Products catalog

  • Power supply with relay for mirror heating mat control | 12 V DC | 36 W | 3 A | relay 1 A / 230 V AC | IP20 | ELSP-XMP-12V036W

    Code: ELSP-XMP-12V036W

    This compact 36W constant voltage power supply is specifically designed for mirrors with an integrated anti-fog heating pad. It features a built-in 1A/230VAC relay that enables automatic control of the heating pad activation. The device provides a stable 12V output, is suitable for use in various residential and commercial environments, is fully insulated (Class II), and includes protections against overload, short circuit, and overheating.

  • Power supply with relay for mirror heating mat control | 12 V DC | 36 W | 3 A | relay 1 A / 230 V AC | IP20 | ELSP-XMP-12V036W

    A slim 36 W constant-voltage power supply for mirrors with LED lighting and an anti-fog heating mat. A single 16.5 mm housing combines a 12 V DC output for lighting and electronics with a built-in 1 A / 230 V AC relay that switches the heating mat circuit. Insulation Class II, with overload, short-circuit and overtemperature protection.

    Key point:
    A mirror with lighting and heating normally needs two things: a 12 V supply for the LED strip and a separate module to switch the 230 V heating mat. This power supply combines both functions in one housing, so there are fewer components and fewer connections behind the mirror, and more free space. It matters most where installation depth is limited and the heating has to be controlled together with the mirror.
    Output
    12 V DC, 3 A, 36 W
    Heating relay
    1 A / 230 V AC
    Housing thickness
    16.5 mm (178 × 53.5 mm)
    Efficiency
    88 %, no-load < 0.5 W

    How it works

    The power supply is installed behind the mirror or in a cabinet recess and connected to the 100–240 V AC mains with the primary lead H03VVH2-F 2×0.75 mm². On the secondary side there is a 3×22AWG lead for the 12 V load: LED strip, touch or proximity switch and other mirror electronics.

    The switching converter keeps a constant 12 V DC over the full 0–3 A load range (tolerance ±2 %). The built-in relay switches the heating mat circuit up to 1 A at 230 V AC, so the mat needs no separate control module. Wiring follows the manufacturer's connection diagram.

    The result is one slim unit that powers the lighting and controls the anti-fog heating. On overload or short circuit the supply enters hiccup mode and recovers by itself once the fault is removed; on overheating it shuts down and restarts after cooling.

    What is the benefit of ELSP-XMP-12V036W?
    One device is installed behind the mirror instead of two (a power supply and a separate relay for the mat). The 16.5 mm thickness lets it hide even in slim-profile mirrors, and no-load consumption below 0.5 W matters for a device that stays connected to the mains all the time.

    Technical specifications

    Product type Constant-voltage power supply with built-in relay for a mirror heating mat
    Product code ELSP-XMP-12V036W
    Output voltage 12 V DC (constant, not adjustable), tolerance ±2 %
    Rated current / range 3 A / 0–3 A
    Power 36 W
    Voltage regulation ±0.5 % (line), ±2 % (load)
    Ripple and noise max. 250 mVp-p
    Start-up time 500 ms (230 V AC), 1000 ms (115 V AC)
    Relay max. 1 A / 230 V AC, for a mirror heating mat
    Input voltage / frequency 100–240 V AC / 47–63 Hz
    Input current 0.36 A (230 V AC), 0.7 A (115 V AC)
    Inrush current 40 A (230 V AC)
    Leakage current < 0.5 mA (240 V AC)
    Efficiency 88 %
    No-load consumption < 0.5 W
    Overload protection 110–130 %, hiccup mode, automatic recovery
    Short-circuit protection hiccup mode, automatic recovery
    Overtemperature protection automatic shutdown, recovers after cooling
    Insulation class II (double insulation)
    Insulation resistance input–output ≥ 50 MΩ (500 V DC)
    Dielectric strength input–output 3.6 kV AC
    Ingress protection IP20
    Operating temperature −40 … +40 °C (Tc max. 90 °C)
    Relative humidity 20–95 % RH, non-condensing
    Storage temperature −40 … +90 °C
    Dimensions 178 × 53.5 × 16.5 mm
    Weight 0.136 kg
    Primary lead H03VVH2-F 2×0.75 mm², length 90 ± 10 mm
    Secondary lead 3×22AWG, length 90 ± 10 mm
    Safety standards EN 61347-1, EN 61347-2-13
    EMC standards EN 55015 (emission), EN 61547 (immunity), EN 61000-3-2, EN 61000-3-3

    Main features

    • Constant 12 V DC voltage – the LED strip lights evenly, with no brightness variation as the load changes.
    • Built-in relay 1 A / 230 V AC – the heating mat is controlled without an extra module, with fewer connections behind the mirror.
    • Three-level protection – overload, short circuit and overheating do not damage the supply; it recovers by itself once the cause is removed.
    • Insulation Class II – no protective earth conductor is needed, which simplifies installation in the mirror frame.
    • 88 % efficiency – less heat in the enclosed space behind the mirror.
    • No-load < 0.5 W – a supply that is always connected to the mains uses almost no energy while the mirror is off.

