Products catalog

  • Axial exhaust fan with backdraft damper | D150 | 250 m³/h | 220V | 205x187x86 mm | plastic | white | IPX4

    Code: ESLP22738

    Axial exhaust fan with backdraft damper, Ø150 mm: 250 m³/h, 38 dB(A), 16 W, IPX4, 205×187×86 mm. The backdraft damper stops cold air and odours from returning from the duct.

  • Axial exhaust fan with backdraft damper | D150 | 250 m³/h | 220V | 205x187x86 mm | plastic | white | IPX4

    Axial exhaust fan for a Ø150 mm duct with a built-in automatic backdraft damper. Designed to remove moisture and odours from a bathroom, toilet, kitchen or storeroom when the duct must stay closed while the fan is off. The ultra-thin 9 mm front panel allows the fan to be mounted almost flush with the wall or tiles.

    Key point:
    When the fan stops, the backdraft damper closes the duct, so cold air, odours and dust from the shaft do not enter the room. Rated capacity is 250 m³/h, noise level 38 dB(A), power 16 W.
    Mounting diameter
    Ø150 mm
    Capacity
    250 m³/h
    Noise
    38 dB(A)
    Power
    16 W

    How it works

    The fan is inserted into a Ø150 mm duct or opening in a wall or ceiling; the 9 mm front panel stays almost flush with the finish. Supply is 220–240 V / 50 Hz. It is switched on by an external switch.

    When switched on, the impeller extracts air into the ventilation duct – up to 250 m³/h in free-air conditions, static pressure 54 Pa. The air flow opens the backdraft damper; when the fan stops, the damper closes and blocks back-draught.

    The result is a room that dries faster and a lower risk of condensation and mould.

    Why choose ESLP22738?
    The fan extracts air and closes the duct when idle – cold air and odours from the shaft do not come back. This matters in apartment buildings and houses with a shared or long ventilation shaft.

    Technical specifications

    Product type Axial exhaust fan with backdraft damper
    Product code ESLP22738
    Mounting (duct) diameter Ø150 mm
    Supply voltage 220–240 V / 50 Hz
    Power 16 W
    Current consumption 0.07 A
    Air flow (capacity) 250 m³/h
    Static pressure 54 Pa
    Noise level 38 dB(A)
    Dimensions 205×187×86 mm
    Protection rating IPX4
    Control external switch
    Backdraft damper built-in, closes automatically when the fan stops
    Front panel 9 mm thick (ultra slim)
    Housing plastic, white
    Mounting wall or ceiling

    Main functions

    • Automatic backdraft damper – the duct closes when the fan stops, keeping cold air, odours and dust out of the room.
    • 9 mm front panel – the fan can be mounted almost flush with the wall or tiles.
    • 250 m³/h capacity – rated air flow for air exchange in a small or medium-sized room.
    • 38 dB(A) noise level – as stated in the supplier specification, suitable for domestic rooms.
    • IPX4 housing – protected against water splashes from any direction.
    • Versatile mounting – in a wall or ceiling.

    How the models in this series differ

    • ESLP22737 · basic – basic version, controlled by an external switch
    • ESLP22738 · with backdraft damper – automatic backdraft damper – this model
    • ESLP22739 · with pull-cord switch – pull-cord switch on the housing
    • ESLP22740 · with cable and plug – power cable with plug
    • Series sizes – D100 – 90 m³/h, 14 W, 35 dB(A), 160×140×76 mm · D125 – 140 m³/h, 16 W, 36 dB(A), 180×160×82 mm · D150 – 250 m³/h, 16 W, 38 dB(A), 205×187×86 mm

    Where is it used?

    • Bathrooms and showers
    • Toilets
    • Kitchens and utility rooms
    • Storerooms and walk-in wardrobes
    • Basements and service rooms
    • Laundry rooms
    • Small sanitary rooms in offices

    Use by need

    For apartment owners in multi-storey buildings.
    The damper keeps out odours and cold air from the shared shaft.
    For electricians.
    Standard Ø150 mm duct, simple connection and a damper already built in.
    For country house owners.
    When the house is unheated or the fan is off, the closed duct keeps cold air out.

    Practical use

    If a bathroom measures 2.0 × 2.5 m with a 2.5 m ceiling (about 12.5 m³), the rated flow of 250 m³/h would theoretically change the air about 20 times per hour. In practice the flow will be lower due to duct length, bends and grilles, so for a long or winding duct a higher-capacity model is worth choosing.

