Products catalog

  • Insulated bootlace ferrule | 1mm² | 8mm | crimp | red | 100 pcs | Sofamel APF-1,00/8 | 245120

    Code: 245120
    Barcode: 8435157312850

    Insulated wire end ferrule 1 mm² for flexible wires, 8 mm tube, red. Sofamel APF-1,00/8, tin-plated copper, PA collar. 100 pcs per pack.

  • Insulated bootlace ferrule | 1mm² | 8mm | crimp | red | 100 pcs | Sofamel APF-1,00/8 | 245120

    The insulated ferrule terminates a flexible 1 mm² wire before it is connected to a screw or spring terminal. The strands are crimped in a tin-plated copper tube, and the insulating collar protects the wire entry.

    Key point:
    Unsecured strands of a flexible wire splay in the terminal, some break, and the contact weakens and heats up. The ferrule turns the strands into a solid pin – the connection stays reliable after vibration and temperature cycles.
    Cross-section
    1 mm²
    Tube length
    8 mm
    Colour
    red
    Pack
    100 pcs

    Operating principle

    Strip the insulation to the ferrule tube length (8 mm), twist the strands and insert the wire fully – the wire insulation must enter the insulating collar.

    The ferrule is crimped with ferrule crimping pliers using a square or trapezoidal profile. The tube and strands are compressed into one solid pin.

    The crimped pin is inserted into the terminal and tightened to the equipment manufacturer's torque – the terminal clamps solid metal, not individual strands.

    Why choose Sofamel APF-1,00/8?
    Tin-plated copper tube and PA collar; the red colour (Sofamel F) identifies the cross-section at a glance, without measuring.

    Technical specifications

    Product typeInsulated bootlace ferrule (wire end ferrule)
    ManufacturerSofamel (Spain)
    ModelAPF-1,00/8
    Manufacturer code245120
    EAN8435157312850
    Wire cross-section1 mm²
    Tube (pin) length8 mm
    Overall length14.6 mm
    Tube inner Ø1.4 mm
    Collar Ø3 mm
    Collar colourred (colour code Sofamel F)
    Materialelectrolytic copper, tin-plated; insulating collar – polyamide (PA)
    Pack100 pcs
    CertificateUL

    Key functions

    • Strand compression – the terminal clamps the full cross-section, not individual strands.
    • Tin-plated copper – lower contact resistance and protection against oxidation.
    • Insulating collar – protects the wire entry and eases insertion.
    • Colour code – the cross-section is recognised at once during installation and panel inspection.
    • Exact tube length – 8 mm matches the terminal depth – no bare wire, no protruding pin.

    Where is it used?

    • Residential distribution boards
    • Automation and control panels
    • Screw and spring terminal blocks
    • Circuit breakers, RCDs, contactors
    • Controllers, relays, power supplies
    • Motor and equipment connection boxes

    Use by need

    Panel builder.
    Uniform, neat wire ends and faster panel inspection.
    Electrician.
    Flexible wires stay secure in terminals – no re-tightening needed.
    Maintenance technician.
    Fewer loose connections in vibrating equipment.

    Practical use

    If you connect a flexible 1 mm² wire to a circuit breaker in a panel, crimp a ferrule on it – the terminal clamps all strands and the joint does not need re-tightening at periodic inspection.

    Advantages

    • Strands do not splay or break in the terminal
    • Stable contact even under vibration
    • Tin-plated copper – protection against oxidation
    • Colour coding by cross-section
    • Pack of 100 pcs

    Disadvantages / limitations

    • For flexible wires only – not needed for solid wire
    • Requires ferrule crimping pliers – ordinary pliers do not crimp properly
    • Single use – after removal the wire end must be cut off
    • Tube length 8 mm – for a terminal of different depth choose another length

    Safety and installation notes

    • Switch off the voltage and verify it is absent before work.
    • Choose the ferrule exactly to the wire cross-section (1 mm²) – not larger, not smaller.
    • Crimp only with the intended tool and the correct die.
    • Do not use a badly crimped ferrule – cut it off and crimp a new one.
    • Tighten the terminal to the manufacturer's torque and check the wire with a pull test.

    Quick selection guide

    1 mm²
    8 mm
    red
    100 pcs
    Sofamel APF-1,00/8
    Suitable when you need:
    • to connect a flexible wire to a screw or spring terminal
    • a neat, easily inspected connection
    • reliable contact in vibrating equipment
    Check before use:
    • the wire cross-section (1 mm²)
    • the terminal depth and tube length (8 mm)
    • that you have ferrule crimping pliers
    Important reminder: A ferrule does not replace correct sizing of the wire and the protective device – it ensures a quality wire-end connection.

    FAQ

    Is a ferrule needed for solid wire?
    No – it is intended for flexible (stranded) wires.
    Which wire does this ferrule fit?
    A flexible 1 mm² wire.
    What do I crimp it with?
    Ferrule crimping pliers with a square or trapezoidal profile.
    How much insulation should be stripped?
    As long as the tube – 8 mm.
    What does the colour mean?
    The colour indicates the cross-section according to the Sofamel F colour code.
    Can the ferrule be reused?
    No – after removal the wire end must be cut off and a new ferrule crimped.

    Insulated bootlace ferrule | 1mm² | 8mm | crimp | red | 100 pcs | Sofamel APF-1,00/8 | 245120

    Insulated bootlace ferrule 1 mm², 8 mm tube, red, 100 pcs – Sofamel APF-1,00/8. Reliable termination of flexible wires for panels, automation and equipment.

    Published: 2026-11-12 · Data verified against the manufacturer datasheet: 2026-11-12

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Terminal block | electrical wire connector | universal | 3x0.2-4mm² | for all types of wires | WAGO | 221-413 | 4050821808442
    Code: WAGO 221-413

    Universal 3-wire terminal block, designed for fast, safe and neat connection of electrical wires. This connector is suitable for solid, stranded and flexible wires, therefore it is widely used both in household electrical installations and in professional installation work.

    The convenient lever system allows the wire to be connected very quickly: lift the lever, insert the conductor and lock it by lowering the lever. The connector has a transparent housing, making it easier to visually check whether the wire has been inserted correctly. 

    Price 0.33 € VAT incl.
    ( 0.27 € VAT excl. )
    Terminal clamp | electrical wire connector | universal | 2x0.2-4mm² | for all wire types | WAGO | 221-412 | 4050821808435
    Code: WAGO 221-412

    The WAGO 221-412 connector is one of the most popular and reliable electrical wire connection solutions in the world. It is designed for fast, safe, and professional connection of various types of copper conductors without the need for additional tools.

    Thanks to the patented CAGE CLAMP® technology and convenient orange levers, this connector allows quick connection of solid, stranded, and flexible conductors. The transparent housing enables visual inspection of the connection quality, while its compact dimensions allow easy installation in junction boxes, distribution boards, luminaires, and various automation equipment.

    The WAGO 221 series is widely used in residential, commercial, and industrial applications where reliable, standards-compliant, and long-lasting wire connections are required. 

    Price 0.30 € VAT incl.
    ( 0.25 € VAT excl. )
  • privacy policy

    Information