Products catalog

Home/Product Catalog/Electrical distribution and installation/Electrical Energy Supply | Distribution Panels | Boxes | Accessories/Sealing products | seals for electrical wires | cables | panels | boxes/Cable | wire glands with nut and gasket | reliable protection against moisture | dust
  • New item   Cable gland with nut and seal | PG19 | for cable Ø12–15 mm | grey | IP68 | ES-PG19
    New item   Cable gland with nut and seal | PG19 | for cable Ø12–15 mm | grey | IP68 | ES-PG19 1
    New item   Cable gland with nut and seal | PG19 | for cable Ø12–15 mm | grey | IP68 | ES-PG19 2

    Cable gland with nut and seal | PG19 | for cable Ø12–15 mm | grey | IP68 | ES-PG19

    Code: ES-PG19
    Inquire about this item
    Price 0.27 € VAT incl.
    ( 0.22 € VAT excl. )
    Want another price? Suggest yours!

    Grey cable gland with a PG19 thread (10 mm long) and a compression nut. It seals one round cable with an outer diameter of 12–15 mm – e.g. 5×2.5–5×4 mm² power cables. Protection IP68 (EN 60529). PG19 is not a DIN 40430 size – measure the hole thread before ordering.

  • Product description

    Cable gland with nut and seal | PG19 | for cable Ø12–15 mm | grey | IP68 | ES-PG19

    ES-PG19 is a grey PG19 cable gland with a compression nut and seal. It is screwed into a PG19 threaded hole in an enclosure or panel and tightened by hand and with a spanner. When the nut is tightened, the seal grips one cable with an outer diameter of 12–15 mm and closes the gap between the cable and the enclosure.

    Key point:
    PG19 is not a DIN 40430 size, so it is the right choice when the enclosure or equipment already has a PG19 thread – when replacing an entry on an existing box or device. The Ø12–15 mm range suits cables at the upper limit of PG16 or slightly thicker, e.g. 5×2.5–5×4 mm² (a guide only – the outer diameter decides). The grey colour suits light grey panels and boxes, so the entry blends in with the enclosure.
    Thread
    PG19
    Cable Ø
    12–15 mm
    Protection
    IP68
    Thread length
    10 mm

    How it works

    Installation. With the power off, the gland is screwed into the PG19 hole and tightened by hand, then with a spanner; the cable is passed through the loosened nut.

    Operation. Turning the nut compresses the seal around the cable sheath – it fits evenly around the Ø12–15 mm cable and holds it at the same time.

    Result. A tight IP68 entry to EN 60529: dust stays out and the entry withstands continuous immersion under the conditions specified by the manufacturer.

    Why choose ES-PG19?
    It lets you replace an existing PG19 entry tightly without re-drilling or re-threading the enclosure hole – relevant when repairing equipment that already has a thread in its wall.

    Technical specifications

    Product type Cable gland with nut and seal
    Code ES-PG19
    Thread PG19 (non-DIN 40430 size)
    Thread outer diameter not specified – measure with a calliper
    Thread length 10 mm
    Cable outer diameter 12–15 mm
    Number of cables 1
    Design threaded body, compression nut, seal
    Installation screwed into the enclosure / panel, tightened by hand and with a spanner
    Degree of protection IP68 (EN 60529)
    Certificates CE, SGS, RoHS (according to supplier data)
    Colour grey
    Other colour ES-PG19B (black)

    Main functions

    • IP68 sealing – protection against dust and continuous immersion (EN 60529).
    • Cable retention – the tightened nut reduces pull on the terminals.
    • PG19 thread – a non-DIN 40430 size, so measure the hole before ordering.
    • Range Ø12–15 mm – e.g. 5×2.5–5×4 mm² power cables.
    • Thread length 10 mm – wall thickness and room for a locknut can be checked in advance.
    • Grey colour – matches light grey panels and boxes.

    Where is it used?

    • Repair of existing enclosures and boxes with a PG19 thread
    • Motor and pump terminal boxes with a PG19 hole
    • Connection of ventilation units and air handling equipment
    • Industrial socket and switch boxes
    • Outdoor boxes and cabinets where IP68 is required
    • Equipment enclosures for cables with an outer diameter of 12–15 mm

    Use by need

    For repair and service electricians.
    When an old PG19 entry has cracked, the new gland screws into the same hole – no new drilling or tapping needed.
    For equipment manufacturers.
    If the enclosure drawing specifies a PG19 hole, this size keeps the existing design and achieves IP68.
    For facility managers.
    Replacing only the worn entry makes the equipment tight again without changing the enclosure.

