Products catalog

  • Three-phase voltage and phase monitoring relay | 3F+N | phase sequence | asymmetry | 10 A | DIN | F&F | CKF-BR

    Code: CKF-BR

    The F&F CKF-BR is a three-phase network monitoring relay with an output contact for motors, pumps and automation panels.

  • Three-phase voltage and phase monitoring relay | 3F+N | phase sequence | asymmetry | 10 A | DIN | F&F | CKF-BR

    The F&F CKF-BR is a three-phase network monitoring relay with an output contact for motors, pumps and automation panels. It detects phase loss and other network faults – depending on the model also wrong phase sequence, asymmetry or voltage deviations.

    Key point:
    The biggest dangers for a three-phase motor are a lost phase, wrong phase sequence or high asymmetry – the motor overheats or runs backwards. A monitoring relay disconnects the motor via a contactor before it fails.
    Contact
    10 A
    Network / supply
    3 × 400/230 V + N
    Functions
    phase sequence, asymmetry

    How it works

    The relay is connected to phases L1, L2, L3 (and N, depending on the model) and monitors network parameters according to the selected rated voltage Un.

    When a fault is detected, the output contact switches over and disconnects the motor or other equipment via a contactor; short fluctuations are filtered by the delay.

    When the parameters return to normal, the contact automatically returns to the operating state.

    Why choose the F&F CKF-BR?
    A compact way to protect a three-phase motor or pump against phase loss and other network faults.

    Technical specifications

    Product type Three-phase voltage and phase monitoring relay (control type – with contact)
    Manufacturer / code F&F / CKF-BR
    Supply 3 × 400/230 V + N
    Phase asymmetry threshold adjustable
    Trip delay 4 s
    Output contact 1 NO/NC
    Contact current AC1 10 A
    Degree of protection IP20
    Mounting DIN 35 mm

    Main functions

    • Phase loss detection – the motor does not run on two phases.
    • Phase sequence monitoring – the motor is not started with swapped phases.
    • Asymmetry monitoring – reacts to unequal phase voltages.
    • Phase loss monitoring – disconnects when a phase is lost.

    Where is it used?

    • Three-phase motors with contactor
    • Borehole and drainage pumps
    • Compressors, fans, conveyors
    • Refrigeration equipment, refrigerated trucks
    • Agricultural and construction site equipment
    • Automation panels

    Use by need

    For the automation installer.
    Phase monitoring in the contactor control circuit.
    For a farm or workshop owner.
    The pump and compressor are protected against a lost phase.
    For the electrician.
    A compact relay for the motor panel.

    Practical use

    A borehole pump or compressor is controlled by a contactor. If one phase is lost or the phases are swapped after repairs, the F&F CKF-BR prevents the motor from running – the contactor is disconnected.

    Pros

    • Monitoring of phase loss and other faults
    • Compact
    • Suitable for contactor control
    • DIN mounting

    Cons / limitations

    • High-power loads must be connected via a contactor
    • Does not protect against lightning surges
    • Does not replace a motor protection circuit breaker

    Safety and installation notes

    • Install only after disconnecting the supply; work must be done by a qualified electrician.
    • Connect high-power loads only via a contactor.
    • Check the phase sequence before start-up.
    • Set the rated voltage Un according to the network.

    Quick selection guide

    3F+N
    phase sequence
    asymmetry
    10 A
    Suitable when you need:
    • to protect a three-phase motor or pump
    • to monitor phase sequence and phase loss
    Check before use:
    • the network voltage matches the relay's Un
    • contactor coil current ≤ contact current
    Important reminder: the relay does not replace a motor protection circuit breaker and a thermal overload relay.

    FAQ

    Can a motor be connected directly through the relay?
    No – via a contactor.
    Is a neutral needed?
    Depends on the model – see the technical table.
    What does it protect against?
    Phase loss and, depending on the model, wrong sequence, asymmetry or voltage deviations.
    Does it protect against lightning?
    No – an SPD is needed for that.
    Does it reset automatically?
    Yes, when the parameters return to normal.
    Does it replace a thermal overload relay?
    No.

    Three-phase voltage and phase monitoring relay | 3F+N | phase sequence | asymmetry | 10 A | DIN | F&F | CKF-BR

    F&F CKF-BR – protection of three-phase motors and pumps against phase loss and network faults.

    Published: 2026-11-13 · Data verified against the manufacturer's datasheet: 2026-11-13

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Electrical distribution | modular enclosure | box | distribution board | 36 modules (2x18) | 432x448x161mm | transparent door | waterproof | surface-mounted | plastic | IP65 | Legrand | PLEXO | 601986 | 3245066019864
    Code: 601986

    Hermetic electrical distribution enclosure designed for the safe installation of modular electrical devices in both indoor environments and more demanding outdoor or industrial conditions. This is a high-quality IP65 protection class electrical box adapted to protect automation, protection, and electrical distribution equipment from dust, moisture, water splashes, and mechanical impact. 

    Price 87.95 € VAT incl.
    ( 72.69 € VAT excl. )
  • privacy policy

    Information