Emergency stop button | mushroom | latching | with enclosure | 1NC | Ø22 mm | Ui 660 V | Ith 10 A | Si&hel | LA38-11MZS/STOP
Code: LA38-11MZS/STOPPrice 6.32 € VAT incl.( 5.22 € VAT excl. )A safety component designed for emergency control in various electrical circuits. This emergency stop button is used both in household devices and industrial equipment, ensuring quick and reliable power disconnection in extreme situations.
The button is made of durable plastic and copper and features an SPST (Single Pole Single Throw) mechanical design, ensuring long service life – up to 100,000 operating cycles.
-
Emergency stop button | mushroom | latching | with enclosure | 1NC | Ø22 mm | Ui 660 V | Ith 10 A | Si&hel | LA38-11MZS/STOP
Red mushroom-head emergency stop (E-STOP) button for mounting in a Ø22 mm hole in a control panel, enclosure or push-button box. When pressed, the button latches and opens the normally closed (1NC) contact – the control circuit is broken, and the machine stops and stays stopped until the operator deliberately resets the button. Supplied with a push-button enclosure with a yellow lid and one Ø22 mm hole, so the button can be mounted directly at the machine without a separate panel.
Key point:
Emergency stopping must work on the circuit-break principle, which is why an NC contact is used: if a wire breaks or a terminal comes loose, the circuit behaves exactly as if the button had been pressed. Latching prevents the machine from restarting as soon as the button is released – restart is only possible after resetting the button and giving a new START command.Contact
1NC (normally closed)Supplied with
button + enclosure (1 × Ø22 mm)Operation
latching, manual resetUi / Ith
660 V AC / 10 AOperating principle
The button is mounted in a standard Ø22 mm hole and connected in series in the control circuit – usually the contactor coil circuit, a safety relay or an emergency input of a controller.
In the normal state the 1NC contact is closed and the circuit passes the signal. When the mushroom is pressed, the contact opens and the button mechanically latches in the pressed position.
The contactor or safety relay disconnects the machine's power supply. Until the button is reset, restarting is impossible – this protects against accidental start-up.
Why choose LA38-11MZS/STOP?
A simple, affordable, standard-size E-STOP element that fits most panels and push-button boxes with a Ø22 mm hole. An NC contact and latching are the two things emergency stopping needs first and foremost.Technical specifications
Product type Emergency stop (E-STOP) button Scope of delivery Button + push-button enclosure (yellow lid, grey base, 1 hole Ø22 mm) Manufacturer Si&hel Model / code LA38-11MZS/STOP (LA38 series) Head shape Mushroom, red Operation Latches when pressed, manual reset Contact configuration 1NC (normally closed) Rated insulation voltage Ui 660 V AC Conventional thermal current Ith 10 A Mounting hole Ø22 mm Materials Plastic, copper Mechanical life 100 000 cycles Illumination None Country of origin China Key functions
- 1NC contact – the emergency circuit works on the break principle; a broken wire stops the machine just like pressing the button.
- Latching when pressed – the machine does not restart when the button is released; the stop remains active.
- Manual reset – restart only by a deliberate operator action.
- Large red mushroom – easy to find and press with the palm, even with gloves on.
- Standard Ø22 mm hole – fits existing panels, no extra cutting or adapters needed.
- Mechanical operation – no power supply, electronics or programming needed.
Where is it used?
- Conveyor and transporter control panels
- Control panels of machine tools, presses and woodworking equipment
- Automation panels of pumping stations, ventilation systems and boiler rooms
- Packaging, dosing and food industry lines
- Agricultural equipment: grain conveyors, manure removal systems
- Push-button boxes next to machines where the stop must be reachable from the workplace
- Workshops and training benches
Use by need
Panel builder.
A standard Ø22 mm element that can be quickly fitted into a panel or box and wired into the contactor coil circuit.Maintenance electrician.
An affordable replacement for a faulty or cracked E-STOP button in an existing panel with a Ø22 mm hole.Farm or workshop owner.