    Where is it used?

    • Bathroom mirrors with LED lighting and an anti-fog heating mat
    • Mirrored bathroom cabinets with integrated lighting
    • Bathroom mirrors in hotels and apartments
    • Mirrors in spas, sports clubs and changing rooms
    • Illuminated mirrors in beauty salons and hairdressers
    • Retrofitting an existing mirror – replacing a failed supply or adding heating

    Use by need

    For mirror manufacturers.
    One standard unit for lighting and heating simplifies the bill of materials and shortens assembly time.
    For bathroom fitters.
    The 16.5 mm housing fits behind the mirror, and the short leads allow a tidy connection in a sealed junction box.
    For homeowners doing repairs.
    Suitable for replacing a failed mirror power supply when both the lighting and the anti-fog heating must be kept.

    Practical example

    If a bathroom mirror has about 2.5 m of 12 V LED strip (9.6 W/m, about 24 W in total), a touch switch and a 230 V heating mat, then this one power supply feeds the strip and the switch while its relay switches the mat. The load is about two thirds of the rated power, so there is a reserve, and only one unit and one junction box are installed behind the mirror.

    What else is needed for a mirror kit?

    The power supply is the centre of the kit, but it does not work alone. A complete mirror lighting and heating solution normally needs:

    Anti-fog heating mat
    230 V, IP54, e.g. 600 × 400 mm mat ELSP-DFG6040. The mat current must not exceed 1 A.
    Switch behind the mirror
    Touch switch-dimmer TD012B (12–24 V, 4 A) or IR proximity switch ELSP-XM319-IR5 (12/24 V DC, 5 A).
    12 V LED strip
    Total power up to 36 W; choose a sealed strip for a damp room.
    Sealed junction box
    Junction box ELSP-XM-OJ-3319 (IP44, 250 V, 17.5 A) – for joining the 230 V wires behind the mirror.

    Pros

    • Power supply and heating control in one housing
    • Slim 16.5 mm housing – fits behind the mirror
    • 88 % efficiency, no-load < 0.5 W
    • Overload, short-circuit and overtemperature protection with automatic recovery
    • Insulation Class II, 3.6 kV AC dielectric strength between input and output
    • Universal 100–240 V AC input

    Cons / limitations

    • Relay only up to 1 A / 230 V AC – a higher-current mat or several mats need a separate controller
    • IP20 – not protected against water, to be installed only where it is protected from splashes and condensation
    • Fixed 12 V output – not suitable for 24 V LED strips
    • Short leads (90 ± 10 mm) – wires have to be extended through a junction box
    • Operating temperature up to +40 °C – do not install in a tightly closed recess next to a heat source

    Safety and installation notes

    • Switch off the power before installation and make sure the circuit is dead.
    • Connection must be made by a qualified electrician, observing the bathroom zone requirements.
    • The supply is IP20 – install it behind the mirror or in a cabinet where no splashes reach it and no condensation collects.
    • The total 12 V load must not exceed 36 W (3 A); for continuous operation we recommend a reserve of about 20 %.
    • The heating mat current must not exceed 1 A – check the mat power before connecting.
    • Make 230 V connections in a bathroom inside a sealed junction box.
    • Do not cover the housing with heat-insulating materials – leave an air gap for cooling.
    • When several supplies are connected to one circuit, take the 40 A inrush current into account when selecting the circuit breaker.

    Quick selection guide

    12 V DC | 3 A | 36 W
    Relay 1 A / 230 V AC
    178 × 53.5 × 16.5 mm
    IP20 | Class II
    Suitable when you need to:
    • power a 12 V LED strip and mirror electronics up to 36 W;
    • control one heating mat up to 1 A / 230 V AC without a separate module;
    • fit the power supply into limited depth behind the mirror.
    Check before use:
    • the LED strip voltage (must be 12 V) and total power;
    • the heating mat power and current (no more than 1 A);
    • that the installation place is protected from splashes and condensation;
    • that the switch or controller wiring matches the power supply connection diagram.
    Important reminder: the power supply does not replace circuit protection – the circuit breaker and the residual current device in the bathroom circuit. It is not an LED dimmer: to dim the light, a separate 12 V dimmer or a touch switch with dimming is needed.

