Products catalog

  • Modular contactor | 2P | 1NO+1NC | 25A | 230VAC | DIN | MCF3 | Promfactor Baltic | MCF32511230 | 4779040154702

    Code: MCF32511230
    Barcode: 4779040154702

    MCF3 25-11 – 1NO+1NC (one normally open, one normally closed contact) modular contactor for DIN rail with a ~230 V AC coil. Rated current 25 A (AC-7a), for motors 8.5 A (AC-7b), width 1 mod. (18 mm). Designed to remotely switch two circuits in opposition – switching one on while switching the other off at the same time.

  • Modular contactor | 2P | 1NO+1NC | 25A | 230VAC | DIN | MCF3 | Promfactor Baltic | MCF32511230 | 4779040154702

    MCF3 25-11 (MCF32511230) – 1NO+1NC (one normally open, one normally closed contact) modular contactor for DIN rail. Designed for remote on/off switching of two circuits in opposition – switching one on while switching the other off at the same time. Coil ~230 V AC, rated current 25 A (AC-7a), for motors – 8.5 A (AC-7b).

    Key point:
    When one appliance must switch off and another switch on from the same signal, you need NO and NC contacts in one device. The 1NO+1NC contactor does this in a single module: when the coil is energised, the NO contact closes and the NC contact opens.
    Current AC-7a (heating, lighting)
    25 A
    Current AC-7b (motors)
    8.5 A
    Coil voltage
    ~230 V AC
    Width in the board
    1 mod. (18 mm)

    Operating principle

    The contactor is mounted on the DIN rail in the distribution board, next to the circuit breaker (MCB) protecting the load. The power circuit is connected to the contact terminals and the control device to coil terminals A1–A2.

    When ~230 V AC is applied to the coil, the electromagnet pulls in the armature: NO contacts close and NC contacts open. When the control voltage is removed, a spring returns the contacts to their initial position. The mechanism operates quietly, so it is also suitable for residential premises.

    This way the control device (time relay, thermostat, photo relay, controller) switches only the small coil current, while the contactor carries the load current.

    Why choose the MCF3 25-11?
    One device does both switching on and switching off, so a priority or interlock circuit becomes simpler and more reliable.

    Technical specifications

    Product type Modular contactor (DIN rail mounting)
    Manufacturer Promfactor Baltic
    Series / model MCF3 25-11
    Code MCF32511230
    EAN 4779040154702
    Contacts 1NO+1NC
    Number of poles 2
    Rated current AC-7a / AC-1 25 A
    Rated current AC-7b (household motors) 8.5 A
    Power AC-7a, 230 V 5.2 kW
    Rated operational voltage (Ue) ~230/400 V
    Coil (control) voltage (Uc) ~230 V AC
    Insulation voltage (Ui) 500 V
    Impulse withstand voltage (Uimp) 4 kV
    Frequency 50/60 Hz
    Utilisation categories AC-1, AC-3, AC-7a, AC-7b
    Width 1 mod. (18 mm)
    Terminal wire cross-section 1–4 mm²
    Terminal tightening torque 0.8 Nm
    Endurance electrical 100,000 cycles / mechanical 1,000,000 cycles
    Operating time 0.05 s
    Degree of protection IP20
    Operating temperature -25…+55 °C
    Storage temperature -25…+70 °C
    Altitude up to 2000 m
    Mounting DIN rail TH35 (35 × 7.5 mm)
    Comb busbar connection not provided
    Auxiliary contacts can be added (MF/AX11 1NO+1NC)
    Standards IEC/EN 61095, IEC/EN 60947-4-1

    Key functions

    • Remote load control – the load is switched by a time relay, thermostat, photo relay or controller via coil A1–A2.
    • Protects the control device from load current – the timer or thermostat contact switches only the coil current.
    • Compact installation – on the DIN rail in the distribution board, 1 mod. (18 mm).
    • Quiet operation – suitable for residential premises and offices.
    • Auxiliary contact – an MF/AX11 (1NO+1NC) can be fitted to the MCF3 for a status signal or interlock.

    Where is it used?

    • Load priorities (e.g. the water heater is disconnected when an electric cooker or heating switches on)
    • Power limiter and load management circuits
    • Changeover of dual-mode equipment
    • Signalling and indication circuits ("on / off" status)
    • Switching lighting between two groups
    • Automation boards that need a simple interlock

    Use by customer need

    For homeowners.
    Avoids increasing the supply capacity: when one large load switches on, another is disconnected automatically.
    For electricians.
    NO and NC contacts in one device – no need to combine several relays.
    For automation engineers.
    A simple hardware interlock and status signal without extra modules.

    Practical application

    If the supply capacity is limited, a power limiter or controller energises the contactor coil when the priority load switches on. The NC contact then disconnects the water heater, while the NO contact can switch on an indicator. Once the priority load has finished, the water heater switches back on.

