Perforated angle bracket | sheet thickness | 1.5mm | 25x25 | L-2m | 620220 KTP25H25/2
Code: 620220Price 2.93 € VAT incl.( 2.42 € VAT excl. )The perforated angle bracket is a strong and versatile mounting element designed for fastening systems of electric racks, cabinets, enclosures, and cases. Made from high-quality galvanized steel, it ensures reliable and long-lasting use both indoors and outdoors. Thanks to regular perforations, the bracket allows for easy and quick installation work.
Important! For large order quantities, any section length up to 3 meters is available.
-
Perforated Angle Bracket | Sheet Thickness 1.5 mm | 25×25 mm | L=2 m | BAKS KTP25H25/2 | 620220
L-shaped steel profile with uniform perforation on both flanges – a compact and versatile mounting element for cable tray systems, electrical panel frames and racks. One component provides a firm, accurately positioned set of fixing points without additional drilling.
Key concept:
The perforated angle bracket KTP25H25/2 is primarily designed for the supporting structures of cable tray systems – wall and ceiling bracket frames, cable tray crossbeams, and panel/enclosure frame connections. The 1.5 mm sheet thickness with Sendzimir galvanizing provides adequate rigidity for light and medium loads, while the compact 25×25 mm profile fits where larger brackets are too bulky or unnecessary. The full 2 m length is easily cut with a hand saw or angle grinder to the required dimension.Legs 25×25 mm
Compact, flat flange – suitable for narrow structures and limited installation depthSheet thickness 1.5 mm
Sendzimir galvanized steel – corrosion protection compliant with PN-EN 10346:2015-09Length 2,000 mm
One profile – multiple support positions; easily cut to the required dimensionPerforation on both flanges
Bolt and rivet fixing without additional drilling – at fixed intervals along the entire lengthConstruction and Purpose
KTP25H25/2 is an equal-leg (symmetric) L-shaped steel profile where both 25 mm wide flanges are formed from a single 1.5 mm thick Sendzimir galvanized sheet steel blank. The perforation runs through both flanges along the full 2 m length at uniform intervals, so the fixing position is selected without measuring and drilling. BAKS classifies these angle brackets in the "Supporting and Mounting Elements" group, which is directly intended for joining and securing electrical enclosures, frames and cable tray system components.
The installation scheme is simple: the bracket is fixed to a wall, ceiling or another frame member with bolts through the flange perforations, and the second flange becomes the supporting surface for a cable tray, ladder section or enclosure part. Where the structure requires more sections, brackets are joined using a parallel node or overlap principle. Cutting to size with a hand metal saw, a metal disc cutter or an angle grinder.
Why is KTP25H25/2 useful?
The compact 25×25 mm profile offers a good compromise between rigidity and working space: where a larger bracket (35×35 or 50×50 mm) is too large or too heavy, KTP25H25/2 saves both material and space while maintaining adequate structural strength for light loads.Technical Specifications
td style="border:1px solid #cbd5e1; padding:9px;">2,000 mm (2 m)Product type Perforated angle bracket (L profile, equal-leg) Manufacturer BAKS Kazimierz Sielski (Poland) Manufacturer code / catalogue No. KTP25H25/2 / 620220 Flange dimensions (a × H) 25 × 25 mm (equal-leg) Sheet thickness 1.5 mm Length Material (standard version) Steel, Sendzimir galvanized – PN-EN 10346:2015-09 (S) Other surface treatment options F – hot-dip galvanizing (PN-EN ISO 1461); E – stainless steel; L – standard RAL colour painting Perforation Both flanges, at uniform intervals along the full length (BAKS standard pitch) Profile shape L (angle bracket, 90°) Purpose per BAKS Supporting elements for mounting electrical enclosures, frames and structures Box quantity 10 pcs (20 m) Key Features
- Perforation on both flanges – bolts, rivets and pins are fixed at any position without additional drilling; saves installation time and reduces error.
- Equal-leg L profile 25×25 mm – the symmetric bracket allows fixing from both sides or rotating 90°; suitable for narrow structures and limited depth.
