Products catalog

Home/Product Catalog/Automation and Control Systems/Control components for automation and control systems/Buttons for automation control | control systems
  • New item   Push button with LED illumination | 22 mm | 1NC | red | metal | LED 230 V | IP40 | non-latching | Promfactor Baltic | FP PCPI r 1NC

    Push button with LED illumination | 22 mm | 1NC | red | metal | LED 230 V | IP40 | non-latching | Promfactor Baltic | FP PCPI r 1NC

    Code: FP PCPI r 1NC
    Barcode: 4779040157208
    Inquire about this item
    Price 6.32 € VAT incl.
    ( 5.22 € VAT excl. )

    Push button with LED illumination Ø 22 mm, 1NC, red, LED 230 V, IP40, Promfactor Baltic FP PCPI r 1NC. For control circuits: AC-15 6 A / DC-13 0.6 A, Ui 660 V.

  • Product description

    Push button with LED illumination | 22 mm | 1NC | red | metal | LED 230 V | IP40 | non-latching | Promfactor Baltic | FP PCPI r 1NC

    FP PCPI r 1NC is a red illuminated metal push button switch from the Promfactor Baltic FP series, with 1NC contact and 230 V LED illumination. It is mounted in a Ø 22 mm hole in a panel door, control desk or push button enclosure; front protection degree IP40.

    Key idea:
    According to EN 60204-1, red is intended for stopping (STOP / OFF). Red must not be used for starting, and near an emergency stop the standard recommends a black STOP button. The NC contact opens the circuit when pressed, and if a wire breaks the device also stops – this is the safe STOP principle.
    Contact
    1NC
    Button type
    illuminated, non-latching
    Mounting
    Ø 22 mm hole
    Illumination
    LED 230 V
    Degree of protection
    IP40 front
    Colour
    red

    How it works

    The button is inserted into a Ø 22 mm hole and tightened from the rear with a nut. The contact block is connected with screw terminals, tightening torque 0.8 Nm.

    At rest the NC contact is closed; when pressed it opens the circuit and returns when released. A STOP button is connected in series with the contactor coil, so pressing it or a broken wire stops the equipment.

    The LED illumination is powered at 230 V, so the control circuit must have the same voltage. A different voltage will burn out the LED or it will not light.

    Why choose FP PCPI r 1NC? Button and indicator in one – the operator sees the status and fewer holes are needed in the door.

    Technical specifications

    Product type Push button with LED illumination, non-latching
    Manufacturer / code Promfactor Baltic / FP PCPI r 1NC
    EAN 4779040157208
    Series FP (22 mm control push buttons)
    Housing metal
    Colour red
    Contact 1NC
    Illumination LED 230 V
    Standard IEC/EN 60947-5
    Utilization category AC-15 / DC-13
    Rated voltage Ue up to 380 V AC / 220 V DC
    Rated current 6 A (AC) / 0.6 A (DC)
    Insulation voltage Ui 660 V
    Frequency 50/60 Hz
    Mechanical life 1,000,000 cycles
    Degree of protection IP40 on the operating side
    Mounting hole Ø 22 mm
    Terminal tightening torque 0.8 Nm
    Operating temperature -25…+45 °C
    Storage temperature -25…+55 °C
    Warranty 24 months from start of use (max. 30 months from sale)

    Main functions

    • 1NC contact – opens the control circuit when pressed
    • Spring return – returns to the initial position when released
    • LED indication – shows the status, 230 V
    • Ø 22 mm mounting – fits standard panel holes and push button enclosures
    • Screw terminals – reliable wire connection, 0.8 Nm

    Where is it used?

    • Control panels for pumps, fans and compressors
    • Motor START–STOP control with a contactor
    • Commands in automation panels and PLC inputs
    • Push button enclosures at machines and control desks

    Use by need

    For the installing electrician. A standard 22 mm hole, screw terminals and clear contact marking allow quick installation and replacement of an old button.
    For automation panel builders. Buttons, lamps and START–STOP units from one series allow a panel with a uniform look.
    For equipment maintenance. A frequently replaced component worth keeping in stock by colour and contact.

    Practical use

    In a ventilation panel with a 230 V control circuit, the illuminated button both controls the unit and shows its status, so no separate indicator lamp is needed.
    Pros
    • Button and indicator in one
    • Status visible from a distance
    • Standard Ø 22 mm hole
    • Ui 660 V, AC-15 / DC-13
    Cons
    • IP40 – not suitable outdoors or in washdown areas without an extra cover
    • The LED voltage must exactly match the control voltage
    • Not intended for switching motor current directly

    Safety and installation notes

    • Installation and connection must be performed by a qualified electrician after disconnecting the voltage and verifying that there is none.
    • Protect the control circuit with a separate circuit breaker or fuse according to the wire cross-section.
    • Use an NC contact for the STOP function and a spring-return NO with contactor self-holding for START.
    • Metal doors with equipment must be connected to PE.
    Quick selection guide
    Ø 22 mm1NCredLED 230 VIP40non-latchingAC-15 / DC-13

    FAQ

    ⚡ Does FP PCPI r 1NC have illumination?
    Yes, 230 V LED illumination. It is connected to a control circuit of the same voltage.
    ⚡ What contact does it have?
    One 1NC contact: the circuit opens when pressed.
    ⚡ What hole size is needed?
    A standard Ø 22 mm hole in a panel door, control desk or push button enclosure.
    ⚡ Does the button latch?
    No, the button is spring return – it returns to its initial position when released.
    ⚡ What current can it switch?
    According to the manufacturer, the rated current is 6 A (AC-15) and 0.6 A (DC-13). The button is intended for control circuits; the motor is connected via a contactor.

    Push button with LED illumination | 22 mm | 1NC | red | metal | LED 230 V | IP40 | non-latching | Promfactor Baltic | FP PCPI r 1NC

    FP PCPI r 1NC is a reliable Promfactor Baltic FP series 1NC push button for a Ø 22 mm hole with 230 V LED. Suitable for panels, control desks and push button enclosures in dry rooms. Need help selecting buttons for a whole panel? Send us the diagram – we will select the components and send a quote.

    Published: 2026-11-05 · Data verified against the manufacturer datasheet: 2026-11-05

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.

  • Alternative products

    Crane control panel | with 4 buttons | 5A | 120–400V | IP54 Top seller  
    Crane control panel | with 4 buttons | 5A | 120–400V | IP54
    Code: BPU10-4

    Button control panels are designed for switching electrical control circuits of lifting mechanisms. The sealed IP54 enclosure is made of heat-resistant ABS plastic with built-in buttons. A protective gland is provided to seal the cable entry, and a sealing gasket is installed between the enclosure and the panel.

    The buttons meet the "CE" standard requirements in terms of design and technical specifications.

    The remote control panels have passed certification tests and have received serial production conformity certificates.
    Available with 2, 4, or 6 buttons.
    The housing is made of non-flammable ABS plastic.
    The cable entry includes a protective gland that prevents moisture and dust from entering the housing. 

    Price 20.57 € VAT incl.
    ( 17.00 € VAT excl. )
    Add to cart 
  • privacy policy

    Information