    Pros

    • Built-in automatic backdraft damper
    • Ultra-thin 9 mm front panel
    • Wall or ceiling mounting
    • IPX4 protection
    • Power – 16 W

    Cons / limitations

    • Controlled by an external switch – no automatic switching by humidity
    • The rated 250 m³/h flow is given without duct resistance; in a long duct it is lower
    • No heat recovery – room air is exhausted

    Safety and installation notes

    • Disconnect the power before installation and make sure the circuit is de-energised.
    • Protect the bathroom circuit with a 30 mA residual current device (RCD).
    • IPX4 means splash protection, not immersion: do not install in zone 0 and follow the zone requirements of HD 60364-7-701.
    • Make sure the backdraft damper opens and closes freely – the duct or sealant must not press on it.
    • Mains installation must be carried out by a qualified electrician.

    Quick selection guide

    Ø150 mm
    250 m³/h
    38 dB(A)
    16 W
    IPX4
    Backdraft damper
    Suitable when you need:
    • To extract moisture from a bathroom or toilet
    • To stop cold air and odours coming back from the duct
    • A slim front panel almost flush with the wall
    Check before use:
    • Whether the duct or opening diameter is Ø150 mm
    • Whether there is room for the 205×187×86 mm housing
    • Whether a 220–240 V supply is available at the opening
    • Whether the room has an air inlet path (gap under the door or a grille)
    Important reminder: The fan does not replace continuous mechanical ventilation or a heat recovery unit – it extracts air only while running.

    FAQ

    What is the backdraft damper for?
    When the fan stops it closes the duct so that cold air and odours do not enter the room.
    What duct diameter does ESLP22738 fit?
    A Ø150 mm duct or opening.
    Can it be mounted in the ceiling?
    Yes, the fan can be mounted in a wall or ceiling.
    Does it have a timer or humidity sensor?
    No, this model is controlled by an external switch.
    What is special about the front panel?
    It is only 9 mm thick, so the fan looks almost flush with the wall or tiles.
    Is it suitable for a bathroom?
    Yes, the housing is IPX4, but install it outside zone 0 and protect the circuit with a 30 mA RCD.

    Axial exhaust fan with backdraft damper | D150 | 250 m³/h | 220V | 205x187x86 mm | plastic | white | IPX4

    ESLP22738 – axial exhaust fan with backdraft damper Ø150 mm: 250 m³/h, 38 dB(A), 16 W, IPX4. The backdraft damper stops cold air and odours from returning from the duct.

    Published: 2026-11-13 · Data verified against the supplier specification: 2026-11-13

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Flexible aluminum air duct | for ventilation | ventilation systems | D100mm | 3m | white | LAO100B
    Code: 23033

    Flexible aluminium air duct - a reliable and universal solution for professional and residential ventilation systems. Designed to connect ventilation elements, fans, heat recovery components or other air distribution units.

    Due to its low weight, high flexibility and resistance to high temperatures, the duct ensures quick installation, tightness and long-term operation even in more demanding conditions. The white surface blends aesthetically in technical and visible installation areas. 

    Price 7.20 € VAT incl.
    ( 5.95 € VAT excl. )
    Supply air ventilation damper in the wall | with filter | mineral wool thermal insulation with foil | D125 | 0,45m | white | 12,5TOV045-01
    Code: 23041

    Wall supply air valve Ø125 mm / 450 mm with filter, non-return valve and foil-faced mineral wool insulation. Restores fresh air supply in apartments, houses and offices, dampens street noise, while the foil protects the wool from moisture and dust.

    Price 31.45 € VAT incl.
    ( 25.99 € VAT excl. )
    Duct centrifugal fan | D125 | 370 m³/h | 52 W | 230 V | 310 Pa | plastic housing | white | 15622
    Code: 15622

    Duct centrifugal fan 15622: D125, up to 370 m³/h, 310 Pa, 52 W, 230 V, plastic housing.

    Price 93.17 € VAT incl.
    ( 77.00 € VAT excl. )
    Shut-off damper for round air duct | for ventilation | air handling systems | D100 | silver | galvanized steel | 100USO
    Code: 04963

    Round duct shut-off damper, designed to shut off, restrict, or regulate airflow in round air ducts. The damper is used in supply, exhaust, or recirculation air systems where simple and efficient control of air movement within premises is required.

    Due to its galvanized steel construction, the product is resistant to corrosion, durable, and suitable for use in residential, commercial, and technical ventilation systems. Manual operation allows easy airflow adjustment without the need for an additional electric actuator or automation system. 

    Price 6.50 € VAT incl.
    ( 5.37 € VAT excl. )
  • Subscribtion to new arrivals

    privacy policy

    Information