- Sendzimir galvanizing – internal and external zinc corrosion protection; suitable for dry and normal-humidity interiors without additional coating.
- 2 m standard length – one profile covers multiple installation distances; easily cut without special tools to the required dimension.
- Compatible with BAKS cable tray system – the bracket is used as a support for cable trays, ladder sections and junction frames within the same system.
- Lightweight and manageable – the 1.5 mm wall provides adequate rigidity for light loads while keeping a small profile that is easy to transport and store.
Where is it used?
- Cable tray and ladder support – wall or ceiling bracket frame for cable tray; the angle bracket connects vertical posts with horizontal supports.
- Electrical panel and enclosure frame installation – bottom, top and side frame members in assembled structures.
- Rack and shelf framework – load shelf support beams in warehouses, server rooms, electrical rooms.
- Industrial automation – internal frame and DIN rail mounting base for control panels.
- HVAC and pipe supports – small metalwork and pipe support structures where simple angular connections are needed.
- Construction and fit-out work – light metal frame parts where a structural profile is not needed but clean perforation and a true right angle matter.
- Spare and repair material – kept in stock as a universal material for quick repair and top-up work.
Use by Application
For the electrical installation engineer.
Cable tray support, BAKS cable tray and ladder system frame – standard part of perforated and mesh tray installation without additional calculations.For the automation panel assembler.
Internal frame element, DIN rail holder, enclosure partition divider or bottom support pad – one profile performs multiple functions inside a panel.For the warehouse / industrial facility manager.
Quick metal connection for assembling racks, shelves or light-duty frames without welding – just cut and tighten the bolts.Practical application:
In an electrical room, a 200 mm BAKS cable tray section needs to be fixed to a concrete ceiling: two KTP25H25/2 brackets are cut to 300 mm, the ceiling plate is fixed through the upper flange (M8 anchor into concrete), and the lower flange becomes the support surface for the cable tray – in 15 minutes without drilling in the tray itself.Advantages
- Perforation on both flanges – fixing at any position without drilling
- Sendzimir galvanizing – effective corrosion protection in dry and normal-humidity interiors
- Versatile: cable tray supports, frames, racks, automation panel interiors
- Compatible within BAKS system with cable tray, ladder and bracket groups
- Easily cut to size – no special tools required
- 2 m length – rational storage and transport, less offcut waste
Limitations
- 1.5 mm wall – not designed for heavy loads; for medium and heavy structures choose KTC25H25/2 (2.0 mm) or KTP35H35/2 (35×35 mm)
- Standard version (S) – dry and normal-humidity interiors only; corrosive environments require the F (hot-dip galvanizing) or E (stainless steel) version
- No grease or special protective coating – check the appropriate treatment for outdoor use
- Perforation is factory-fixed – if a different pitch is needed, the profile cannot be modified
Installation Notes
- Wear safety glasses when cutting – metal shavings are sharp; deburr cut edges with a file or deburring tool.
- Load calculation – before designing a supporting structure, verify that the profile is used as intended: 1.5 mm KTP is designed for light, non-structural loads.
- Bolts and washers – use bolts of the correct diameter for the perforation hole size; an oversized bolt can deform the flange.
- Corrosive environment – if ambient humidity is high or outdoor use is intended, order the F (hot-dip galvanizing) version; the standard S version is not suitable.
- Electrical installation structures – verify earthing and potential equalisation requirements against the applicable standard (e.g. PN-EN IEC 61439); the zinc coating maintains electrical conductivity, but joint reliability must be confirmed by the designer.
