Products catalog

  • Insulated bootlace ferrule | 2.5mm² | 8mm | crimp | blue | 100 pcs | Sofamel APF-2,50W/8 | 246140

    Code: 246140
    Barcode: 8435157312997

    Insulated wire end ferrule 2.5 mm² for flexible wires, 8 mm tube, blue. Sofamel APF-2,50W/8, tin-plated copper, PA collar. 100 pcs per pack.

  • Insulated bootlace ferrule | 2.5mm² | 8mm | crimp | blue | 100 pcs | Sofamel APF-2,50W/8 | 246140

    The insulated ferrule terminates a flexible 2.5 mm² wire before it is connected to a screw or spring terminal. The strands are crimped in a tin-plated copper tube, and the insulating collar protects the wire entry.

    Key point:
    Unsecured strands of a flexible wire splay in the terminal, some break, and the contact weakens and heats up. The ferrule turns the strands into a solid pin – the connection stays reliable after vibration and temperature cycles.
    Cross-section
    2.5 mm²
    Tube length
    8 mm
    Colour
    blue
    Pack
    100 pcs

    Operating principle

    Strip the insulation to the ferrule tube length (8 mm), twist the strands and insert the wire fully – the wire insulation must enter the insulating collar.

    The ferrule is crimped with ferrule crimping pliers using a square or trapezoidal profile. The tube and strands are compressed into one solid pin.

    The crimped pin is inserted into the terminal and tightened to the equipment manufacturer's torque – the terminal clamps solid metal, not individual strands.

    Why choose Sofamel APF-2,50W/8?
    Tin-plated copper tube and PA collar; the blue colour (Sofamel W) identifies the cross-section at a glance, without measuring.

    Technical specifications

    Product typeInsulated bootlace ferrule (wire end ferrule)
    ManufacturerSofamel (Spain)
    ModelAPF-2,50W/8
    Manufacturer code246140
    EAN8435157312997
    Wire cross-section2.5 mm²
    Tube (pin) length8 mm
    Overall length15.2 mm
    Tube inner Ø2.2 mm
    Collar Ø4 mm
    Collar colourblue (colour code Sofamel W)
    Materialelectrolytic copper, tin-plated; insulating collar – polyamide (PA)
    Pack100 pcs
    CertificateUL

    Key functions

    • Strand compression – the terminal clamps the full cross-section, not individual strands.
    • Tin-plated copper – lower contact resistance and protection against oxidation.
    • Insulating collar – protects the wire entry and eases insertion.
    • Colour code – the cross-section is recognised at once during installation and panel inspection.
    • Exact tube length – 8 mm matches the terminal depth – no bare wire, no protruding pin.

    Where is it used?

    • Residential distribution boards
    • Automation and control panels
    • Screw and spring terminal blocks
    • Circuit breakers, RCDs, contactors
    • Controllers, relays, power supplies
    • Motor and equipment connection boxes

    Use by need

    Panel builder.
    Uniform, neat wire ends and faster panel inspection.
    Electrician.
    Flexible wires stay secure in terminals – no re-tightening needed.
    Maintenance technician.
    Fewer loose connections in vibrating equipment.

    Practical use

    If you connect a flexible 2.5 mm² wire to a circuit breaker in a panel, crimp a ferrule on it – the terminal clamps all strands and the joint does not need re-tightening at periodic inspection.

    Advantages

    • Strands do not splay or break in the terminal
    • Stable contact even under vibration
    • Tin-plated copper – protection against oxidation
    • Colour coding by cross-section
    • Pack of 100 pcs

    Disadvantages / limitations

    • For flexible wires only – not needed for solid wire
    • Requires ferrule crimping pliers – ordinary pliers do not crimp properly
    • Single use – after removal the wire end must be cut off
    • Tube length 8 mm – for a terminal of different depth choose another length

    Safety and installation notes

    • Switch off the voltage and verify it is absent before work.
    • Choose the ferrule exactly to the wire cross-section (2.5 mm²) – not larger, not smaller.
    • Crimp only with the intended tool and the correct die.
    • Do not use a badly crimped ferrule – cut it off and crimp a new one.
    • Tighten the terminal to the manufacturer's torque and check the wire with a pull test.

    Quick selection guide

    2.5 mm²
    8 mm
    blue
    100 pcs
    Sofamel APF-2,50W/8
    Suitable when you need:
    • to connect a flexible wire to a screw or spring terminal
    • a neat, easily inspected connection
    • reliable contact in vibrating equipment
    Check before use:
    • the wire cross-section (2.5 mm²)
    • the terminal depth and tube length (8 mm)
    • that you have ferrule crimping pliers
    Important reminder: A ferrule does not replace correct sizing of the wire and the protective device – it ensures a quality wire-end connection.

    FAQ

    Is a ferrule needed for solid wire?
    No – it is intended for flexible (stranded) wires.
    Which wire does this ferrule fit?
    A flexible 2.5 mm² wire.
    What do I crimp it with?
    Ferrule crimping pliers with a square or trapezoidal profile.
    How much insulation should be stripped?
    As long as the tube – 8 mm.
    What does the colour mean?
    The colour indicates the cross-section according to the Sofamel W colour code.
    Can the ferrule be reused?
    No – after removal the wire end must be cut off and a new ferrule crimped.

    Insulated bootlace ferrule | 2.5mm² | 8mm | crimp | blue | 100 pcs | Sofamel APF-2,50W/8 | 246140

    Insulated bootlace ferrule 2.5 mm², 8 mm tube, blue, 100 pcs – Sofamel APF-2,50W/8. Reliable termination of flexible wires for panels, automation and equipment.

    Published: 2026-11-12 · Data verified against the manufacturer datasheet: 2026-11-12

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

  • privacy policy

    Information