    Practical application

    If an old PG19 entry has cracked on a ventilation unit terminal box and the supply cable has an outer diameter of about 14 mm, first measure the hole thread with a calliper and compare it with the ES-PG19 thread; if they match, screw in the new gland, pass the cable through, tighten the nut by hand and with a spanner, and the box is sealed again.

    Pros

    • IP68 to EN 60529
    • Clear range Ø12–15 mm for one PG19 size
    • Thread length specified – 10 mm
    • Tightened by hand and with a standard spanner
    • CE, SGS, RoHS according to supplier data
    • Also available in the other colour – ES-PG19B (black)

    Cons / limitations

    • Limited range: for a cable thinner than Ø12 mm choose ES-PG16 (PG16, Ø10–14 mm), for one thicker than Ø15 mm – ES-PG21 (PG21, Ø13–18 mm).
    • One gland – one round cable; not suitable for a flat cable or several wires.
    • Material and operating temperature are not given in our data – check before buying for hot or chemically aggressive environments.
    • PG19 is not a DIN 40430 size – the thread outer diameter is not given in our data, so the hole and thread must be measured with a calliper before ordering.
    • Not a fire barrier – it does not replace fire-rated cable penetrations through fire walls.

    Safety and installation notes

    • Work in a panel or box only with the power disconnected and absence of voltage verified.
    • After drilling, remove all swarf from the enclosure – it can cause a short circuit.
    • PG19 is not a DIN 40430 size – before drilling or ordering, measure the thread with a calliper and compare it with the mating part.
    • Tighten first by hand, then with a spanner until the cable no longer moves in the seal; do not overtighten the thread.
    • Route the cable from below or with a drip loop so that water does not run along the cable to the gland.

    Quick selection guide

    PG19 thread (measure)
    Cable Ø12–15 mm
    IP68, thread length 10 mm
    Grey, ES-PG19
    Suitable when you need:
    • a tight entry for one cable with an outer diameter of 12–15 mm
    • an IP68 entry outdoors, in basements or damp rooms
    • an entry that matches a light grey panel or box
    Check before use:
    • The cable outer diameter with a calliper – it must be 12–15 mm.
    • The hole thread with a calliper – PG19 is not a DIN 40430 size, so compare the dimensions with the gland.
    • The environment – material, operating temperature and UV resistance are not given in our data.
    Important reminder: The gland seals and holds one cable, but it is not a fire barrier: cable penetrations through fire walls need separate fire-stopping solutions.

    FAQ

    What cable size does ES-PG19 fit?
    A cable with an outer diameter of 12–15 mm – measure the sheath, not the conductor cross-section in mm².
    Is ES-PG19 suitable for a 5×4 mm² cable?
    Often yes – the outer diameter of such a cable usually falls within 12–15 mm, but it depends on the cable type and manufacturer, so measure it before buying.
    What hole size does a PG19 gland need?
    PG19 is not a DIN 40430 size, so we do not state a hole diameter – measure the gland and hole threads with a calliper; a PG16 or PG21 gland will not fit a PG19 hole.
    How does ES-PG19 differ from ES-PG19B?
    Only in colour: ES-PG19 is grey, ES-PG19B is black; thread, range and IP68 are the same.
    Is ES-PG19 suitable for continuous use under water?
    IP68 to EN 60529 covers continuous immersion, but the exact depth and duration are set by the manufacturer – they are not given in our supplier's data.
    What material is the gland made of and what is its operating temperature?
    The supplier has not specified these, so we do not guarantee them – for heat or chemicals, consult us before buying.

    ES-PG19 – PG19 cable gland Ø12–15 mm, grey, IP68

    Grey PG19 cable gland with nut and seal ES-PG19 for one cable Ø12–15 mm (e.g. 5×2.5–5×4 mm² power cables). IP68, thread length 10 mm, CE, SGS, RoHS according to supplier data.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.

  • Alternative products

    CYKY 5x4 | Copper power cable | CYKY-L 5G4 | 1m | black  
    CYKY 5x4 | Copper power cable | CYKY-L 5G4 | 1m | black
    Code: 91950413
    Price 3.68 € VAT incl.
    ( 3.04 € VAT excl. )
    Add to cart 

  • Subscribtion to new arrivals

    privacy policy

    Information