Products catalog

  • Insulated twin bootlace ferrule | 2×10mm² | 14mm | crimp | red | 100 pcs | Sofamel APF/D-10,00D | 255170

    Code: 255170
    Barcode: 8435157313383

    Insulated twin wire end ferrule 2 × 10 mm² for flexible wires, 14 mm tube, red. Sofamel APF/D-10,00D, tin-plated copper, PA collar. 100 pcs per pack.

  • Insulated twin bootlace ferrule | 2×10mm² | 14mm | crimp | red | 100 pcs | Sofamel APF/D-10,00D | 255170

    The insulated twin ferrule terminates two flexible 10 mm² wires in one terminal. Both wires are crimped in one tin-plated copper tube, so a single solid pin enters the terminal of a circuit breaker, relay or terminal block.

    Key point:
    Without a ferrule, two flexible wires in one terminal are rarely clamped evenly – over time one of them loosens and heats up. A twin ferrule joins both wires into one pin, so the bridge between devices stays reliable.
    Cross-section
    2 × 10 mm²
    Tube length
    14 mm
    Colour
    red
    Pack
    100 pcs

    Operating principle

    Strip the insulation to the ferrule tube length (14 mm), twist the strands and insert both wires fully – the wire insulation must enter the insulating collar.

    The ferrule is crimped with ferrule crimping pliers using a square or trapezoidal profile. The tube and strands are compressed into one solid pin.

    The crimped pin is inserted into the terminal and tightened to the equipment manufacturer's torque – the terminal clamps solid metal, not individual strands.

    Why choose Sofamel APF/D-10,00D?
    Tin-plated copper tube and PA collar; the red colour (DIN 46228-4) identifies the cross-section at a glance, without measuring.

    Technical specifications

    Product typeInsulated twin bootlace ferrule (wire end ferrule)
    ManufacturerSofamel (Spain)
    ModelAPF/D-10,00D
    Manufacturer code255170
    EAN8435157313383
    Wire cross-section2 × 10 mm²
    Tube (pin) length14 mm
    Overall length26 mm
    Tube inner Ø6.5 mm
    Collar colourred (colour code DIN 46228-4)
    Materialelectrolytic copper, tin-plated; insulating collar – polyamide (PA)
    Pack100 pcs
    CertificateUL

    Key functions

    • Strand compression – the terminal clamps the full cross-section, not individual strands.
    • Tin-plated copper – lower contact resistance and protection against oxidation.
    • Insulating collar – protects the wire entry and eases insertion.
    • Colour code – the cross-section is recognised at once during installation and panel inspection.
    • Two wires in one pin – bridges between devices without extra terminals.

    Where is it used?

    • Residential distribution boards
    • Automation and control panels
    • Screw and spring terminal blocks
    • Circuit breakers, RCDs, contactors
    • Controllers, relays, power supplies
    • Motor and equipment connection boxes

    Use by need

    Automation panel installer.
    Bridges between devices without extra terminals or busbars.
    Panel builder.
    Uniform, verifiable connections in series production.
    Maintenance technician.
    Fewer loose connections in vibrating equipment.

    Practical use

    If you need to bridge the supply of several circuit breakers, crimp two 10 mm² wires in one twin ferrule – each terminal then receives one pin and both wires are clamped evenly.

    Advantages

    • Strands do not splay or break in the terminal
    • Stable contact even under vibration
    • Tin-plated copper – protection against oxidation
    • Colour coding by cross-section
    • Pack of 100 pcs

    Disadvantages / limitations

    • For flexible wires only – not needed for solid wire
    • Requires ferrule crimping pliers – ordinary pliers do not crimp properly
    • Single use – after removal the wire end must be cut off
    • Tube length 14 mm – for a terminal of different depth choose another length

    Safety and installation notes

    • Switch off the voltage and verify it is absent before work.
    • Choose the ferrule exactly to the wire cross-section (2 × 10 mm²) – not larger, not smaller.
    • Crimp only with the intended tool and the correct die.
    • Do not use a badly crimped ferrule – cut it off and crimp a new one.
    • Tighten the terminal to the manufacturer's torque and check the wire with a pull test.

    Quick selection guide

    2 × 10 mm²
    14 mm
    red
    100 pcs
    Sofamel APF/D-10,00D
    Suitable when you need:
    • two flexible wires in one terminal
    • a neat, easily inspected connection
    • reliable contact in vibrating equipment
    Check before use:
    • the wire cross-section (2 × 10 mm²)
    • the terminal depth and tube length (14 mm)
    • that you have ferrule crimping pliers
    Important reminder: A ferrule does not replace correct sizing of the wire and the protective device – it ensures a quality wire-end connection.

    FAQ

    Is a ferrule needed for solid wire?
    No – it is intended for flexible (stranded) wires.
    Which wire does this ferrule fit?
    A flexible 2 × 10 mm² wire.
    What do I crimp it with?
    Ferrule crimping pliers with a square or trapezoidal profile.
    How much insulation should be stripped?
    As long as the tube – 14 mm.
    What does the colour mean?
    The colour indicates the cross-section according to the DIN 46228-4 colour code.
    Can wires of different sizes be combined?
    No – both wires must be 10 mm².

    Insulated twin bootlace ferrule | 2×10mm² | 14mm | crimp | red | 100 pcs | Sofamel APF/D-10,00D | 255170

    Insulated twin bootlace ferrule 2 × 10 mm², 14 mm tube, red, 100 pcs – Sofamel APF/D-10,00D. Reliable termination of flexible wires for panels, automation and equipment.

    Published: 2026-11-12 · Data verified against the manufacturer datasheet: 2026-11-12

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

  • privacy policy

    Information