
Single-phase voltage relay | 1F | 63 A | U> 230–300 V | U< 140–210 V | DIN | Tomzn | TVPS1-63A
Code: TVPS1-63APrice 24.20 € VAT incl.( 20.00 € VAT excl. )The Tomzn TVPS1-63A is a single-phase digital voltage relay for DIN-rail mounting in a distribution board.
-
Single-phase voltage relay | 1F | 63 A | U> 230–300 V | U< 140–210 V | DIN | Tomzn | TVPS1-63A
The Tomzn TVPS1-63A is a single-phase digital voltage relay for DIN-rail mounting in a distribution board. The full load of the protected circuit passes through its contact, so it directly disconnects an apartment, a house circuit or a single appliance. When the voltage leaves the set limits, the relay disconnects the load and reconnects it once the voltage is back to normal.
Key point:
A broken neutral in a three-phase supply or a sustained over- or undervoltage is the most common cause of damage to expensive appliances. A power relay disconnects such voltage before boiler electronics, a fridge or a computer are harmed.Load current
63 AVoltage limits
U> 230–300 V · U< 140–210 VNetwork / supply
1F, 230 V ACFunctions
U> / U<, auto reconnectHow it works
The relay is installed after the main circuit breaker: phase and neutral to the input, the protected load to the output. A microcontroller continuously measures the mains voltage and shows it on the display.
When the voltage leaves the set U> / U< limits, the load is disconnected after the set delay.
When the parameters return to normal, the load is reconnected after the set delay. For compressors set a delay of at least 3 min.
Why choose the Tomzn TVPS1-63A?
One power relay protects all appliances connected after it against a broken neutral and voltage fluctuations, without an additional contactor.Technical specifications
Product type Single-phase digital voltage relay (power type – load through the relay) Manufacturer / code Tomzn / TVPS1-63A Network 1F, 230 V AC Rated current 63 A Overvoltage limit U> (factory) 230–300 V, OFF Recovery after overvoltage (factory) 225–295 V Voltage trip delay 0.1–30 s (0.5 s) Undervoltage limit U< (factory) 140–210 V (170 V), OFF Recovery delay (factory) 1–500 s (30 s) Switch-on delay (factory) 1–500 s (10 s) Own consumption < 2 W Switching life (cycles) 100 000 Mounting DIN 35 mm Main functions
- Power relay – the full load passes through the relay, no additional contactor needed.
- Over- and undervoltage protection – appliances are disconnected when the neutral breaks or the network fails.
- Digital display or indication – the status is visible at once.
Where is it used?
- Apartment and house supplies (after the main circuit breaker)
- Boiler and heat pump electronics
- Fridges, freezers, air conditioners
- Country houses with a weak network
- Offices, servers, security systems
- Rental properties and unattended sites
Use by need
For the home or apartment owner.
One device protects all appliances against a broken neutral and voltage surges.For the electrician.
Simple installation after the main circuit breaker, limits set with buttons.For the country house owner.
On a weak network the real voltage is visible and equipment does not cycle needlessly.Practical use
A house has a three-phase supply with single-phase equipment distributed among the phases. If the neutral contact burns out, the voltage on one phase rises to 300–380 V – the Tomzn TVPS1-63A disconnects the load before the boiler controller and power supplies burn out, and after the neutral is restored the equipment is switched on after the set delay.Pros
- Full load through the relay
- Adjustable limits and delays
- Automatic reconnection
- Compact DIN housing
Cons / limitations
- Does not protect against lightning and short surges – an SPD is needed
- Does not replace a circuit breaker or RCD
- Single-phase – a three-phase house needs a relay per phase
- IP20 – dry board only
- The manufacturer does not publish a full datasheet – parameters per supplier specification
Safety and installation notes
- Install only after disconnecting the supply and checking that no voltage is present; work must be done by a qualified electrician.
- Upstream – a circuit breaker with a current not higher than the relay's rated current.
- Do not swap phase and neutral.
- Install the surge protective device (SPD) before the relay.
- For compressors set a switch-on delay of at least 3 min.
Quick selection guide
1F63 AU> 230–300 VU< 140–210 VSuitable when you need:- to protect an apartment, house or circuit against a broken neutral
- to protect a boiler, fridge, electronics
- to see the mains voltage
Check before use:- main circuit breaker current ≤ 63 A
- whether a surge protective device (SPD) is installed
Important reminder: a voltage relay does not replace a surge protective device, a circuit breaker or an RCD.FAQ
Does the relay protect against lightning?
No – a surge protective device (SPD) protects against lightning impulses.What current should I choose?
The relay's rated current must be at least that of the upstream circuit breaker – the Tomzn TVPS1-63A suits a breaker up to 63 A.What switch-on delay should I set?
For compressors at least 3 min; 10–30 s is enough for electronics and lighting.Why does the relay trip often?
Most likely the limits are too narrow for a weak network – measure the mains voltage first.Is it suitable for a three-phase house?
Yes – a relay is installed on each phase supplying the protected equipment, or choose a three-phase relay.Does the relay replace an RCD?
No – only a residual current device (RCD) protects people from electric shock.Single-phase voltage relay | 1F | 63 A | U> 230–300 V | U< 140–210 V | DIN | Tomzn | TVPS1-63A
Tomzn TVPS1-63A – protection against a broken neutral, overvoltage and undervoltage for a single-phase circuit.
Published: 2026-11-13 · Data verified against the supplier specification: 2026-11-13
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.This product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products
Terminal clamp | electrical wire connector | universal | 2x0.2-4mm² | for all wire types | WAGO | 221-412 | 4050821808435Code: WAGO 221-412The WAGO 221-412 connector is one of the most popular and reliable electrical wire connection solutions in the world. It is designed for fast, safe, and professional connection of various types of copper conductors without the need for additional tools.
Thanks to the patented CAGE CLAMP® technology and convenient orange levers, this connector allows quick connection of solid, stranded, and flexible conductors. The transparent housing enables visual inspection of the connection quality, while its compact dimensions allow easy installation in junction boxes, distribution boards, luminaires, and various automation equipment.
The WAGO 221 series is widely used in residential, commercial, and industrial applications where reliable, standards-compliant, and long-lasting wire connections are required.
Price 0.30 € VAT incl.( 0.25 € VAT excl. )