    Frequently asked questions

    What LED strip power can be connected?
    The total 12 V load can be up to 36 W (3 A), and for continuous operation it is advisable not to exceed about 29 W.
    Which heating mat can the relay control?
    The relay is intended for a load up to 1 A at 230 V AC, so the current of the specific mat must be checked before connecting.
    Can the power supply be installed in a bathroom?
    Yes, but only behind the mirror or in a cabinet where it is protected from splashes and condensation, because its ingress protection is IP20.
    Can the power supply dim the light?
    No, for dimming a separate 12 V dimmer or a touch switch with dimming is connected between the supply and the LED strip.
    What if the mat current is higher than 1 A?
    In that case the mat must be controlled through a separate higher-current controller or relay, and this supply used only for the 12 V load.
    What happens on a short circuit on the 12 V side?
    The supply enters hiccup protection mode and starts working again by itself once the fault is removed.

    Power supply with relay for mirror heating mat | 12 V DC | 36 W | ELSP-XMP-12V036W

    ELSP-XMP-12V036W is a slim 12 V DC 36 W power supply for mirror LED lighting with a built-in 1 A / 230 V AC relay for the anti-fog heating mat. Insulation Class II, 88 % efficiency, overload, short-circuit and overtemperature protection, compliance with EN 61347-1 and EN 61347-2-13.

    Published: 2026-11-09 · Data checked against the supplier specification: 2026-11-09

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Wireless control kit | actuator RFSA-61B and wall controller RFWB-40 | 866-916MHz | 230VAC | iNELS RF | RFSET-SW-F1
    Code: RFSET-SW-F1

    iNELS RF RFSET-SW-F1 is a wireless control kit: RFSA-61B actuator (230 V AC, 1 changeover contact 16 A AC1, 6 functions) and RFWB-40 wall controller (CR2032, about 5 years). RFIO2 communication up to 200 m, works without internet.

    Price 63.90 € VAT incl.
    ( 52.81 € VAT excl. )
    Flexible copper cable H05VV-F | 3G1.5 mm² | 300/500 V | round | white | 1 m | Lietkabelis
    Code: 92331501

    H05VV-F 3G1.5 mm² – AB Lietkabelis flexible round copper cable with class 5 conductors, PVC insulation and a white PVC sheath, 300/500 V. Sold by the metre.

    Cores: L, N, PE. Indicative current ≈ 16 A – for household appliances indoors.

    Price 1.04 € VAT incl.
    ( 0.86 € VAT excl. )
    Cable sheath and wire stripper 0.2–4.0 mm² | ErgoStrip KNIPEX
    Code: 169501SB

    KNIPEX high-quality, ergonomically designed wire and cable stripping tool for fast, precise, and safe work. This stripping knife is highly favored by professional electricians for its versatility, durability, and practical design. Suitable for removing insulation from both signal and power wires, as well as for installation, data, and coaxial cables.

    Perfectly suited for use on construction sites and in domestic installations, especially where wires need to be quickly and accurately prepared for connection in confined spaces. 

    Price 48.40 € VAT incl.
    ( 40.00 € VAT excl. )
    Smart lighting controller | dimmer | 150W LED / 200W | 100-240V | Wi-Fi | RF 433MHz | SONOFF | D1
    Code: SONOFF-D1

    SONOFF D1 is a smart Wi-Fi and RF 433 MHz lighting dimmer for dimmable LED lamps up to 150 W and incandescent lamps up to 200 W. Controlled with the eWeLink app, the RM433 remote and by voice. Installed in an EU / 86-type box.

    Price 17.40 € VAT incl.
    ( 14.38 € VAT excl. )
    Sealing protective mastic tape | 25x1x500mm | for sealing cable mechanical damage area | S1052-1-500
    Code: S 1052-1-500

    Specialized self-fusing sealing tape designed for protecting and sealing damaged areas on cables. Made from black thermoplastic, highly flowable mastic, this tape effectively shields cable insulation damage from moisture, corrosion, and dust. Used for emergency or preventive repair of electrical, telecommunication, and signal cables, especially suitable for outdoor and damp environments.

    Price 7.87 € VAT incl.
    ( 6.50 € VAT excl. )
  • Subscribtion to new arrivals

    privacy policy

    Information