Single-phase voltage monitoring relay | 1F | U> 225–275 V | 1 C/O 8 A | DIN | ES-RS-MV11
Code: ES-RS-MV11Price 33.93 € VAT incl.( 28.04 € VAT excl. )The ES-RS-MV11 is a voltage monitoring relay with an output contact: it does not carry the load itself but switches a contact that controls a contactor coil, a signal or an automation input.
-
Single-phase voltage monitoring relay | 1F | U> 225–275 V | 1 C/O 8 A | DIN | ES-RS-MV11
The ES-RS-MV11 is a voltage monitoring relay with an output contact: it does not carry the load itself but switches a contact that controls a contactor coil, a signal or an automation input. When the monitored voltage leaves the set limits, the contact switches over and the controlled circuit is disconnected.
Key point:
A control relay is suitable where voltage must be monitored precisely and a contactor or alarm controlled – it disconnects high-power loads via a contactor.Contact
8 AVoltage limits
225–275 VNetwork / supply
A1–A2, 230 V AC, 50/60 HzFunctions
U> / U<, contactHow it works
The relay is supplied from the monitored circuit (depending on the model via terminals A1–A2) and measures the voltage continuously.
When the voltage leaves the set limits and the delay expires, the output contact switches over – the contactor or alarm is disconnected.
When the voltage returns to normal, the contact switches back and the circuit is reconnected.
Why choose the ES-RS-MV11?
Precise voltage monitoring with a contact – suitable for automation, contactors and alarms when the load exceeds the relay contact.Technical specifications
Product type Single-phase voltage monitoring relay (control type – with contact) Manufacturer / code ES-RS-MV11 Supply A1–A2, 230 V AC, 50/60 Hz Operating voltage range 150–275 V AC Overvoltage limit U> (factory) 225–275 V Hysteresis ±3 % Measuring principle / error True RMS, < 1 % Voltage trip delay 0.1–10 s Output contact 1 C/O Contact current AC1 8 A Contact current AC15 2 A Insulation voltage Ui 250 V Maximum protective fuse 5 A Width (DIN modules) 1 Degree of protection IP20 Electrical / mechanical life (cycles) 100 000 / 1 000 000 Operating temperature −25…+50 °C Mounting DIN 35 mm Main functions
- Output contact – controls a contactor, alarm or automation input.
- Overvoltage monitoring U> – reacts to excessive voltage.
Where is it used?
- Pump and fan control panels
- Contactor control circuits
- Automation and alarm panels
- Generator and backup supply panels
- Battery and DC system monitoring (AC/DC models)
Use by need
For the automation installer.
Precise voltage monitoring with a contact for the control circuit.For the electrician.
A compact relay to upgrade an existing board.For the equipment manufacturer.
A simple solution for machine and equipment protection.Practical use
In a pump panel the ES-RS-MV11 monitors the mains voltage and controls the contactor coil: at too low voltage the contactor disconnects the pump before the motor overheats.Pros
- Precise voltage monitoring
- Output contact for control
- Compact
- DIN mounting
Cons / limitations
- High-power loads must be connected via a contactor
- Does not protect against lightning surges
- Does not replace a circuit breaker
- The manufacturer does not publish a full datasheet – parameters per supplier specification
Safety and installation notes
- Install only after disconnecting the supply; work must be done by a qualified electrician.
- The contact current must not exceed the rated value – connect high-power loads via a contactor.
- Protect the control circuit with a fuse or circuit breaker.
- Check the supply voltage – a relay for another voltage will not work or will burn out.
Quick selection guide
1FU> 225–275 V1 C/O 8 ASuitable when you need:- to control a contactor according to voltage
- to monitor voltage in an automation panel
Check before use:- the supply voltage matches the relay
- contactor coil current ≤ contact current
Important reminder: the relay contact is intended for control, not for a high-power load.FAQ
Can the load be connected directly?
Only a small one – connect high-power loads via a contactor.What is the supply voltage?
See the technical table – a relay for another voltage will not work.Are the limits adjustable?
Yes – with knobs or buttons.Does it reset automatically?
Yes, when the voltage returns to normal.Does it protect against lightning?
No – an SPD is needed for that.Is it suitable for DC circuits?
Only AC/DC or DC models – see the supply voltage.Single-phase voltage monitoring relay | 1F | U> 225–275 V | 1 C/O 8 A | DIN | ES-RS-MV11
ES-RS-MV11 – precise voltage monitoring with an output contact for automation and contactor control.
Published: 2026-11-13 · Data verified against the supplier specification: 2026-11-13
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.This product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products
Electrical distribution | modular enclosure | box | distribution board | 36 modules (2x18) | 432x448x161mm | transparent door | waterproof | surface-mounted | plastic | IP65 | Legrand | PLEXO | 601986 | 3245066019864Code: 601986Hermetic electrical distribution enclosure designed for the safe installation of modular electrical devices in both indoor environments and more demanding outdoor or industrial conditions. This is a high-quality IP65 protection class electrical box adapted to protect automation, protection, and electrical distribution equipment from dust, moisture, water splashes, and mechanical impact.
Price 87.95 € VAT incl.( 72.69 € VAT excl. )


















