Products catalog

Home/Product Catalog/Automation and Control Systems/Control components for automation and control systems/Trolleys | Crane Control Panels | Hoist Control | Joystick/Industrial crane control panels | wired control solutions
  •   Crane control pendant | with 2 buttons | 1-speed | 5A | 120–400V | IP54 | IEK | BPU10-2 | 4606056040302
      Crane control pendant | with 2 buttons | 1-speed | 5A | 120–400V | IP54 | IEK | BPU10-2 | 4606056040302 1

    Crane control pendant | with 2 buttons | 1-speed | 5A | 120–400V | IP54 | IEK | BPU10-2 | 4606056040302

    Code: BPU10-2
    Barcode: 4606056040302
    Inquire about this item
    Price 15.46 € VAT incl.
    ( 12.78 € VAT excl. )
    Want another price? Suggest yours!
    This control pendant is designed for simple 2-command hoisting mechanism control, where single-speed buttons and mechanical interlocking are required. The IP54 housing, protective cable gland, and sealing gasket help protect the inside of the pendant from dust and moisture ingress.
  • Product description

     

    Crane control pendant  – 2 buttons, 1 speed, 5A, 120–400V, IP54

    Crane control pendant is designed for switching control circuits of lifting mechanisms, hoists, electric hoists, cranes and other electrical control systems. This is a 2-button, 1-speed pendant control unit with a sealed IP54 housing made of heat-resistant ABS plastic. The pendant is used for manual motion control, for example forward / reverse, up / down or other two-direction control functions according to the specific electrical diagram.

    Main idea:
    This control pendant is intended for simple 2-command control of a lifting mechanism when single-speed buttons and mechanical interlocking are required. The IP54 housing, protective cable gland and sealing gasket help protect the inside of the pendant from dust and moisture ingress.
    Buttons
    2 controls
    Speeds
    1 speed
    Current
    5 A
    Protection
    IP54

    Operating principle

    The push-button crane control pendant is used to switch electrical control circuits. When a button is pressed, the pendant sends a control signal to a contactor, relay, control circuit or another device that performs the mechanism movement according to the wiring diagram.

    This model has 2 controls and is designed for 1-speed control. The buttons are self-resetting, so when the button is released, it returns to its original position. Mechanical interlocking helps prevent opposite commands from being activated at the same time, for example when movement in both directions must not be switched on simultaneously.

    What is a 2-button 1-speed pendant used for?
    Such a pendant is most often used for simple two-direction mechanism control: up / down, forward / reverse, left / right or other two commands according to the specific lifting or control system diagram. The single-speed design means that one control stage is provided for each direction.

    Technical parameters

    Product type Crane / lifting mechanism control pendant
    Manufacturer IEK
    Model / code BPU10-2
    EAN code 4606056040302
    Number of controls 2
    Number of speeds 1 speed
    Type of movement performed Other / according to the electrical control diagram
    Housing material Heat-resistant ABS plastic
    Housing properties Non-flammable plastic, sealed housing with built-in buttons
    Width 68 mm
    Height 50 mm
    Depth 223 mm
    Length 253 mm
    Rated voltage 120 / 230 / 400 V
    Frequency 50 Hz
    Operating temperature -25 ... +45 °C
    Control button functions Start forward / reverse Stop according to the specific wiring diagram
    Conventional thermal current 5 A
    Rated operational current AC-15, 120 V 6.0 A
    Rated insulation voltage Ui 500 V
    Rated impulse withstand voltage 4 kV
    Rated conditional short-circuit current Icn 1000 A
    Short-circuit current protection at Ie 3A, gG/qG fuse 5.0 A
    Short-circuit current protection at Ie 1.5A, gG/qG fuse 3.0 A
    Model / operation Push-on self-reset
    Interlocking Mechanical
    Operating force 30 N
    Mechanical wear resistance 30,000 cycles
    Protection rating IP54
    Cross-section of connected conductors ≤ 1.5 mm²
    Environmental use B
    Internal cable size 16 mm
    Service life Not less than 15 years
    Warranty period 3 years
    Compliance CE requirements, certification tests and serial production conformity certificates according to the provided information

    Where is it used?

    • In lifting mechanisms – for switching electrical control circuits.
    • In electric hoists and hoists – for simple 2-direction control according to the specific diagram.
    • In cranes – for manual control of movement commands.
    • In industrial equipment – when a pendant push-button control unit is required.
    • In workshops, warehouses and technical zones – for mechanisms, gates, lifting equipment or other control circuits.

    Practical installation example

    For example, the pendant is suspended near the control position of the lifting mechanism. The cable is inserted through the protective gland, which helps prevent dust and moisture from entering the housing. Inside, the buttons are connected to the control circuit, contactors or relay control elements according to the specific equipment diagram.

    The operator presses one of the two buttons to activate the selected movement direction. When the button is released, it returns to its original position, while mechanical interlocking helps prevent incorrect activation of opposite commands at the same time.

