Products catalog

  • Automatic transfer switch ATS SaiLingsi SLQ1 | 4P | 1600 A | 400 V | single-phase monitoring | 2 inputs – 1 output

    Code: ES-SLQ1-1600A/4
    Price 1338.26 € VAT incl.
    ( 1106.00 € VAT excl. )
    Buy more, pay less
    10+ pcs.  – 936.78 € for pcs. -30%

    SaiLingsi SLQ1 4P 1600 A – automatic transfer switch with single-phase voltage monitoring and a common output. 400 V, AC-33iB, automatic return.

  • Automatic transfer switch ATS SaiLingsi SLQ1 | 4P | 1600 A | 400 V | single-phase monitoring | 2 inputs – 1 output

    SaiLingsi SLQ1 is a panel-mounted automatic transfer switch (ATS) for two sources: main (I) and backup (II). When the main supply fails, the load is automatically transferred to the backup and returned when the main supply is restored. 4P, 1600 A, 400 V, single-phase monitoring.

    Key point
    One unit with integrated controller, motor drive and I-0-II handle. The manufacturer states automatic return to the main source and a fire control input. Ui, Uimp, Icw and transfer time depend on the frame size.
    Poles / current
    4P / 1600 A
    Voltage monitoring
    1 phase (230 V)
    Transfer
    < 3–5 s (by frame)
    Terminals
    2 inputs – 1 output

    How it works

    The controller monitors the source voltage. When main source I fails (manufacturer threshold – voltage below 85 % Ue) and backup II is energised, the motor drive transfers the contacts to II. When I returns, the switch automatically goes back to I.

    A key switch selects automatic or manual mode. In manual mode positions I, 0 or II are selected with the handle; in position 0 both sources are disconnected. The handle can be padlocked.

    The manufacturer specifies a fire control input – the fire alarm signal is connected to it.

    Single-phase monitoring: the controller is supplied from and monitors 230 V (L–N). "2 inputs – 1 output" terminals: sources at the top, the load to one common output. The manufacturer describes this as easier wiring.

    Technical specifications

    Type Automatic transfer switch (ATS) with integrated controller
    Manufacturer, model SaiLingsi (Wenzhou) Electronics Co., Ltd – SLQ1-1600A/4
    Poles 4P
    Rated current 1600 A
    Operating voltage Ue AC 400 V, 50 Hz
    Control voltage AC 230 V
    Utilization category AC-33iB
    Class PC (manufacturer data)
    Insulation voltage Ui 500–800 V (by frame)
    Impulse voltage Uimp 6–8 kV (by frame; SLQ1-100 nameplate – 8 kV)
    Short-time withstand current Icw 5–16 kA (by frame)
    Transfer time < 3 s – 5 s (by frame)
    Voltage monitoring Single phase, L–N 230 V
    Terminal arrangement 2 inputs – 1 common output
    Mechanical durability 9000 cycles
    Voltage deviation threshold < 85 % Ue
    Control Auto / manual (key), I-0-II handle, lockable
    Additional functions Automatic return, fire control input
    Installation category / pollution degree II / 3
    Ambient temperature −5…+40 °C (24 h average ≤ +35 °C)
    Altitude up to 2000 m
    Standard GB/T 14048.11 (nameplate)
    Data source Manufacturer nameplate and SaiLingsi technical information
    ⚠ The brand on the device is SaiLingsi (Wenzhou) Electronics. The manufacturer gives Ui, Uimp, Icw and transfer time as frame ranges – check the exact value for this size on the device nameplate. The photos show SLQ1-100/4P – other sizes and 3P versions differ in appearance and dimensions.

    Functions

    • Automatic transfer I → II and automatic return II → I
    • I-0-II handle with position 0
    • Auto / manual key switch
    • Handle padlock
    • Fire control input
    • Integrated controller and motor drive

    Versions and nearest sizes

    Applications

    • Building incoming panels with a backup generator
    • Industrial, commercial and high-rise buildings
    • Transfer between two grid supplies
    • Sites requiring fire control

    Practical example

    Commercial building with a 1600 A supply and a diesel generator: grid to I, generator to II, load to the common output. The controller monitors one phase, so a phase monitoring relay is worth adding for three-phase loads.

