Products catalog

  • Interposing relay with socket | 24 V DC coil | 1CO (SPDT) | 6 A | LED | ultra-slim | DIN | LANBOO | ES-LBJ6A24

    Code: ES-LBJ6A24

    Ultra-slim interposing relay module with socket for DIN rail: 24 V DC coil, 1CO 6 A 250 V AC, LED indication.

  • Interposing relay with socket | 24 V DC coil | 1CO (SPDT) | 6 A | LED | ultra-slim | DIN | LANBOO | ES-LBJ6A24

    LANBOO LBJ6A is a pre-assembled interposing relay module: the relay is already fitted into a slim socket with screw terminals and mounts directly on a 35 mm DIN rail. The coil is driven by a 24 V DC signal, and one changeover contact (NO + NC with a common terminal) switches loads up to 6 A 250 V AC.

    Key point:
    When a controller or PLC output has to switch a 230 V circuit, an interposing relay separates the low-current control side from the load. A module with an integrated socket and LED saves panel space and installation time – no need to assemble the relay and socket separately.
    Coil
    24 V DC
    Contact
    1CO (SPDT) – NO + NC
    Contact rating
    6 A / 250 V AC
    Mounting
    DIN rail, with socket

    Operating principle

    The module snaps onto a 35 mm DIN rail; the control wires connect to coil terminals A1/A2, and the load circuit to the common (COM), normally open (NO) and normally closed (NC) terminals.

    When 24 V DC is applied to the coil, the electromagnet switches the contact: COM disconnects from NC and connects to NO, and the LED indicator lights up. When the control signal is removed, a spring returns the contact to its initial position.

    Result: the controller or sensor is loaded only by the coil current, while the load is switched by a galvanically isolated contact.

    Why choose the LANBOO LBJ6A?
    One product replaces both relay and socket, the LED instantly shows whether the PLC signal has arrived, and the slim housing lets you fit many channels in a single DIN row.

    Technical specifications

    Product type Electromechanical interposing relay with socket (relay module)
    Manufacturer / code LANBOO / ES-LBJ6A24
    Series LBJ6A
    Coil voltage 24 V DC
    Contact configuration 1CO (SPDT): 1 NO + 1 NC with common terminal
    Contact rating 6 A / 250 V AC (resistive load)
    Contact resistance ≤ 50 mΩ
    Indication LED, coil status
    Design ultra-slim relay module, relay fitted in socket
    Mounting 35 mm DIN rail
    Connection screw terminals

    Key functions

    • Signal isolation – protects the PLC or controller output from the load circuit.
    • NO/NC changeover contact – the same relay can switch a circuit on or off.
    • LED indication – quick diagnostics without a measuring instrument.
    • Integrated socket – mounts straight onto the DIN rail.
    • Ultra-slim housing – many channels in a small panel.

    Where is it used?

    • Expanding discrete outputs of PLCs and logic controllers
    • Lighting group control from automation systems
    • Fan, pump and damper control circuits
    • Control of signal lamps and sirens
    • Driving contactor coils from a low-current signal
    • HVAC and building automation panels
    • Smart home controllers with 24 V DC outputs

    Use by need

    For automation integrators.
    Fast channel expansion in the panel without sourcing sockets and relays separately.
    For panel builders.
    Uniform slim modules line up neatly on the DIN rail and are easy to label.
    For service electricians.
    The LED lets you check on site whether the controller is sending a signal.

    Practical application

    If a PLC 24 V DC transistor output has to switch a 230 V fan of up to 6 A, connect the output to the relay coil and route the fan's phase through the COM–NO contact. The lit LED confirms the command, and the PLC output is loaded only by the coil current.

    Pros

    • Relay and socket in one product
    • Ultra-slim housing saves space
    • LED status indication
    • NO + NC changeover contact
    • Direct DIN rail mounting

    Cons / limitations

    • Contact rating up to 6 A – larger loads require a contactor
    • Inductive loads (motors, coils) require a current margin
    • Only one changeover contact – for two circuits choose a 2CO relay

    Safety and installation notes

    • Before installation, disconnect the power and verify that no voltage is present.
    • The coil voltage must exactly match the control signal: 24 V DC. A different voltage may damage the relay.
    • The load current must not exceed 6 A; leave a margin for inductive loads.
    • Route coil and load circuit wiring separately; do not mix SELV and 230 V circuits in one terminal.
    • Installation and connection must be carried out by a qualified electrician.

    Quick selection guide

    Coil: 24 V DC
    1CO (SPDT)
    6 A / 250 V AC
    DIN, with socket
    LED
    Suitable when you need to:
    • isolate a PLC or controller output from a 230 V load
    • switch a signal from NO to NC
    • fit many channels into a narrow panel
    Check before use:
    • control signal voltage – 24 V DC
    • load current and type (resistive / inductive)
    • whether one or two changeover contacts are needed
    Important reminder: A relay is not a protective device – it does not protect against overload or short circuit; the circuit must be protected by a circuit breaker or fuse.

    FAQ

    Is a separate socket required?
    No, the relay is already fitted into the socket and mounts directly on the DIN rail.
    What does 1CO (SPDT) mean?
    It is one changeover contact with a common terminal and two outputs – normally open (NO) and normally closed (NC).
    Can it switch a 230 V load?
    Yes, provided the load current does not exceed 6 A 250 V AC.
    Is it suitable for a PLC transistor output?
    Yes, if the PLC output voltage is 24 V DC.
    What is the LED for?
    The LED shows that the coil is energised – this speeds up troubleshooting.
    Does it protect against short circuit?
    No, protection requires a circuit breaker or fuse.

    Interposing relay with socket | 24 V DC coil | 1CO (SPDT) | 6 A | LED | ultra-slim | DIN | LANBOO | ES-LBJ6A24

    Ultra-slim LANBOO LBJ6A relay module with socket for DIN rail: 24 V DC coil, 1CO 6 A 250 V AC contact and LED indication – for PLC output isolation and load control in automation panels.

    Published: 2026-11-05 · Data verified against the supplier's specification and product marking: 2026-11-05

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Modular photo relay | twilight switch with external sensor | 16 A | 12–240 V AC/DC | 1–50,000 lx | 1CO | DIN | GanzKK | SOU-1/UNI
    Code: SOU-1/UNI

    DIN rail twilight switch with universal 12–240 V AC/DC supply and external sensor: 1–50,000 lx, 1CO 16 A AC1, 0–2 min delay, 1 module.

    Price 42.47 € VAT incl.
    ( 35.10 € VAT excl. )
  • Subscribtion to new arrivals

    privacy policy

    Information