Products catalog

  • Supply air ventilation damper in wall | with filter | polyethylene foam thermal insulation | D125 | 0,95m | white | 12,5TOV095-03

    Code: 23073

    Wall-mounted supply air vent D125 with a 950 mm cuttable duct, G3 filter and thermal and acoustic insulation (closed-cell polyethylene foam). Flow is adjusted with a handle smoothly down to full closure; one vent is intended for a room of approximately 20 m².

  • Supply air ventilation damper in wall | with filter | polyethylene foam thermal insulation | D125 | 0,95m | white | 12,5TOV095-03

    Wall-mounted supply air vent (damper) D125 for bringing fresh outdoor air into residential and office rooms through an external wall. Duct length – 950 mm, thermal and acoustic insulation – closed-cell polyethylene foam. Airflow is adjusted with a handle on the indoor head – smoothly, down to full closure.

    Key idea:
    Airtight homes with PVC windows often lack fresh air: windows fog up, moisture and CO₂ build up. This vent supplies outdoor air in a controlled way – through a G3 filter, an insulated duct and with adjustment down to full closure, without replacing windows or installing ductwork. One vent is rated for a room of approximately 20 m².
    Duct length
    950 mm (can be cut)
    Insulation
    polyethylene foam
    Filter
    G3, washable
    Room
    up to ~20 m²

    Operating principle

    A hole is drilled in the wall with a Ø132 mm core bit (resulting hole ~133 mm) with a 2–3° slope towards the outside so that condensate drains outdoors. The plastic duct is cut to the wall thickness and inserted, and an aluminium grille with a stainless steel mesh is fixed outside.

    Outdoor air enters through the grille, passes the insulated duct and is distributed into the room through the G3 filter and the indoor head with damper. The insulation (polyethylene foam) reduces heat loss through the duct walls and dampens street noise.

    You adjust the flow with the handle on the head (or with a cord if mounted high), and a scale shows the opening degree. The vent works naturally – air flows due to the pressure difference, so it performs best when exhaust ventilation is running in the home (bathroom, kitchen).

    What does the 12,5TOV095-03 vent give you?
    You get controlled fresh air supply to a specific room without open windows or complex ductwork – with a filter against dust and insects, an insulated duct and the option to close it fully in cold weather.

    Technical specifications

    Product type Supply air ventilation damper (wall vent)
    Product code 12,5TOV095-03
    Nominal diameter D125
    Duct outer diameter 132 mm
    Wall opening Ø132 mm core bit (hole ~133 mm), 2–3° slope outwards
    Duct length 950 mm (cut to wall thickness)
    Series lengths 400–1000 mm in 50 mm steps
    Thermal and acoustic insulation closed-cell polyethylene foam
    Filter G3 class, in the head, washable with water
    Flow adjustment Handle on the head or cord, with scale; smooth down to full closure
    Outdoor part Aluminium grille with stainless steel mesh
    Throughput, fully open 61.0 m³/h at 1.5 m/s · 81.4 m³/h at 2 m/s · 122.1 m³/h at 3 m/s air velocity in the duct
    Recommended room area up to ~20 m² per vent
    Colour (indoor head) White
    Scope of delivery Indoor head with filter and damper, insulating element, plastic duct, outdoor grille

    Main functions

    • Adjustment down to full closure – adapt the flow to the weather and season, close the vent on cold days.
    • G3 filter in the head – captures dust, fluff and insects; removable and washable with water.
    • Insulated duct – the insulation (polyethylene foam) reduces heat loss and cooling of the duct walls.
    • Noise reduction – the insulation reduces street noise travelling through the duct.
    • Scale and cord – see the opening degree and operate a high-mounted vent with a cord.
    • Duct cut on site – fits walls of various thicknesses up to 950 mm – cut to the actual thickness.
    • Outdoor grille with mesh – aluminium grille with stainless steel mesh protects the duct from birds and coarse debris.

    Where is it used?

    • Bedrooms and children’s rooms lacking fresh air at night
    • Apartments with airtight PVC windows
    • Apartment blocks under renovation when windows are replaced
    • Private houses with natural or mechanical exhaust
    • Offices, studies, meeting rooms
    • Country houses and seasonal homes
    • Living rooms where windows fog up and moisture accumulates

    Use by need

    For the apartment owner.
    Solves stuffiness and window fogging in the bedroom without replacing windows or installing a heat recovery unit.
    For the renovation contractor.
    One D125 model fits walls of different thicknesses – the duct is cut on site, drilled with a standard Ø132 mm core bit.
    For the ventilation designer.
    A supply air element for living rooms where exhaust is arranged in the bathroom and kitchen.

