of 800 A. The position status can be transmitted to a controller or control room via the F/AX6L auxiliary contact, and with the F/SH6230R shunt trip release it can be switched off by a remote 230 V signal. The switch-disconnector is designed for ~690 V (50/60 Hz) networks, insulation voltage Ui 800 V, impulse withstand voltage Uimp 8000 V; FMD6 frame endurance – 1,000 electrical and 4,000 mechanical on/off cycles.

    Result – a clear isolation point for a three-phase circuit up to 800 A, enabling safe repair or maintenance and the use of common FMC6/FMD6 accessories in the control panel.

    Benefits FMD60800?
    800 A three-pole switch-disconnector in the FMD6 frame with shared FMC6/3U (FMD) accessories – uniform panel equipment for circuit breakers and switch-disconnectors, with the option to signal position and trip the circuit remotely.

    Technical specifications

    Product type Industrial switch-disconnector (load switch-isolator)
    Manufacturer / code Promfactor Baltic / FMD60800
    Series / frame FMD6 (FMD60800)
    Number of poles 3P
    Rated current 800 A
    Barcode (EAN) 4772151002542
    Standard (according to the e-shop product page) IEC/EN 60947-2
    Operating frequency 50/60 Hz
    Insulation voltage (Ui) 800 V
    Rated voltage (Un) ~690 V
    Impulse voltage (Uimp) 8000 V
    Electrical strength 1 000 switching (on/off) cycles
    Mechanical endurance 4 000 switching (on/off) cycles
    Degree of protection IP20
    Ambient operating temperature -25…+55 °C
    Storage temperature -25…+70 °C
    Weight 8.20 kg
    Control manual, handle on the housing
    Overload / short-circuit protection none (a protective device upstream of the switch-disconnector is required)
    Auxiliary contact F/AX6L (left-hand), 2NO+2NC
    Shunt trip release F/SH6230R, 230 V, right-hand
    Circuit breaker of the same current rating FMC63U0800 (FMC6/3U, 60 kA)

    Main functions

    • Three-pole isolation – a single handle simultaneously connects or disconnects all three phases up to 800 A.
    • Manual control – status and isolation are handled by the installer directly in the control panel, without additional control circuits.
    • For networks up to ~690 V – Ui 800 V and Uimp 8000 V – suitable for 400 V and 690 V industrial networks.
    • Isolation for repair – the line or control panel section is isolated from the supply before maintenance or equipment replacement.
    • Position signalling – auxiliary contact F/AX6L (left-hand), 2NO+2NC transmits the status to a controller or control room.
    • Remote tripping – the F/SH6230R shunt trip release switches off the switch-disconnector with a 230 V signal – suitable for emergency disconnection.
    • Shared accessories with FMC6 – the same FMC6/3U (FMD) accessories also fit the FMC63U0800 circuit breaker – smaller stock.

    Where is it used?

    • Main 0.4 kV incomers of transformer substations
    • Main distribution boards
    • Industrial plant incomers
    • Data centre and hospital electrical systems
    • Incomers of large retail and logistics centres
    • Backup power (generator) circuits
    • Separation of control panel sections

    On-demand operation

    For installers of transformer substations and main incomers.
    The 800 A switch-disconnector – the highest current in the FMD series, intended for the main 0.4 kV incomer.
    For chief energy engineers of industrial plants.
    The position of an 800 A incomer is transmitted to the control room via an F/AX6L contact with 2NO+2NC.
    For designers of data centre and hospital electrical systems.
    An 800 A circuit with an F/SH6230R shunt trip can be isolated remotely by a 230 V signal.

    Practical application

    If the panel needs a separate three-phase isolation point for a line whose operating current does not exceed 800 A, then FMD60800 is installed downstream of the protective circuit breaker (e.g. FMC63U0800), all three phases are isolated with a single handle before repairs, and its position is transmitted to the controller via F/AX6L.

    Application guide: how it is used in practice

    FMD60800 adapts to different sites – only what is connected and which accessories are used changes:

    Site What is connected Result Installer's note
    Incoming control panel Incoming cable via a protective circuit breaker → FMD60800 → distribution busbars The whole control panel is isolated with a single handle The switch-disconnector does not protect – select the protective device according to the cable
    Line or equipment group Circuit supply up to 800 A via FMD60800 The circuit is isolated for repair without affecting other circuits Mark the isolated position and attach a warning sign
    Remotely monitored site F/AX6L contacts → PLC / BMS input Switch-disconnector position visible remotely Match the contact side (left / right) to the control panel layout
    Emergency disconnection Emergency button → F/SH6230R (230 V) The switch-disconnector is tripped by a remote signal Take the shunt trip supply from a reliable 230 V source

