Automatic transfer switch ATS TAXNELE TXATS | 2P | 63 A | PC class | DIN
Code: ES-TXATS-63-2PPrice 66.55 € VAT incl.( 55.00 € VAT excl. )Buy more, pay less10+ pcs. – 20.33 € for pcs. -69%TAXNELE TXATS 2P 63 A – automatic transfer switch for grid and generator. PC class, automatic and manual mode, DIN rail mounting.
-
Automatic transfer switch ATS TAXNELE TXATS | 2P | 63 A | PC class | DIN
TAXNELE TXATS is an automatic transfer switch (ATS) that transfers the load from the main supply (A) to a backup source (B) – usually a generator – when the main supply fails, and back when it returns. 2P, 63 A, DIN rail mounting.
Key point
The sources cannot be connected together: the contacts are either in position A or B, so the generator cannot back-feed the grid. The control circuit is supplied from L–N 220–240 V.Poles / current
2P / 63 AClass
PCTransfer
< 8 msControl
Auto / manualHow it works
When side A is energised, the load is supplied from A. When A fails and B is energised, the drive turns the contacts to B. When A returns, the switch automatically goes back to A – the main source always has priority.
The Manual / Auto switch selects the mode. The handle may only be turned in "Manual" mode – this is marked on the device. LEDs A and B show which source is connected.
Each side has control terminals (AR, AN / BR, BN) and passive NC–C–NO contacts that can send a status signal to a controller or alarm.
Technical specifications
Type Automatic transfer switch (ATS), PC class Manufacturer TAXNELE (Taixin Electric), series TXATS Poles 2P Rated current 63 A Operating voltage 220–240 V AC (L–N) Frequency 50/60 Hz Insulation voltage Ui AC 690 V Impulse voltage Uimp 8 kV ATSE class PC (IEC 60947-6-1) Transfer time < 8 ms – without supply interruption (PC class) Control Auto / Manual; handle in Manual mode only Additional terminals AR, AN / BR, BN – monitoring; NC–C–NO – passive contacts Mounting 35 mm DIN rail Standard IEC 60947-6-1 Data source Manufacturer nameplate and manufacturer technical information ⚠ The brand on the device is TAXNELE. The table lists only parameters stated by the manufacturer; parameters not provided by the manufacturer are not listed. Photos may show another current or pole version of the same series – check exact data on the device nameplate. Transfer time – manufacturer data for this ATS design.Functions
- Automatic transfer A → B and return B → A
- Priority to main source A
- Mechanical interlock – A and B are never connected together
- Manual operation with handle in Manual mode
- A and B indicators
- Passive NC–C–NO contacts for status signal
Other versions of the same series
- TAXNELE TXATS 3P 63 A
- TAXNELE TXATS 4P 63 A
- TAXNELE TXATS 4P 100 A
- TAXNELE TXATS 2P 125 A
- TAXNELE TXATS 4P 125 A
- 2P – single-phase circuit (L and N), 3P – three phases, 4P – three phases and N.
- If the main source is a solar inverter, choose TXATS-PV.
Applications
- Houses and homesteads with a backup generator
- Farms, workshops, small commercial sites
- Transfer between two grid supplies
- Pumping stations, heating and ventilation equipment
Practical example
Homestead with a single-phase 5 kW generator: grid to A, generator to B, load panel to the output. When the grid fails and the generator is started, the ATS transfers to B; when the grid returns – back to A. Circuit breakers are installed upstream of the ATS on both supplies.
Advantages
- PC class – transfer without supply interruption
- Ui 690 V, Uimp 8 kV
- Passive contacts for status signal
- DIN mounting
Points to note
- Control circuit – L–N 220–240 V; if all phases must be monitored, add a phase monitoring relay
- No generator start control
- Does not break short circuits – upstream protection required
⚡ Safe installation
- Installation must be carried out by a qualified electrician with both sources disconnected.
- Install short-circuit and overload protection upstream of the ATS on both supplies.
- Select cable cross-section for 63 A and the installation conditions.
- Connect a generator to the house installation only through a transfer switch – never through a socket outlet.
- Turn the handle only in "Manual" mode.
How to choose
First determine the number of poles from the network, then the current from the main incoming circuit breaker. The ATS rated current must not be lower than the incoming protection current.