    Pros

    • The control device does not switch the load current – longer service life
    • Mounted on the DIN rail alongside circuit breakers
    • Quiet operation
    • AC-7a and AC-7b currents clearly stated
    • MF/AX11 auxiliary contact can be added

    Cons / limitations

    • Does not protect against overload or short circuit – a circuit breaker is mandatory
    • IP20 – dry distribution boards only
    • Not connectable with a comb busbar
    • AC-7b current (8.5 A) is considerably lower than AC-7a – for larger motors choose a standard AC-3 contactor with a thermal overload relay

    Safety and installation notes

    • A circuit breaker upstream of the contactor is mandatory, selected for the cable and the load. The contactor does not protect the circuit.
    • For motors, check the AC-7b current, not the AC-7a current given in the name; additionally protect the motor with a motor protection circuit breaker or thermal overload relay.
    • The coil voltage (~230 V AC) must match the control voltage – a different voltage will burn out the coil or the contactor will not switch on.
    • Terminal wire cross-section – 1–4 mm², tightening torque – 0.8 Nm.
    • When several contactors next to each other operate continuously (e.g. heating all night), leave a gap or fit a spacer – this reduces heating.
    • Installation and connection to the 230/400 V network must be carried out only by a qualified electrician with the power disconnected.

    Quick selection guide

    25 A AC-7a
    8.5 A AC-7b
    1NO+1NC
    ~230 V AC
    1 mod. (18 mm)
    Suitable when you need to:
    • switch one circuit on and another off with a single signal
    • build a load priority circuit
    • have a status signal without an extra contact
    Check before use:
    • the load type: for heating – AC-7a current, for motors – AC-7b current
    • the coil voltage and the control device output
    • space in the board and gaps between continuously operating contactors
    • the circuit breaker upstream of the contactor
    Important reminder: A contactor only switches the load on and off – it does not replace a circuit breaker, motor protection or a residual current device.

    FAQ

    Does the contactor protect against overload and short circuit?
    No – the circuit is protected by the circuit breaker installed upstream of the contactor.
    Can it control a pump or fan?
    Yes, if the motor operating current does not exceed 8.5 A (AC-7b); for larger motors choose a standard AC-3 contactor.
    How does the NC contact work?
    The NC contact is closed when the coil is de-energised and opens when the contactor switches on.
    How much space does it take in the board?
    1 mod. (18 mm).
    What can control it?
    A time relay, thermostat, photo relay, smart module or controller whose output suits a ~230 V AC coil.
    Can an auxiliary contact be added?
    Yes, the MF/AX11 (1NO+1NC) auxiliary contact fits the MCF3 series.

    Modular contactor | 2P | 1NO+1NC | 25A | 230VAC | DIN | MCF3 | Promfactor Baltic | MCF32511230 | 4779040154702

    MCF3 25-11 (MCF32511230) – 1NO+1NC (one normally open, one normally closed contact) modular contactor for DIN rail: 25 A (AC-7a), 8.5 A for motors (AC-7b), coil ~230 V AC. Intended for remote control of two circuits in opposition – switching one on while switching the other off at the same time in a distribution board.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Modular photo relay | twilight switch with external sensor | 16 A | 12–240 V AC/DC | 1–50,000 lx | 1CO | DIN | GanzKK | SOU-1/UNI
    Code: SOU-1/UNI

    DIN rail twilight switch with universal 12–240 V AC/DC supply and external sensor: 1–50,000 lx, 1CO 16 A AC1, 0–2 min delay, 1 module.

    Price 42.47 € VAT incl.
    ( 35.10 € VAT excl. )
    LED signal lamp | 22 mm | 230 V AC/DC | red | IP54 | compact | Promfactor Baltic | FPL230RD
    Code: FPL230RD

    Compact one-piece LED signal lamp for a Ø 22 mm hole, 230 V AC/DC. Connected with two terminals and takes little space behind the door.

    Price 1.49 € VAT incl.
    ( 1.23 € VAT excl. )
    Industrial modular socket panel | 2×CEE 16 A 5P 400 V + 1×CEE 32 A 5P 400 V + 2×Schuko 230 V | space for 11 modules of protection | IP44 | SEZ ROS11/x-14
    Code: ROS11/x-14 2x230V+2x16A+1x32A

    SEZ ROS11/x-14 – a sealed industrial panel with sockets (2×CEE 16 A 5P 400 V + 1×CEE 32 A 5P 400 V + 2×Schuko 230 V) and space for 11 modules of protective devices. Degree of protection: IP44, mounting – wall-mounted (surface).

    Price 62.90 € VAT incl.
    ( 51.99 € VAT excl. )
    Terminal | connector paste for contacts | reduces oxidation | 35.3g | WAGO | ALU PLUS | 249-130 | for connecting aluminium and copper wires
    Code: 4017332133890

    Contact paste designed to protect aluminum conductors from oxidation and ensure a reliable electrical connection. This special paste allows aluminum and copper conductors to be safely and efficiently connected within the same connector, making it particularly useful when renovating older electrical installations where aluminum wiring is commonly found.

    Aluminum naturally oxidizes, and the resulting oxide layer increases contact resistance, causes connection heating, and may become a source of electrical faults. By using WAGO ALU-PLUS, the oxidation layer is reduced, electrical conductivity is improved, and the service life of the connection is significantly extended. 

    Price 2.83 € VAT incl.
    ( 2.34 € VAT excl. )
    Marker cable ties | 2.5x110 mm | white | nylon PA66 | 100 pcs | 4772124000407
    Code: 4772124000407

    Marker cable ties (code 4772124000407) – white PA66 nylon cable ties, 2.5x110 mm, with an integrated marking plate, in a pack of 100 pcs. Designed to bundle wires, cables and tubing while labelling them at the same time: the circuit number, port name or other information is written on the plate, so one tie handles both fastening and identification.

    Price 2.42 € VAT incl.
    ( 2.00 € VAT excl. )
  • privacy policy

    Information