Products catalog

  • Temporary construction site distribution board | 3×CEE 16 A 5P + 1×CEE 32 A 5P + 4×Schuko 230 V | 4P residual current device | 50 A | IP44 | 257×409×160 mm | IEK | 0020324

    Code: 0020324

    A ready-to-use temporary construction site distribution board fitted with three 3-phase CEE 16 A sockets, one 3-phase CEE 32 A socket and four Schuko 230 V sockets. The main device is a 4-pole residual current device, TN-S system, IP44 protection.

  • Temporary construction site distribution board | 3×CEE 16 A 5P + 1×CEE 32 A 5P + 4×Schuko 230 V | 4P residual current device | 50 A | IP44 | 257×409×160 mm | IEK | 0020324

    A ready-to-use temporary construction site distribution board fitted with three 3-phase CEE 16 A sockets, one 3-phase CEE 32 A socket and four Schuko 230 V sockets. The main device is a 4-pole residual current device, TN-S system, IP44 protection.

    Key idea:
    One board replaces several extension leads and improvised connections: powerful 3-phase tools, a concrete mixer or a welder plug into the CEE sockets, hand tools and lighting into the Schuko sockets. The residual current device reduces the risk of electric shock in the damp site environment.
    Sockets
    3×CEE 16 A + 1×CEE 32 A + 4×Schuko
    Rated current
    50 A
    Protection
    4P RCD
    Degree of protection
    IP44

    How it works

    The board is supplied from a 3-phase 230/400 V network (TN-S system, 5 wires) from a temporary supply, a generator or the building switchboard. The supply cable enters the enclosure and is connected to the incoming device.

    The main device is a 4-pole residual current device: it disconnects all sockets if an earth leakage is detected (e.g. damaged tool insulation or a cable lying in water). Downstream of the RCD the power is distributed to the 3-phase CEE and single-phase Schuko sockets.

    The result is one sealed IP44 distribution point with clearly separated 400 V and 230 V sockets that can be moved around the site as the work front changes.

    Why choose IEK 0020324?
    A factory-assembled board saves assembly time: there is no need to buy an enclosure, sockets and RCD separately and wire them on site. The socket combination covers the typical site demand – 3-phase machinery and hand tools.

    Technical specifications

    Product typeTemporary construction site supply / distribution board with sockets
    Manufacturer / codeIEK / 0020324
    Rated voltage230/400 V
    Rated frequency50 Hz
    Rated current50 A
    System configurationTN-S
    Main deviceResidual current device, 4P
    3-phase sockets3× CEE 16 A 400 V 5P; 1× CEE 32 A 400 V 5P
    Single-phase sockets4× Schuko 230 V with earthing contact
    Short-circuit withstand4.5 kA
    Rated impulse withstand voltage2.5 kV
    Degree of protectionIP44
    Climatic versionU1 (outdoor conditions)
    Dimensions (H×W×D)257 × 409 × 160 mm

    Main functions

    • 3-phase CEE 16 A and 32 A sockets – connect powerful tools, mixers and compressors without adapters.
    • Four Schuko sockets – hand tools, chargers and lighting at the same time.
    • 4P residual current device – disconnects all sockets in the event of earth leakage.
    • IP44 enclosure – protects against water splashes and solid particles on site.
    • TN-S configuration – separate N and PE conductors in line with modern temporary supply requirements.
    • Compact dimensions – easy to move and fix to a post or wall.

    Where is it used?

    • Private house construction sites
    • Renovation and finishing works
    • Roofing, facade and foundation works
    • Temporary power on road and utility network sites
    • Farms and seasonal outdoor work
    • Temporary workshops and storage areas

    Use by need

    For the construction contractor.
    One board for the whole work front – 3-phase machinery and hand tools.
    For the electrician setting up temporary supply.
    A ready unit with an RCD shortens installation time on site.
    For the self-builder.
    A safe and tidy power point on site instead of a tangle of extension leads.

    Practical application

    If a concrete mixer (CEE 16 A), a welder (CEE 32 A) and several hand tools work on site at the same time, this board lets you connect them in one place, and the RCD will cut the power if any tool cable is damaged.

    Pros

    • Factory-assembled – sockets and RCD already installed
    • Wide socket mix: 400 V 16 A and 32 A plus 230 V
    • 4-pole RCD protects all groups
    • IP44 enclosure for outdoor conditions
    • TN-S system, 4.5 kA short-circuit withstand

    Cons / limitations

    • The supplier specification lists no separate circuit breakers for socket groups – overload and short-circuit protection must be provided on the supply side
    • IP44 – not suitable for immersion or standing in water
    • Total load is limited by the 50 A rated current
    • No energy metering – if a meter is required, choose a metering board

    Safety and installation notes

    • Connection to the network must be made by a qualified electrician following the TN-S scheme (N and PE separate).
    • Install a suitably rated circuit breaker or fuses on the supply side.
    • Test the RCD with the TEST button before every working day.
    • Mount the board vertically with the sockets facing down so that water does not enter the plugs.
    • Do not use damaged cables or plugs; do not leave socket lids open.