    Advantages

    • Integrated controller – no separate automation needed
    • Automatic return to the main source
    • I-0-II handle and padlock for maintenance
    • Fire control input
    • 9000 mechanical cycles

    Points to note

    • Transfer takes up to 3–5 s (by frame)
    • No generator start control specified by manufacturer
    • Does not break short circuits – upstream protection required
    • Only one phase monitored

    ⚡ Safe installation

    • Installation must be carried out by a qualified electrician with both sources disconnected.
    • Install short-circuit and overload protection upstream of the ATS on both supplies.
    • Select cables or busbars for 1600 A and the terminal size.
    • Connect a generator to the building installation only through a transfer switch.
    ☝ Elsprendimai.eu recommends: ATS selection guide · Diagrams: 3P or 4P · Consultation

    How to choose

    Select a current not lower than the incoming protection current. For three-phase motors or sensitive loads choose three-phase monitoring. 4P – when N must also be switched with a generator.

    4P · 1600 A
    1 phase (230 V)
    2 inputs – 1 output
    AC-33iB · 400 V
    Suitable if:
    • the site is three-phase but single-phase monitoring is sufficient
    • a common output is required
    • incoming current up to 1600 A
    Check:
    • exact Ui, Uimp and Icw values on the nameplate
    • short-circuit current at the installation point
    • panel space – frame dimensions depend on current
    Important: An ATS is not a protective device – install short-circuit and overload protection separately. If in doubt, consult a qualified electrician.

    Frequently asked questions

    What does "single-phase monitoring" mean?
    The controller monitors only one phase (L–N 230 V). If another phase is lost, the switch may not detect it – in that case choose the three-phase monitoring version.
    Does the ATS start the generator?
    The manufacturer does not specify a generator start function for this model – the generator start is controlled by its own automation.
    How long does the transfer take?
    According to the manufacturer – from under 3 s to 5 s depending on the frame.
    Can it be switched manually?
    Yes, with manual mode selected by the key, the handle is turned to I, 0 or II.
    What does the fire control input do?
    The fire alarm signal is connected to it according to the product wiring diagram.
    Can you help with selection?
    Yes. Send us the incoming current, network type and generator power – we will help you choose.

    Automatic transfer switch ATS SaiLingsi SLQ1 | 4P | 1600 A | 400 V | single-phase monitoring | 2 inputs – 1 output

    SLQ1 4P with integrated controller, single-phase monitoring and a common output – reliable transfer between the building supply and a generator.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    U-FTP Cable | 6A CAT | 4x2x23 AWG | shielded | copper | UV resistant | outdoor use | black
    Code: KIF6AOUTS500

    The U/FTP cable is a high-quality four-pair data transmission cable designed for telecommunication, industrial, and outdoor network installations. This cable is 100% copper, ensuring maximum signal transmission efficiency and minimal signal attenuation.

    It is adapted for 10 Gigabit Ethernet (10GBASE-T) data transmission at speeds of up to 10,000 Mbps and provides high electromagnetic resistance, as each pair is shielded with aluminum foil. Thanks to the PE outer layer, the cable is resistant to moisture, UV radiation, and mechanical impact, making it ideal for outdoor installations. 

    Price 0.73 € VAT incl.
    ( 0.60 € VAT excl. )
    Network plug | RJ45 connector (8P8C) | for UTP CAT 6e cable | unshielded | through-plug | transparent
    Code: WT117

    This RJ45 Cat.6 UTP modular plug is a high-quality 8P8C unshielded network connector type, designed for Cat.6 UTP (Unshielded Twisted Pair) cables. The special straight-through design makes cable termination easier and more convenient, as the wires can be threaded through the plug, allowing a visual check of the wire arrangement before crimping the connector.

    Price 0.20 € VAT incl.
    ( 0.17 € VAT excl. )
    Solar PV cable | H1Z2Z2-K | 1x4 mm² | black | 1.5 kV DC | EN 50618 | Dca | IEMMEQU HAR
    Code: H1Z2Z2K

    The cable is designed for connecting photovoltaic (solar energy) systems and interconnecting solar modules. This cable offers excellent resistance to ultraviolet (UV) rays, ozone, atmospheric effects, and temperature fluctuations. A durable and flexible single-core copper cable with double insulation ensures long service life and safe use even in the most challenging outdoor conditions. Suitable for installation both indoors and outdoors.

    Price 0.98 € VAT incl.
    ( 0.81 € VAT excl. )
  • privacy policy

    Information