    Practical use

    If bedroom windows (~14 m², PVC windows) fog up in the morning and the external wall is no thicker than 950 mm, one 12,5TOV095-03 vent is enough: the duct is cut to the wall thickness, the vent is mounted 20–30 cm from the window edge at a height of 2–2.5 m and left slightly open at night. Exhaust must run in the bathroom and kitchen – then air moves from the bedroom towards the wet rooms.

    Pros

    • Smooth adjustment down to full closure
    • G3 filter, washable with water
    • Closed-cell polyethylene foam insulation
    • Duct cut to wall thickness
    • Aluminium outdoor grille with stainless steel mesh
    • Operated by handle or cord, with scale
    • No electricity or ductwork needed

    Cons / limitations

    • Works naturally – flow depends on exhaust and weather, there is no fan
    • No heat recovery – outdoor-temperature air is supplied in winter
    • G3 is a coarse filter, not intended for fine particles (PM2.5)
    • In bathrooms, kitchens, vestibules and corridors a supply vent is not enough – exhaust is required there
    • Duct 950 mm – for a thicker wall choose a longer model of the series

    Safety and installation notes

    • Before drilling, check the wall for electrical cables, pipes and reinforcement.
    • Drill with a 2–3° slope outwards – otherwise condensate will run into the room.
    • Do not install close to the window reveal or at the junction of two external walls – the wall is coldest there, freezing and condensation may occur.
    • Fix the outdoor grille with louvres horizontal and sloping down, ideally under a canopy, window sill or eave – so water does not enter the duct.
    • Slide the insulation towards the head so that it does not obstruct the damper opening and closing.
    • Fix the inner part of the head with 4 dowels and screws with the arrow above a mounting hole pointing vertically down; the cord must not wind onto the adjustment mechanism.
    • In apartment blocks, agree façade drilling with the building administrator or owners’ association.

    Quick selection guide

    D125
    Duct 950 mm
    polyethylene foam
    G3 filter
    Up to ~20 m²
    Suitable when you need:
    • Fresh air in a bedroom, children’s room or study
    • A solution for fogging windows in an airtight apartment
    • A simple supply element without electricity
    Check before use:
    • Wall thickness – the duct (950 mm) must not be shorter than the wall
    • Whether exhaust ventilation runs in the home (bathroom, kitchen)
    • Space 20–30 cm from the window at 2–2.5 m height
    • Whether façade drilling is allowed (approval in apartment blocks)
    Important reminder: A supply vent does not replace exhaust ventilation or a heat recovery unit – it only supplies air and does not recover heat.

    FAQ

    What wall thickness does 12,5TOV095-03 fit?
    Walls up to 950 mm – the duct is cut to the actual wall thickness.
    What hole diameter is needed?
    A Ø132 mm core bit – giving a hole of about 133 mm, drilled with a 2–3° slope outwards.
    Can the vent be closed completely?
    Yes, the handle on the head adjusts the flow smoothly down to full closure.
    How often should the filter be cleaned?
    Washing the filter every 3 months, vacuuming the duct every 6 months and cleaning the grille once a year is recommended.
    What room size does one vent cover?
    The vent is rated for a living room of approximately 20 m².
    Is it suitable for bathroom or kitchen ventilation?
    No – exhaust ventilation is installed there, while the supply vent is fitted in living rooms.

    Supply air ventilation damper in wall | with filter | polyethylene foam thermal insulation | D125 | 0,95m | white | 12,5TOV095-03

    12,5TOV095-03 – wall-mounted supply air vent D125 with a 950 mm duct, G3 filter and thermal and acoustic insulation (polyethylene foam). Adjustable down to full closure, intended for a living or office room of up to ~20 m² with working exhaust.

    Published: 2026-11-04 · Data verified against the manufacturer datasheet: 2026-11-04

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Window trickle vent | adjustable | with G3 filter | 350 mm | white | no-drill installation | 350LVB
    Code: 37611

    350LVB – adjustable supply window trickle vent with G3 (EU3) filter: 350 mm long, 17.9 mm wide, white. Mounted on the sash of a PVC or wooden window without drilling the frame, fully closable with a slider.

    Price 25.41 € VAT incl.
    ( 21.00 € VAT excl. )
  • Subscribtion to new arrivals

    privacy policy

    Information