Products catalog

  • Three-phase voltage indicator | 3F | 80–500 V AC | LCD | DIN | VEXEN | DVI3P

    Code: DVI3P

    The VEXEN DVI3P is a three-phase digital voltage indicator for DIN-rail mounting: it shows the voltage of each phase but does not disconnect the load.

  • Three-phase voltage indicator | 3F | 80–500 V AC | LCD | DIN | VEXEN | DVI3P

    The VEXEN DVI3P is a three-phase digital voltage indicator for DIN-rail mounting: it shows the voltage of each phase but does not disconnect the load. It is the simplest way to see what is happening in the network when you open the board.

    Key point:
    Phase voltages drifting apart is a common sign of a deteriorating neutral connection. The indicator lets you notice it before the neutral breaks completely.
    Voltage limits
    80–500 V AC, 50–60 Hz
    Network / supply
    3F, 80–500 V AC
    Functions
    voltage display only

    How it works

    The indicator is connected to phases L1, L2, L3 and neutral, measures the voltage of each phase and shows it on the display.

    The voltage is updated continuously, so you immediately see in which phase it is too high or too low.

    The indicator does not disconnect anything – a voltage relay is needed for protection.

    Why choose the VEXEN DVI3P?
    You see the voltage of all phases without a multimeter – network problems are noticed sooner.

    Technical specifications

    Product type Three-phase digital voltage indicator (does not disconnect)
    Manufacturer / code VEXEN / DVI3P
    Measured voltage 80–500 V AC, 50–60 Hz
    Measuring accuracy ±2 %
    Insulation voltage Ui 660 V
    Sampling rate 1 / s
    Own consumption ≤ 2 VA
    Operating temperature −20…+55 °C
    Display / indication LCD
    Degree of protection IP20
    Mounting DIN 35 mm

    Main functions

    • Three-phase voltage display – separately for each phase.
    • Digital display or indication – the status is visible at once.

    Where is it used?

    • Distribution boards (residential and industrial)
    • Control cabinets
    • Generator and solar plant panels
    • Temporary construction site boards

    Use by need

    For the home owner.
    You see whether the mains voltage is normal.
    For the electrician.
    Quick diagnostics without a multimeter.
    For the facility administrator.
    Network status at a glance.

    Practical use

    Opening the board you see 248 V – 231 V – 209 V: the phases drift apart, so it is worth checking the neutral connections before the neutral breaks.

    Pros

    • Shows the voltage of all phases
    • Compact
    • Simple installation

    Cons / limitations

    • Does not disconnect the load – it is not a protection device
    • Does not measure current

    Safety and installation notes

    • Install only after disconnecting the supply.
    • Protect the measuring wires with fuses or a circuit breaker.
    • Work must be done by a qualified electrician.

    Quick selection guide

    3F
    80–500 V AC
    LCD
    Suitable when you need:
    • to see the voltage of all phases in the board
    Check before use:
    • network voltage 80–500 V AC
    Important reminder: the indicator only shows the voltage – a voltage relay is needed for protection.

    FAQ

    Does the indicator disconnect the load?
    No – it only shows the voltage.
    Is a neutral needed?
    Yes, the phase voltage is measured relative to neutral.
    What is the accuracy?
    ±2 %.
    How much space does it take?
    See the technical table.
    Does it show current?
    No.
    What if the voltages differ?
    Check the neutral connections and the load distribution among the phases.

    Three-phase voltage indicator | 3F | 80–500 V AC | LCD | DIN | VEXEN | DVI3P

    VEXEN DVI3P – the voltage of all three phases in the board at a glance.

    Published: 2026-11-13 · Data verified against the manufacturer's datasheet: 2026-11-13

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Non-perforated DIN rail | profile | for mounting modular equipment in a distribution board | 35x7mm | 1m | BAKS | EURO | SZB35H 7/1 | 0613310
    Code: 0613310

    BAKS EURO SZB35H 7/1 – a non-perforated steel DIN rail designed for mounting modular electrical and automation equipment in distribution boards and control cabinets. Profile dimensions – 35 × 7 mm, steel thickness – 1.0 mm, length – 1000 mm (1 m). The solid non-perforated base allows mounting points to be selected according to the specific construction; the price is indicated per 1 metre. 

    Price 0.88 € VAT incl.
    ( 0.73 € VAT excl. )
    Electrical distribution | modular enclosure | box | distribution board | 36 modules (2x18) | 432x448x161mm | transparent door | waterproof | surface-mounted | plastic | IP65 | Legrand | PLEXO | 601986 | 3245066019864
    Code: 601986

    Hermetic electrical distribution enclosure designed for the safe installation of modular electrical devices in both indoor environments and more demanding outdoor or industrial conditions. This is a high-quality IP65 protection class electrical box adapted to protect automation, protection, and electrical distribution equipment from dust, moisture, water splashes, and mechanical impact. 

    Price 87.95 € VAT incl.
    ( 72.69 € VAT excl. )
  • Subscribtion to new arrivals

    privacy policy

    Information