Three-phase voltage and current relay | 3F+N | 63 A | phase sequence | DIN | EL-AVR-XXTF
Code: EL-AVR-XXTFPrice 80.34 € VAT incl.( 66.40 € VAT excl. )The EL-AVR-XXTF is a three-phase digital voltage relay that monitors the voltage of each phase and disconnects the load directly through its contacts.
-
Three-phase voltage and current relay | 3F+N | 63 A | phase sequence | DIN | EL-AVR-XXTF
The EL-AVR-XXTF is a three-phase digital voltage relay that monitors the voltage of each phase and disconnects the load directly through its contacts. In addition to voltage, it measures the load current and disconnects the circuit when the set limit is exceeded.
Key point:
One relay protects the whole three-phase supply or three-phase equipment: each phase is monitored separately and the load is disconnected automatically in case of a network fault.Load current
63 ANetwork / supply
3F+N, 3×380 V ACFunctions
phase sequence, current limitHow it works
The relay is connected to the three-phase supply (with neutral, depending on the model); the voltage of each phase is measured separately.
When the voltage in any phase leaves the limits, the load is disconnected; depending on the model, asymmetry, phase sequence or phase loss are also monitored. When the set current limit is exceeded, the load is also disconnected – this limits the power drawn.
When the parameters return to normal, the load is reconnected after the set delay.
Why choose the EL-AVR-XXTF?
One device instead of several single-phase relays – less space in the board and a clear view of each phase.Technical specifications
Product type Three-phase digital voltage and current relay (power type) Manufacturer / code EL-AVR-XXTF Network 3F+N, 3×380 V AC Rated current 63 A Own consumption < 6 W Display / indication LED 3 × 6 digits Measuring accuracy ±1 % Operating temperature −20…+55 °C Mounting DIN 35 mm Main functions
- Monitoring of each phase – a fault is detected in any phase.
- Over- and undervoltage protection – appliances are disconnected when the neutral breaks or the network fails.
- Current limit – an overloaded circuit is disconnected, the power drawn is limited.
- Phase sequence monitoring – the motor is not started with swapped phases.
- Neutral loss monitoring – reacts to a broken neutral conductor.
- Digital display or indication – the status is visible at once.
Where is it used?
- Three-phase supplies of houses and country homes
- Workshops, garages, farm buildings
- Three-phase pumps, compressors, machine tools
- Heat pumps with three-phase supply
- Small production and storage premises
Use by need
For the owner of a three-phase house.
One relay monitors all phases.For a workshop or farm owner.
Three-phase equipment is disconnected on network faults.For the electrician.
One device instead of several – fewer connections in the board.Practical use
A workshop has a three-phase supply: machine tools and compressor are three-phase, lighting and sockets single-phase. If one phase fails, the EL-AVR-XXTF disconnects the load and reconnects it automatically when the parameters return.Pros
- Monitors each phase
- Automatic reconnection
- One device instead of several
- DIN mounting
Cons / limitations
- Does not protect against lightning and short surges – an SPD is needed
- Does not replace circuit breakers and RCDs
- IP20 – dry board only
- The manufacturer does not publish a full datasheet – parameters per supplier specification
Safety and installation notes
- Install only after disconnecting the supply; work must be done by a qualified electrician.
- Upstream – a circuit breaker with a current not higher than the relay's rated current.
- Check phase and neutral wiring against the diagram.
- Install the surge protective device (SPD) before the relay.
Quick selection guide
3F+N63 Aphase sequenceSuitable when you need:- to protect a three-phase supply
- to protect three-phase equipment
- to monitor each phase
Check before use:- main circuit breaker current ≤ 63 A
- whether an N conductor is present if the model needs it
Important reminder: the relay does not replace a surge protective device, circuit breakers or RCDs.FAQ
Is a neutral conductor needed?
For most three-phase voltage relays – yes, because the phase voltage is measured.Does it protect against lightning?
No – an SPD is needed for that.What current should I choose?
Not lower than the main circuit breaker current – the EL-AVR-XXTF suits up to 63 A.Does it disconnect all phases together?
Depends on the model and mode – in SYN mode all phases are disconnected together.Are settings retained?
Yes, the settings are kept during a power cut.Does it replace an RCD?
No.Three-phase voltage and current relay | 3F+N | 63 A | phase sequence | DIN | EL-AVR-XXTF
EL-AVR-XXTF – protection of a three-phase supply and three-phase equipment against voltage and phase faults.
Published: 2026-11-13 · Data verified against the supplier specification: 2026-11-13
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.This product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products