Quick Selection Guide – BAKS Angle Bracket Series
Selection depends on flange width, sheet thickness and load. Below are the main variants in this series:
Model Flanges Thickness Typical purpose KTP25H25/2 ← you are here 25×25 mm 1.5 mm Light cable tray supports, enclosure interior, small frame parts KTC25H25/2 25×25 mm 2.0 mm Same size, higher load – more reliable joint KTP35H35/2 35×35 mm 1.5 mm Larger flange – tray and enclosure supports, universal frames KTT50H50/2 50×50 mm 3.0 mm Heavy-duty structures, industrial frames, high loads Suitable when you need:- A compact, simple corner fixing element for a cable tray, enclosure or rack
- Fast assembly of a frame from standard BAKS profiles without cutting larger sections
- Stock material – one length cut as needed
Check before use:- Whether the 1.5 mm wall meets your structure's load requirements
- Whether ambient humidity permits the standard S (Sendzimir) version
- Whether the 25 mm flange is wide enough for your joining component
Important reminder: KTP25H25/2 does not replace structural steel profiles (e.g. IPE, UPE, L-angles per EN 10056) – it is an electrical installation auxiliary material for light supports and frames.Frequently Asked Questions
⚡What is the difference between KTP25H25/2 and KTC25H25/2?
KTP – 1.5 mm sheet thickness, KTC – 2.0 mm; both series have the same 25×25 mm flange dimension, but KTC withstands higher loads and is more resistant to mechanical impact.⚡Can this angle bracket be used outdoors?
The standard S version (Sendzimir galvanizing) is not designed for long-term outdoor use – choose the F (hot-dip galvanizing) or E (stainless steel) version; these are supplied on order basis.⚡What bolt diameter fits the perforation?
The standard BAKS perforation hole is for an M8 bolt; check the exact diameter in the manufacturer's data sheets or physically on the product – if in doubt, contact us.⚡Can I order a 3 m length?
The KTP25H25 series comes in standard lengths of 2 m and 3 m; the 3 m variant can be supplied on order – contact us for availability.⚡How many angle brackets are needed for a standard cable tray bracket?
A typical wall-mounted bracket frame for a cable tray uses 2 angle brackets per support point (one on each side); the exact number depends on the tray width and span distance.⚡Can you select all support system components together?
Yes – send us the tray type, width and span distance: we will select the angle brackets, cross-arm supports and fixing elements and provide a complete proposal.Perforated Angle Bracket BAKS KTP25H25/2 | 1.5 mm | 25×25 mm | L=2 m | 620220
Compact L-shaped Sendzimir galvanized steel profile with perforation on both flanges – a universal material for cable tray supports, electrical panel frames and racks where an accurate fixing pitch without additional drilling matters. For light and medium loads in dry and normal-humidity interiors; for corrosive environments choose the F (hot-dip galvanizing) or E (stainless steel) version.
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.ManufacturerThis product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products
Rechargeable LED work light | 1500lm | IP65 | 3,7V/5Ah | Brennenstuhl RUFUS 1500 MA | 1173100100Code: 1173100100Mobile LED work floodlight designed for reliable workplace lighting in areas where there is no permanent power supply. Thanks to its 1500 lm luminous flux, rechargeable 5 Ah lithium-ion battery, IP65 protection rating and durable metal housing, this light is ideal for use on construction sites, in workshops, garages, warehouses, technical rooms, outdoor work and emergency situations.
The floodlight has 5 lighting modes, allowing the light intensity to be adjusted according to working conditions. The integrated Powerbank function allows a smartphone, tablet or other USB device to be charged via the USB port. The robust housing, protection against dust and water jets, and impact resistance make this model suitable for intensive everyday use.
Price 42.10 € VAT incl.( 34.79 € VAT excl. )Extension cable reel | extension cord with socket outlets | 3xSchuko | 40m | RR-F 3x1.5 | IP44 | Brennenstuhl | Garant | DSS | 1198470 | 4007123081356Code: 4007123081356Cable reel extension lead – a professional extension cord with 3 earthed Schuko socket outlets, designed for outdoor work, construction sites, workshops, garages, garden areas and other locations where reliable power supply over a longer distance is required.
This extension reel stands out with its high-quality Bremaxx cable, specially designed for demanding operating conditions: it remains flexible even down to -35 °C and is resistant to oils, acids, mechanical stress and more humid environments. The IP44 protection rating allows the extension lead to be used outdoors when additional protection against splashes and dust is required.
Price 106.48 € VAT incl.( 88.00 € VAT excl. )