A simple way to install a clearly visible emergency stop next to a conveyor or machine.Practical application
If a grain conveyor is controlled by a contactor with START/STOP buttons, the 1NC contact of LA38-11MZS/STOP is connected in series with the STOP button in the contactor coil circuit. Pressing the emergency button then de-energises the coil, the contactor disconnects the motor, and the conveyor will not restart until the button is reset and START is pressed.Pros
- NC contact – correct emergency circuit principle
- Latching and manual reset
- Standard Ø22 mm mounting hole
- Ui 660 V, Ith 10 A – suitable for typical control circuits
- Mechanical life 100 000 cycles
- Attractive price when replacing or fitting many points
Cons / limitations
- Only one NC contact – no additional NO signal to report status to a controller
- The manufacturer does not provide AC-15 / DC-13 load data or an IP rating – for projects where these are mandatory, choose a certified safety button
- Not intended for direct switching of a motor or other power load
- Enclosure IP rating not declared; button not illuminated
Safety and installation notes
- Install and wire only with the power disconnected and after verifying the absence of voltage.
- Connect into the control circuit (contactor coil, safety relay), not directly into the motor supply.
- Connect the NC contact in series with other STOP elements – no parallel bypasses.
- Install the button in a clearly visible and freely accessible place; do not obstruct it.
- After installation check: when pressed, the machine stops; after resetting the button it does not restart on its own.
- Design and testing of the emergency stop system must be carried out by a qualified electrician.
Quick selection guide
E-STOP mushroom + enclosure1NCØ22 mmLatchingUi 660 V | Ith 10 ASuitable when you need:- to replace a faulty E-STOP button in a Ø22 mm panel;
- to fit an emergency stop to a contactor-controlled machine;
- a simple, affordable solution without additional contacts.
Check before use:- whether the panel has a Ø22 mm hole;
- whether one NC contact is enough or you also need an NO signal for a controller;
- whether your project requires a certified safety button with a declared AC-15 rating and IP class.
Important reminder: the button alone is not a complete safety system – it does not replace a safety relay, contactor, machine risk assessment or a properly designed emergency stop circuit.FAQ
Why is an NC rather than an NO contact used for emergency stopping?
Because an NC circuit stops the machine not only when the button is pressed, but also if a wire breaks or a terminal comes loose.How is the button reset after pressing?
The button stays latched in the pressed position and is reset manually.Can it switch off a motor directly?
No, it is intended for the control circuit; the motor must be disconnected by a contactor or another power device.Does the button need a separate panel?
No, the enclosure is included and can be fixed directly at the machine; if needed, the button can also be fitted into a Ø22 mm panel hole.What do 660 V and 10 A mean?
660 V is the rated insulation voltage Ui and 10 A is the conventional thermal current Ith, not the permissible switching current for an inductive load.Can several emergency buttons be used in one circuit?
Yes, the NC contacts of several buttons are connected in series, and pressing any of them stops the machine.Emergency stop button LA38-11MZS/STOP | with enclosure | 1NC
Red mushroom-head E-STOP button with push-button enclosure, 1NC contact, latching and manual reset, designed for a Ø22 mm hole in control panels and enclosures. Ui 660 V, Ith 10 A, mechanical life 100 000 cycles – a simple solution for emergency stop control circuits of conveyors, machine tools and other equipment.
Published: 2026-11-11 · Data verified against supplier specification: 2026-11-11
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.This product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products
Crane control panel | with 4 buttons | 5A | 120–400V | IP54Code: BPU10-4Button control panels are designed for switching electrical control circuits of lifting mechanisms. The sealed IP54 enclosure is made of heat-resistant ABS plastic with built-in buttons. A protective gland is provided to seal the cable entry, and a sealing gasket is installed between the enclosure and the panel.
The buttons meet the "CE" standard requirements in terms of design and technical specifications.
The remote control panels have passed certification tests and have received serial production conformity certificates.
Available with 2, 4, or 6 buttons.
The housing is made of non-flammable ABS plastic.
The cable entry includes a protective gland that prevents moisture and dust from entering the housing.Price 20.57 € VAT incl.( 17.00 € VAT excl. )














