Products catalog

  • Insulated twin bootlace ferrule | 2×1mm² | 8mm | crimp | red | 100 pcs | Phoenix Contact AI-TWIN 2X 1-8 RD | 3200810

    Code: 3200810
    Barcode: 4017918094362

    Insulated twin wire end ferrule 2 × 1 mm² for flexible wires, 8 mm tube, red. Phoenix Contact AI-TWIN 2X 1-8 RD, tin-plated copper, PP collar. 100 pcs per pack.

  • Insulated twin bootlace ferrule | 2×1mm² | 8mm | crimp | red | 100 pcs | Phoenix Contact AI-TWIN 2X 1-8 RD | 3200810

    The insulated twin ferrule terminates two flexible 1 mm² wires in one terminal. Both wires are crimped in one tin-plated copper tube, so a single solid pin enters the terminal of a circuit breaker, relay or terminal block.

    Key point:
    Without a ferrule, two flexible wires in one terminal are rarely clamped evenly – over time one of them loosens and heats up. A twin ferrule joins both wires into one pin, so the bridge between devices stays reliable.
    Cross-section
    2 × 1 mm²
    Tube length
    8 mm
    Colour
    red
    Pack
    100 pcs

    Operating principle

    Strip the insulation to the ferrule tube length (8 mm), twist the strands and insert both wires fully – the wire insulation must enter the insulating collar.

    The ferrule is crimped with ferrule crimping pliers using a square or trapezoidal profile. The tube and strands are compressed into one solid pin.

    The crimped pin is inserted into the terminal and tightened to the equipment manufacturer's torque – the terminal clamps solid metal, not individual strands.

    Why choose Phoenix Contact AI-TWIN 2X 1-8 RD?
    Tin-plated copper tube and PP collar, dimensions to DIN 46228-4, UL 486F; the red colour (DIN 46228-4) identifies the cross-section at a glance, without measuring.

    Technical specifications

    Product typeInsulated twin bootlace ferrule (wire end ferrule)
    ManufacturerPhoenix Contact (Germany)
    ModelAI-TWIN 2X 1-8 RD
    Manufacturer code3200810
    EAN4017918094362
    Wire cross-section2 × 1 mm²
    Tube (pin) length8 mm
    Overall length15 mm
    Tube inner Ø2.05 mm
    Collar Ø3.4 mm
    Collar colourred (colour code DIN 46228-4)
    Materialelectrolytic copper, tin-plated; insulating collar – polypropylene (PP)
    StandardDIN 46228-4, UL 486F
    Operating temperatureup to 105 °C (short-term 120 °C)
    Pack100 pcs
    CertificatecULus (E488001)

    Key functions

    • Strand compression – the terminal clamps the full cross-section, not individual strands.
    • Tin-plated copper – lower contact resistance and protection against oxidation.
    • Insulating collar – protects the wire entry and eases insertion.
    • Colour code – the cross-section is recognised at once during installation and panel inspection.
    • Two wires in one pin – bridges between devices without extra terminals.

    Where is it used?

    • Residential distribution boards
    • Automation and control panels
    • Screw and spring terminal blocks
    • Circuit breakers, RCDs, contactors
    • Controllers, relays, power supplies
    • Motor and equipment connection boxes

    Use by need

    Automation panel installer.
    Bridges between devices without extra terminals or busbars.
    Panel builder.
    Uniform, verifiable connections in series production.
    Maintenance technician.
    Fewer loose connections in vibrating equipment.

    Practical use

    If you need to bridge the supply of several circuit breakers, crimp two 1 mm² wires in one twin ferrule – each terminal then receives one pin and both wires are clamped evenly.

    Advantages

    • Strands do not splay or break in the terminal
    • Stable contact even under vibration
    • Tin-plated copper – protection against oxidation
    • Colour coding by cross-section
    • Pack of 100 pcs

    Disadvantages / limitations

    • For flexible wires only – not needed for solid wire
    • Requires ferrule crimping pliers – ordinary pliers do not crimp properly
    • Single use – after removal the wire end must be cut off
    • Tube length 8 mm – for a terminal of different depth choose another length

    Safety and installation notes

    • Switch off the voltage and verify it is absent before work.
    • Choose the ferrule exactly to the wire cross-section (2 × 1 mm²) – not larger, not smaller.
    • Crimp only with the intended tool and the correct die.
    • Do not use a badly crimped ferrule – cut it off and crimp a new one.
    • Tighten the terminal to the manufacturer's torque and check the wire with a pull test.

    Quick selection guide

    2 × 1 mm²
    8 mm
    red
    100 pcs
    Phoenix Contact AI-TWIN 2X 1-8 RD
    Suitable when you need:
    • two flexible wires in one terminal
    • a neat, easily inspected connection
    • reliable contact in vibrating equipment
    Check before use:
    • the wire cross-section (2 × 1 mm²)
    • the terminal depth and tube length (8 mm)
    • that you have ferrule crimping pliers
    Important reminder: A ferrule does not replace correct sizing of the wire and the protective device – it ensures a quality wire-end connection.

    FAQ

    Is a ferrule needed for solid wire?
    No – it is intended for flexible (stranded) wires.
    Which wire does this ferrule fit?
    A flexible 2 × 1 mm² wire.
    What do I crimp it with?
    Ferrule crimping pliers with a square or trapezoidal profile.
    How much insulation should be stripped?
    As long as the tube – 8 mm.
    What does the colour mean?
    The colour indicates the cross-section according to the DIN 46228-4 colour code.
    Can wires of different sizes be combined?
    No – both wires must be 1 mm².

    Insulated twin bootlace ferrule | 2×1mm² | 8mm | crimp | red | 100 pcs | Phoenix Contact AI-TWIN 2X 1-8 RD | 3200810

    Insulated twin bootlace ferrule 2 × 1 mm², 8 mm tube, red, 100 pcs – Phoenix Contact AI-TWIN 2X 1-8 RD. Reliable termination of flexible wires for panels, automation and equipment.

    Published: 2026-11-12 · Data verified against the manufacturer datasheet: 2026-11-12

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Terminal block | electrical wire connector | universal | 3x0.2-4mm² | for all types of wires | WAGO | 221-413 | 4050821808442
    Code: WAGO 221-413

    Universal 3-wire terminal block, designed for fast, safe and neat connection of electrical wires. This connector is suitable for solid, stranded and flexible wires, therefore it is widely used both in household electrical installations and in professional installation work.

    The convenient lever system allows the wire to be connected very quickly: lift the lever, insert the conductor and lock it by lowering the lever. The connector has a transparent housing, making it easier to visually check whether the wire has been inserted correctly. 

    Price 0.33 € VAT incl.
    ( 0.27 € VAT excl. )
  • Subscribtion to new arrivals

    privacy policy

    Information