    How to select the current and frame of an FMD switch-disconnector

    Rated current / frame Recommended model
    100 A, FMD3 frame FMD30100 (smaller incomers, building panels)
    125 A, FMD3 frame FMD30125 (distribution boards, small incomers)
    160 A, FMD3 frame FMD30160 (building and workshop incomers)
    200 A, FMD3 frame FMD30200 (power panels, pumping stations)
    225 A, FMD3 frame FMD30225 (intermediate size between 200 and 250 A)
    250 A, FMD3 frame FMD30250 (highest current of the FMD3 frame)
    250 A, FMD4 frame FMD40250 (250 A in the FMD4 frame with FMC4 accessories)
    315 A, FMD4 frame FMD40315 (0.4 kV substation lines, workshop incomers)
    400 A, FMD4 frame FMD40400 (highest current of the FMD4 frame)
    400 A, FMD5 frame FMD50400 (400 A in the FMD5 frame with FMC5 accessories)
    500 A, FMD5 frame FMD50500 (main distribution boards)
    630 A, FMD5 frame FMD50630 (highest current of the FMD5 frame)
    800 A, FMD6 frame FMD60800 (main incomers, transformer substations) ← this model
    Rule: the rated current of the switch-disconnector must be no lower than the rating of the upstream protective device and the operating current of the circuit. Where the same current is available in two frames (250 A – FMD3 or FMD4; 400 A – FMD4 or FMD5), the smaller frame saves space, while the larger one allows the current to be increased later within the same frame and the use of larger-frame accessories. The switch-disconnector does not provide protection – protection is always provided by a circuit breaker or fuses.
    When to choose another solution: The FMD6 frame is available only in 800 A; for lower current – FMD50630 (630 A, FMD5); for protection at the same current – circuit breaker FMC63U0800; for modular circuits up to 125 A – FSD3 series modular switch-disconnectors (e.g. FSD34125); accessories – auxiliary contact F/AX6L (left-hand), 2NO+2NC; shunt trip F/SH6230R, 230 V, right-hand.

    Pros

    • Three-pole isolation up to 800 A with a single handle
    • Shared FMC6/3U (FMD) accessories with FMC6 circuit breakers
    • Position contact F/AX6L (left-hand), 2NO+2NC
    • Remote tripping with the F/SH6230R release
    • Clear isolation point for repair and maintenance
    • Un ~690 V, Ui 800 V, Uimp 8000 V; 1,000 electrical / 4,000 mechanical cycles
    • Highest current in the FMD series – 800 A

    Cons / limitations

    • Does not protect against overload and short circuit – a circuit breaker or fuses are required upstream of the switch-disconnector
    • Auxiliary contacts, releases and control units are ordered separately
    • IP20 – install only in a closed panel or cabinet; operating temperature -25…+55 °C
    • The price list has no remote control unit for the FMD6 frame – for remote control choose FMD4 (MROM34) or FMD3 (MROM33)
    • The price list has no separate alarm contact for the FMD6 frame – use F/AX6L for status indication

    Safety and installation notes

    • Installation and connection must be carried out by a qualified electrician after disconnecting the supply and verifying the absence of voltage.
    • A switch-disconnector is not a protective device – the circuit must be protected by a circuit breaker or fuses selected according to the cable and load.
    • Tighten the terminal screws to the torque specified by the manufacturer and use cables or busbars with a cross-section matching the current.
    • Before starting work, lock the isolated switch-disconnector or mark it with a warning sign and verify the absence of voltage on the output side.
    • Install accessories (contacts, releases, control units) only after the switch-disconnector and its circuits have been de-energised.

    Quick selection guide

    3P
    800 A
    ~690 V
    IP20
    FMD6
    Manual control
    FMC6 accessories
    Suitable when you need:
    • isolate a three-phase circuit or control panel with an operating current of up to 800 A;
    • create a clear isolation point for repair and maintenance;
    • configure the control panel with FMC6 circuit breakers and common accessories.
    Check before use:
    • whether the operating current of the circuit and the rating of the protective device upstream of the switch-disconnector do not exceed 800 A;
    • whether the circuit is protected by a circuit breaker or fuses;
    • which accessories are required: position contact, release.
    Important reminder: FMD60800 is a switch-disconnector, not a circuit breaker – it does not protect against overload and short circuit, and accessories are ordered separately.

    FAQ

    Does FMD60800 protect against short circuits?
    No, FMD60800 has no protective releases, so a circuit breaker or fuses must be installed upstream of it.
    What is the rated current of FMD60800?
    The rated current of FMD60800 is 800 A, the rated voltage is ~690 V, and the switch-disconnector isolates three poles.
    Which auxiliary contacts are suitable?
    F/AX6L (left-hand), 2NO+2NC is suitable.
    Can the switch-disconnector be switched off remotely?
    Yes, with the F/SH6230R shunt trip release, 230 V, right-hand.
    How does FMD differ from FMC?
    FMC6 is a circuit breaker with overcurrent protection, while FMD6 is a switch-disconnector of the same frame series without protection, using shared accessories.
    How many operations can the switch-disconnector withstand?
    The FMD6 frame switch-disconnector withstands 1 000 electrical and 4 000 mechanical switching (on/off) cycles.

    Industrial switch-disconnector | 3P | 800A | FMD6 frame | ~690 V | IP20 | manual operation | Promfactor Baltic | FMD60800

    Promfactor Baltic FMD60800 – industrial three-pole switch-disconnector 800 A in an FMD6 frame with manual operation, compatible with FMC6/3U (FMD) accessories: auxiliary contacts, shunt trip release – for isolating incoming and distribution control panels, lines and equipment groups.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

  • Subscribtion to new arrivals

    privacy policy

    Information