    Quick selection guide

    230/400 V
    50 A
    3×CEE 16 A
    1×CEE 32 A
    4×Schuko
    4P RCD
    IP44
    TN-S
    Suitable when you need:
    • Temporary power for a site from a 3-phase network
    • Connecting 3-phase and single-phase equipment in one place
    • Ready earth leakage protection without assembling a board
    Check before use:
    • That the supply line is protected by a suitably rated circuit breaker
    • That the total equipment current does not exceed 50 A
    • That the equipment plugs match CEE 16 A / 32 A 5P
    Important reminder: A residual current device does not protect against overload and short circuit – these functions must be performed by a circuit breaker or fuse in the supply circuit.

    FAQ

    Can I connect a welder?
    Yes, if its plug is CEE 32 A or 16 A 5P and its current does not exceed the socket rating.
    What is the rated current of the board?
    50 A.
    Is the board suitable for outdoor use?
    Yes, it is IP44 and climatic version U1, but it must not be immersed in water.
    Which network system is it designed for?
    TN-S systems with separate N and PE conductors.
    Is there a circuit breaker for each socket?
    The supplier specification lists only a 4P RCD, so overcurrent protection must be on the supply side.
    How many Schuko sockets are there?
    Four Schuko 230 V sockets with earthing contact.

    Temporary construction site distribution board | 3×CEE 16 A 5P + 1×CEE 32 A 5P + 4×Schuko 230 V | 4P residual current device | 50 A | IP44 | 257×409×160 mm | IEK | 0020324

    IEK 0020324 – a temporary construction site distribution board with 3×CEE 16 A, 1×CEE 32 A and 4×Schuko sockets, a 4P RCD, 50 A rated current and an IP44 enclosure for safe power distribution on site.

    Published: 2026-11-15 · Data verified against the supplier specification: 2026-11-15

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Temporary construction site distribution board | 40 A | with circuit breakers and residual current device | 1×CEE 400 V + 2×CEE 230 V sockets | metal | surface-mounted | 410×300×180 mm | IP44 | SKLS40
    Code: SKLS40

    A 40 A metal surface-mounted construction site distribution board with installed circuit breakers, a residual current device and three industrial CEE sockets – one 3-phase 400 V (red) and two single-phase 230 V (blue). The enclosure has a door with a lock, IP44 protection.

    Price 163.35 € VAT incl.
    ( 135.00 € VAT excl. )
    Membrane cable entry grommet | for cable Ø12–18 mm | for TITAN 5 boards | grey | IP54 | IEK | YIS50-VS-K03
    Code: YIS50-VS-K03

    IEK YIS50-VS-K03 – a membrane cable entry grommet for one cable Ø12–18 mm, designed for IEK TITAN 5 board enclosures. Grey, polypropylene, operating temperature −40…+80 °C. Degree of protection IP54.

    Price 0.39 € VAT incl.
    ( 0.32 € VAT excl. )
    5P 16A socket | angled outlet | 3F+1F | 3P+N+E | 6h | 400V | IP44 | IZVZ-SHUKO
    Code: IZVZ-S1653

    Combined angled industrial-type socket outlet designed for both three-phase (3P+N+E) and single-phase (Schuko-type) power supply. This device allows convenient use of both connections in one location – an excellent solution for workshops, warehouses, or construction sites where both powerful three-phase equipment and household devices are needed. Thanks to its angled mounting and IP44 protection, the socket is suitable for both indoor and protected outdoor environments.

    Price 15.70 € VAT incl.
    ( 12.98 € VAT excl. )
    CYKY-L 5G10 | 5×10 mm² | Copper power cable | 450/750 V | black | 1 m | Lietkabelis
    Code: 91951013

    CYKY-L 5G10 (5×10 mm²) – 450/750 V copper power cable for three-phase 400 V circuits with neutral. Solid cores, PVC insulation and sheath, suitable indoors, outdoors and in the ground. AB Lietkabelis, price per 1 m.

    Price 8.67 € VAT incl.
    ( 7.17 € VAT excl. )
    Industrial modular socket panel | 2×CEE 32 A 5P 400 V + 4×Schuko 230 V | space for 11 modules of protection | IP54 | SEZ ROS11/x-22
    Code: 88754

    SEZ ROS11/x-22 – a sealed industrial panel with sockets (2×CEE 32 A 5P 400 V + 4×Schuko 230 V) and space for 11 modules of protective devices. Degree of protection: IP54, mounting – wall-mounted (surface).

    Price 62.00 € VAT incl.
    ( 51.24 € VAT excl. )
  • privacy policy

    Information