Products catalog

  • Modular memory impulse relay | AC/DC 12–240 V | 16 A | 1 CO | DIN 1 module | GEYA GRM8-01

    Code: ESGRM81

    An electronic impulse time relay with memory function, designed for the control and protection of electrical circuits. Due to low power consumption, a sealed design, and DIN rail mounting, this relay is widely used in residential, commercial, and industrial applications. The relay operates on an impulse (latching) principle – the state is retained even in the event of a power loss, making it a highly effective solution where stable, reliable, and energy-efficient control is required. 

  • Modular memory impulse relay | AC/DC 12–240 V | 16 A | 1 CO | DIN 1 module | GEYA GRM8-01

    Electronic impulse (latching) relay for controlling lighting and other loads from several locations with ordinary push-buttons. Each short pulse to control terminal S toggles the changeover contact to the opposite state. The memory function keeps the state after a power failure.

    Key idea:
    The wide supply range AC/DC 12–240 V lets you use the same relay in 12 V, 24 V or 230 V control circuits. Instead of two-way and intermediate switches – push-buttons in parallel and one 18 mm relay in the panel.
    Contacts
    1 CO, 16 A
    Supply
    AC/DC 12–240 V
    Function
    impulse + memory
    Mounting
    DIN, 1 module

    Operating principle

    Supply is connected to terminals A1-A2, momentary push-buttons in parallel between A1 and control terminal S. Minimum impulse length is 25 ms.

    Each press toggles the output: ON – OFF. The green LED shows supply, the red LED shows the output state.

    Memory function: during a power failure the relay switches off, and when voltage returns it restores its previous state.

    Why choose GRM8-01?
    Electronic control with memory, LED indication and support for illuminated push-buttons (up to 75 pcs) – convenient in staircases, corridors and commercial premises.

    Technical specifications

    Product type Electronic memory impulse (latching) relay
    Manufacturer / model GEYA GRM8-01 AC/DC 12–240 V
    Supply voltage (A1-A2) AC/DC 12–240 V, 50–60 Hz
    Burden AC 0.09–3 VA / DC 0.05–1.2 W
    Supply voltage tolerance −15 % / +10 %
    Control terminals A1-S
    Output contacts 1 CO (1 × SPDT), 16 A / AC1
    Switching voltage 250 V AC / 24 V DC
    Control impulse length min. 25 ms
    Reset time max. 200 ms
    Illuminated push-buttons allowed, up to 75 pcs (0.68 mA, 230 V AC)
    Mechanical life (cycles) 10 000 000
    Electrical life (cycles) 100 000 (AC1)
    Indication green LED – supply, red LED – output
    Operating temperature −20…+55 °C
    Storage temperature −35…+75 °C
    Degree of protection IP40 (front panel) / IP20 (terminals)
    Cable cross-section 1 × 2.5 mm² or 2 × 1.5 mm²
    Mounting DIN rail EN/IEC 60715, 1 module (18 mm)
    Standard EN 61810-1

    Main features

    • Impulse control – each press toggles the state
    • Control from many places – push-buttons in parallel
    • State memory – restores the previous state when voltage returns
    • LED indication – supply and output state
    • 1 CO 16 A – changeover contact for the load
    • 18 mm width – one DIN module

    Applications

    • Staircases and long corridors
    • Large rooms with several entrances
    • Offices, shops, warehouses
    • Detached houses and cottages
    • Low-voltage (12/24 V) control circuits
    • Automation panels and control cabinets

    Use by need

    For the installer.
    Simple wiring: push-buttons in parallel, load via the panel, state visible on the LED.
    For automation engineers.
    Impulse control with memory – handy in control and signalling circuits.
    For home or building owners.
    Lighting from several places, and the state recovers by itself after a power cut.

    Practical example

    A three-storey staircase: a push-button on each floor, all wired in parallel to A1-S. The staircase lighting is switched via the GRM8-01 contact. After a power cut and restoration the lighting returns to its previous state.

    Pros

    • Control from any number of places
    • State memory
    • LED indication
    • Illuminated push-buttons allowed (up to 75 pcs)
    • One DIN module

    Cons / limitations

    • No manual switch on the front
    • 16 A / AC1 – for large LED or motor loads use a contactor
    • No overload or short-circuit protection – a circuit breaker is required

    Safety and installation notes

    • Install only with the power disconnected; panel work must be done by a qualified electrician.
    • Protect supply and load circuits with a circuit breaker.
    • Use momentary (non-latching) push-buttons.
    • Do not exceed 16 A / AC1; leave a margin for LED groups with high inrush current or use a contactor.

    Quick selection guide

    1 CO, 16 A
    AC/DC 12–240 V
    memory
    DIN 1 module
    Suitable when you need to:
    • Control lighting from several places
    • Keep the state after a power failure
    • See the state in the panel (LED)
    Check before use:
    • Control voltage matches AC/DC 12–240 V
    • Load current does not exceed 16 A
    • Push-buttons are momentary (non-latching)
    Important reminder: GRM8-01 switches the load but is not a protective device – the circuit must be protected by a circuit breaker.

    FAQ

    How many push-buttons can be connected?
    Practically unlimited – they are connected in parallel.
    What happens after a power failure?
    The relay switches off and restores its previous state when voltage returns.
    Can illuminated push-buttons be used?
    Yes, up to 75 pcs (0.68 mA, 230 V AC).
    How much panel space does it take?
    One DIN module – 18 mm.

    Keywords

    impulse relay, memory relay, latching relay, step relay, AC/DC 12–240 V relay, 16A relay, 1 CO, lighting control from several places, GEYA GRM8-01, GRM8-01, DIN relay

    Modular memory impulse relay | AC/DC 12–240 V | 16 A | 1 CO | DIN 1 module | GEYA GRM8-01

    GEYA GRM8-01 – electronic memory impulse (latching) relay, supply AC/DC 12–240 V, 1 CO 16 A, 18 mm DIN, LED indication. Controls lighting and other loads from any number of locations.

    Published: 2026-11-19 · Data verified against the manufacturer datasheet: 2026-11-19

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Terminal clamp | electrical wire connector | universal | 2x0.2-4mm² | for all wire types | WAGO | 221-412 | 4050821808435
    Code: WAGO 221-412

    The WAGO 221-412 connector is one of the most popular and reliable electrical wire connection solutions in the world. It is designed for fast, safe, and professional connection of various types of copper conductors without the need for additional tools.

    Thanks to the patented CAGE CLAMP® technology and convenient orange levers, this connector allows quick connection of solid, stranded, and flexible conductors. The transparent housing enables visual inspection of the connection quality, while its compact dimensions allow easy installation in junction boxes, distribution boards, luminaires, and various automation equipment.

    The WAGO 221 series is widely used in residential, commercial, and industrial applications where reliable, standards-compliant, and long-lasting wire connections are required. 

    Price 0.30 € VAT incl.
    ( 0.25 € VAT excl. )
  • Subscribtion to new arrivals

    privacy policy

    Information