2P · 63 A220–240 V AC (L–N)PC · IEC 60947-6-1< 8 msSuitable if:- you have a grid and a generator or two grid supplies
- incoming protection is not higher than 63 A
- transfer without interruption is required
Check:- number of poles (2P)
- that the L–N control voltage is 220–240 V
- protection upstream of the ATS
Important: A transfer switch is not a protective device (except CB class) – install short-circuit and overload protection separately. If in doubt, consult a qualified electrician.Frequently asked questions
Does this ATS start the generator?
No. The manufacturer does not specify a generator start function. Passive NC–C–NO contacts transmit status, but generator control requires the generator's own automation.Is it suitable for a solar inverter?
The TXATS-PV version is intended for an inverter and grid scheme. The standard TXATS is for grid and generator.Can it be switched manually?
Yes, with the switch in "Manual", the handle is turned to A or B.Why 4P rather than 3P?
4P also switches the N conductor – recommended when the generator has its own N–PE link and RCD protection is used.Can you help with selection?
Yes. Send us the network type, incoming protection and generator power – we will help you choose the right switch.Automatic transfer switch ATS TAXNELE TXATS | 2P | 63 A | PC class | DIN
PC class ATS for grid and generator: automatic return to the main source, manual operation and passive contacts. Suitable for houses, farms and small sites.
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.This product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products
Relay socket | Finder 55.32 / 55.34 | 10 A | 250 V | DIN 35 mm | Finder 94.04SPACode: 94.04SPAFinder 94.04SPA – socket for Finder 55.32 / 55.34 relays, mounted on DIN rail. Screw terminals; the relay can be replaced without disconnecting wires.
Price 3.03 € VAT incl.( 2.50 € VAT excl. )Network plug | RJ45 connector (8P8C) | for UTP CAT 6e cable | unshielded | through-plug | transparentCode: WT117This RJ45 Cat.6 UTP modular plug is a high-quality 8P8C unshielded network connector type, designed for Cat.6 UTP (Unshielded Twisted Pair) cables. The special straight-through design makes cable termination easier and more convenient, as the wires can be threaded through the plug, allowing a visual check of the wire arrangement before crimping the connector.
Price 0.20 € VAT incl.( 0.17 € VAT excl. )Interface relay | 2CO | 10 A | coil 24 V DC | plug-in | OMRON LY2N 24 V DCCode: LY2N 24VDCOMRON LY2N 24 V DC – interface relay with 2CO contacts (10 A) and 24 V DC coil. For control signal isolation, contact multiplication and control of contactor and valve coils in automation panels.
Price 6.05 € VAT incl.( 5.00 € VAT excl. )Interface relay | 2CO | 8 A | coil 24 V DC | plug-in / PCB | Finder 40.52.9.024.0000Code: 40.52.9.024.0000Finder 40.52.9.024.0000 – interface relay with 2CO contacts (8 A) and 24 V DC coil. For control signal isolation, contact multiplication and control of contactor and valve coils in automation panels.
Price 2.96 € VAT incl.( 2.45 € VAT excl. )U-FTP Cable | 6A CAT | 4x2x23 AWG | shielded | copper | UV resistant | outdoor use | blackCode: KIF6AOUTS500The U/FTP cable is a high-quality four-pair data transmission cable designed for telecommunication, industrial, and outdoor network installations. This cable is 100% copper, ensuring maximum signal transmission efficiency and minimal signal attenuation.
It is adapted for 10 Gigabit Ethernet (10GBASE-T) data transmission at speeds of up to 10,000 Mbps and provides high electromagnetic resistance, as each pair is shielded with aluminum foil. Thanks to the PE outer layer, the cable is resistant to moisture, UV radiation, and mechanical impact, making it ideal for outdoor installations.
Price 0.73 € VAT incl.( 0.60 € VAT excl. )Interface relay | 2CO | 8 A | coil 24 V DC | plug-in | Schneider Electric RSB2A080BDCode: RSB 2A080BDSchneider Electric RSB2A080BD – interface relay with 2CO contacts (8 A) and 24 V DC coil. For control signal isolation, contact multiplication and control of contactor and valve coils in automation panels.
Price 2.94 € VAT incl.( 2.43 € VAT excl. )





