    Advantages

    • 2-button control – suitable for simple two-direction mechanism control.
    • 1-speed design – clear and simple control without additional speed stages.
    • IP54 housing – protection against dust and water splashes.
    • ABS plastic housing – lightweight, strong and heat-resistant solution.
    • Protective cable gland – helps seal the cable entry.
    • Mechanical interlocking – helps prevent opposite commands from being activated simultaneously.
    • Self-resetting buttons – convenient for control circuits where the command must operate only while the button is pressed.
    • CE compliance – according to the provided information, the pendant complies with CE requirements.

    Disadvantages / limitations

    • Only 2 buttons – not suitable for more complex multi-direction or multi-function control.
    • Only 1 speed – not suitable for systems where two-speed control is required.
    • 5 A thermal current – intended for control circuits, not for direct supply of high-power motors.
    • IP54 is not full outdoor sealing – in open environments, rain, dust, mechanical impact and cable sealing must be evaluated.
    • A suitable wiring diagram is required – functions depend on how the pendant is connected to the control circuit.

    Safety and installation notes

    The crane control pendant is a component of an electrical control circuit, therefore before installation it is necessary to evaluate the control voltage, contact current, cable cross-section, mechanism control logic, safety circuits and operating environment.

    • Installation must be carried out by a qualified electrician or automation specialist, in accordance with electrical and lifting equipment safety requirements.
    • The pendant is intended for control circuits – contactors, relays or other power control devices are required for direct motor or high-power load control.
    • The rated contact parameters must not be exceeded – current, voltage and load type limits must be observed.
    • The cable entry must be tightly secured to maintain the housing protection against dust and moisture.
    • When used with lifting equipment, the operation of emergency stop, limit switches and other safety circuits must be checked.

    Quick selection guide

    This is a suitable choice when a 2-button, 1-speed crane or lifting mechanism control pendant with IP54 protection, ABS plastic housing, protective cable gland and self-resetting buttons is required. The pendant is intended for control circuits, not for direct supply of high-power loads.

    Buttons
    2 controls
    Speeds
    1 speed
    Current
    5 A
    Protection
    IP54
    Suitable when you need to:
    • control lifting mechanism movement in two directions;
    • use a single-speed control pendant;
    • connect the pendant to contactors or a control circuit;
    • have a pendant control unit with an IP54 housing;
    • use the pendant for hoists, electric hoists, cranes or technical mechanisms.
    Check before installation:
    • whether 2 buttons are sufficient for the specific mechanism;
    • whether 1 speed is required, not 2-speed control;
    • whether the control circuit voltage matches the pendant parameters;
    • whether the contact current is sufficient for the control circuit;
    • whether an additional STOP or emergency stop button is required;
    • whether the cable entry and sealing will be properly installed.
    Important reminder:
    This pendant is intended for control circuits. The motor of a lifting mechanism or another higher-power load must not be connected directly through the pendant if the load exceeds the contact parameters of the pendant. In such cases, contactors, relays and suitable safety circuits are used.

    FAQ – frequently asked questions

    What is this crane control pendant intended for?
    It is intended for switching electrical control circuits of lifting mechanisms, cranes, hoists, electric hoists or other equipment.
    How many buttons does this model have?
    This model has 2 controls / buttons.
    Is the pendant single-speed?
    Yes, this model is designed for 1-speed control.
    Is the pendant suitable for directly connecting a motor?
    Usually not. The pendant is intended for control circuits. Contactors, relays or other power control devices are usually used to control a motor or a higher load.
    What does IP54 mean?
    IP54 means protection against dust levels that could interfere with device operation and protection against water splashes. Actual protection depends on correct cable entry and housing sealing.
    Are the buttons self-resetting?
    Yes, the specified operation is Push-on self-reset, so when the button is released, it returns to its original position.
    Can more buttons be installed?
    PKT / BPU series pendants may have 2, 4 or 6-button versions, but this specific model is a 2-button version.

    Simple and reliable lifting mechanism control

    The crane control pendant provides clear 2-button control for single-speed lifting mechanisms, hoists, electric hoists and other technical systems.

    Thanks to the IP54 housing, ABS plastic construction, protective cable gland, mechanical interlocking and self-resetting buttons, this pendant is a practical solution for control circuits in industry, warehouses, workshops and technical zones.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.

  • Alternative products

    Copper installation cable NYM | 2×1.5 mm² no PE | 300/500 V | white | 1 m | Lietkabelis KH05VV-U 2x1.5 New item  
    Copper installation cable NYM | 2×1.5 mm² no PE | 300/500 V | white | 1 m | Lietkabelis KH05VV-U 2x1.5
    Code: 92021501
    Price 0.67 € VAT incl.
    ( 0.56 € VAT excl. )
    Add to cart 

  • Subscribtion to new arrivals

    privacy policy

    Information