Interposing relay | 12 V DC coil | 1CO (SPDT) | 8 A | with test button | plug-in | LANBOO J13A | ES-J13A1
Code: ES-J13A1Price 4.10 € VAT incl.( 3.39 € VAT excl. )LANBOO J13A plug-in interposing relay: 12 V DC coil, 1CO (NO + NC) 8 A, manual test button. Mounts in a socket.
-
Interposing relay | 12 V DC coil | 1CO (SPDT) | 8 A | with test button | plug-in | LANBOO J13A | ES-J13A1
LANBOO J13A is a plug-in electromechanical interposing relay for control circuits: 12 V DC coil and one changeover contact (NO + NC with a common terminal) rated up to 8 A. The relay plugs into a matching socket, so it can be replaced quickly without disconnecting any wires.
Key point:
A plug-in relay is a practical choice for panels where fast servicing matters: a faulty relay is replaced in seconds. The 8 A contact suits most control circuits – contactor coils, signal lamps and small loads.Coil
12 V DCContact
1CO (SPDT) – NO + NCContact current
8 ATest button
yes, manualOperating principle
The relay plugs into a socket mounted on a DIN rail or panel. The control signal connects to the coil terminals, and the load circuit to the common (COM), NO and NC terminals.
When 12 V DC is applied to the coil, the contact changes over: COM connects to NO and disconnects from NC. When the signal is removed, the contact returns to its initial position.
A manual test button lets you operate the contact mechanically without a control signal – convenient for checking the circuit during commissioning.
Result: the controller is loaded only by the coil current, while the load is switched by an isolated contact.
Why choose the LANBOO J13A?
The plug-in design shortens repair time, silver alloy contacts suit control circuits, and the test button lets you check the load circuit before the controller program is running.Technical specifications
Product type Plug-in electromechanical interposing relay Manufacturer / code LANBOO / ES-J13A1 Series J13A Coil voltage 12 V DC Contact configuration 1CO (SPDT): 1 NO + 1 NC with common terminal Contact current 8 A Contact material silver alloy Manual test button yes Housing sealed, transparent plastic Mounting in socket (socket sold separately) Key functions
- Signal isolation – protects the controller from the load circuit.
- NO/NC changeover contact – switching on or off with a single relay.
- Plug-in design – fast replacement without disconnecting wires.
- Test button – manual contact operation during commissioning.
- Sealed housing – protects the mechanism from dust.
Where is it used?
- Control cabinets and automation panels
- PLC output expansion
- Driving coils of contactors and magnetic starters
- Signalling and alarm circuits
- Pump, fan and heating control
- Gate, barrier and lighting automation
Use by need
For control cabinet manufacturers.
Plug-in relays allow the panel to be assembled and tested first, with relays inserted at the final stage.For maintenance teams.
A faulty relay is replaced in seconds without disconnecting wires.For commissioning engineers.
The test button lets you check the actuator without the controller program.Practical application
If a controller 12 V DC output has to drive a contactor coil, connect the output to the J13A coil and route the contactor coil through the COM–NO contact. Before starting the program, press the test button to check that the contactor pulls in.Pros
- Plug-in – fast replacement
- 1 changeover contact NO + NC
- 8 A contact current
- Silver alloy contacts
- Sealed housing
- Manual test button
Cons / limitations
- Requires a matching J13A socket – not included
- Contact current up to 8 A – larger loads require a contactor
- Inductive loads require a current margin
Safety and installation notes
- Disconnect the load circuit voltage before installing or replacing the relay.
- The coil voltage must match the control signal: 12 V DC.
- Use only the socket designed for this relay – an unsuitable socket may not ensure proper contact.
- Do not use the test button as an operating switch – it is intended for testing only.
- Installation must be carried out by a qualified electrician.
Quick selection guide
Coil: 12 V DC1CO (SPDT)8 APlug-inWith test buttonSuitable when you need to:- drive a contactor coil or signal lamp from a controller
- have quickly replaceable relays in the panel
- test the circuit manually
Check before use:- control signal voltage – 12 V DC
- whether you have a J13A series socket
- load current and type
Important reminder: A relay is not a protective device – it does not protect against overload or short circuit.FAQ
Is the socket included?
No, the relay is sold without a socket – ask our sales managers about a matching socket.What does 1NO + 1NC mean?
It is one changeover contact with a common terminal: normally open and normally closed outputs.What current can the contact switch?
Up to 8 A.What is the test button for?
It lets you operate the contact manually when commissioning or testing the circuit.Is it suitable for a PLC output?
Yes, if the PLC output voltage is 12 V DC.Does the relay protect against overload?
No, the circuit must be protected by a circuit breaker or fuse.Interposing relay | 12 V DC coil | 1CO (SPDT) | 8 A | with test button | plug-in | LANBOO J13A | ES-J13A1
LANBOO J13A plug-in interposing relay: 12 V DC coil, 1CO 8 A contact with silver alloy contacts, manual test button – for control circuits, PLCs and automation panels.
Published: 2026-11-05 · Data verified against the supplier's specification and product marking: 2026-11-05
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.This product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products
Modular photo relay | twilight switch with external sensor | 16 A | 12–240 V AC/DC | 1–50,000 lx | 1CO | DIN | GanzKK | SOU-1/UNICode: SOU-1/UNIDIN rail twilight switch with universal 12–240 V AC/DC supply and external sensor: 1–50,000 lx, 1CO 16 A AC1, 0–2 min delay, 1 module.
Price 42.47 € VAT incl.( 35.10 € VAT excl. )














