Digital thermostat-hygrostat | −20…+80 °C, 0–100 % RH | 2 relays 10 A | 12 V DC | STC-3028
Code: ES-STC-3028-12Price 22.11 € VAT incl.( 18.27 € VAT excl. )Dual digital controller: thermostat and hygrostat in one panel-mount housing, powered from 12 V DC. Two independent 10 A relays switch heating or cooling and humidifying or dehumidifying based on a T/RH probe on a 1 m cable.
-
Digital thermostat-hygrostat | −20…+80 °C, 0–100 % RH | 2 relays 10 A | 12 V DC | STC-3028
STC-3028 is a dual digital controller: thermostat and hygrostat in one housing. It measures temperature −20…+80 °C and relative humidity 0–100 % RH with an external probe on a 1 m cable. Two independent 10 A relays switch heating or cooling and humidifying or dehumidifying. Supply – 12 V DC, mounted in a 71×29 mm cut-out.
Key point:
One device with two displays replaces two controllers: temperature on top, humidity below. The mode is set with two values – switch-on and switch-off – with no complex menu. The 12 V DC version suits places that already have a SELV supply – control panels, battery or solar systems.Temperature
−20…+80 °CHumidity
0–100 % RHOutputs
2 relays × 10 ASupply
12 V DCHow it works
The controller fits a ≈71×29 mm cut-out in a panel door or control box and is connected to 12 V DC. The probe with a 1 m cable goes into the controlled space. The relay contacts are volt-free – you bring the load supply yourself.
Each channel has two values: switch-on and switch-off. If the switch-on temperature is lower than switch-off – heating; if higher – cooling. Humidity works the same way: humidifying or dehumidifying.
The relay closes at the switch-on point and opens at the switch-off point. The gap between them acts as hysteresis, so the load does not short-cycle.
Why choose STC-3028?
Two control channels in a ≈75×34.5×85 mm housing save space and wiring. Settings are kept after a power loss, and T and RH readings can be offset in 0.1 steps against a reference meter.Technical specifications
Product type Dual digital controller (thermostat + hygrostat), panel-mount Manufacturer / model Manufacturer not confirmed / STC-3028 Supply 12 V DC Own consumption < 3 W Temperature measuring range −20…+80 °C Humidity measuring range 0–100 % RH Temperature accuracy ±1 °C Humidity accuracy Not reliably declared – treat as indicative Outputs 2 independent relays (T and RH), volt-free contacts Relay contact rating 10 A / 220 V AC Control logic Switch-on and switch-off values: heating / cooling, humidifying / dehumidifying Calibration T and RH offset, 0.1 step Probe Combined T/RH, 1 m cable Display 2 LED displays (T and RH) Mounting Panel-mount, cut-out ≈71×29 mm Dimensions ≈75×34.5×85 mm Operating environment 0…+60 °C, non-condensing Weight ≈120 g Package contents Controller, T/RH probe with 1 m cable Main functions
- Dual control – temperature and humidity are regulated independently, each by its own relay.
- Heating or cooling – the mode follows the ratio of switch-on and switch-off values.
- Humidifying or dehumidifying – the same principle for the humidity channel.
- Freely set hysteresis – the gap between the limits protects the load from frequent switching.
- Reading calibration – T and RH offset in 0.1 steps.
- Settings memory – values are retained after a power loss.
How does it differ from similar products?
Plastim PHG02 (531) Mechanical DIN-rail hygrostat 10–90 % RH, 10 (5) A, no display and no temperature channel. STC-3028 is digital, controls T and RH and mounts in a cut-out. XH-W3005 (20484–20486) Humidity-only controller. STC-3028 adds a thermostat channel with its own relay. Sentera RCTH / RSTH (22724) Room T/RH transmitters and controllers with analogue outputs and Modbus RTU – for building automation. STC-3028 is stand-alone, with relays and no communication interface. Other STC-3028 variants Same functions, relays and probe – only the supply differs. This variant – 12 V DC; others: 110–220 V AC (21501), 24 V DC (21503). Where is it used?
- Incubators and hatching cabinets
- Mushroom growing rooms and small greenhouses
- Cellars, storage rooms, archives – dehumidifier control
- Drying and ageing chambers
- Terrariums and animal housing
- Small cold rooms – via a contactor
- Stand-alone 12 V DC systems – battery or solar-powered cabinets, vehicles
Use by need
For beginners.
Set two values per channel – switch-on and switch-off. Switch-on below switch-off means heating or humidifying.For experienced installers.
Contacts are volt-free: feed the load through a circuit breaker and connect a compressor, dehumidifier or large fan via a contactor.For engineers / designers.
The device is stand-alone – no communication interface and no alarm output. For data to a BMS or PLC choose a T/RH transmitter with 0–10 V or Modbus RTU.Practical use
In a cellar humidity rises to 75 % RH and in winter the temperature drops to +3 °C. Settings: temperature on 5 °C, off 8 °C (heating); humidity on 60 %, off 50 % (dehumidifying). A heater up to 10 A is wired via the relay, the dehumidifier via a contactor. Result – both parameters kept within limits by one device, without a PLC.Pros / advantages
- Thermostat and hygrostat in one housing
- Two independent 10 A relays
- Simple setup – switch-on and switch-off values
- T and RH reading calibration
- Own consumption < 3 W
- Compact housing, cut-out ≈71×29 mm
Cons / limitations
- Temperature accuracy ±1 °C – too coarse for precise process control.
- No communication interface or alarm output – for BMS integration choose Sentera transmitters (22724) or LEFOO LFH10 (11907).
- Not a DIN-rail housing – for inside the panel choose PHG02 (531).
- Inductive loads (compressor, dehumidifier, motor) need a contactor.
- Humidity accuracy is not reliably declared – use a calibrated sensor for critical processes.
Safety and installation notes
- ⚠ Power the controller from a SELV supply of 12 V DC; observe polarity as marked on the terminals.
- ⚠ The relay contacts may also switch 230 V loads – then wiring must be done by a qualified electrician with the supply isolated and the circuit protected by a circuit breaker.
- ⚠ Route 230 V and SELV cables separately so the low-voltage circuit never touches mains conductors.
- ⚠ Connect a compressor, dehumidifier or motor via a contactor – the relay drives only its coil.
- ⚠ Mount the controller in a dry place, 0…+60 °C, non-condensing; only the probe goes into the humid space.
Quick selection guide
−20…+80 °C / 0–100 % RH2 relays × 10 A12 V DCCut-out ≈71×29 mmSuitable when you need:- temperature and humidity control in one device
- stand-alone control without a PLC or network
- mounting in a panel door or control box
- a 12 V DC supply
Check before choosing:- load current and type – inductive loads need a contactor
- whether the 1 m probe cable is long enough
- whether ±1 °C accuracy is enough for the process
- supply variant: 110–220 V AC, 12 V DC or 24 V DC
Important reminder: STC-3028 is not a protective device and has no alarm output. For critical processes provide separate over-temperature or emergency protection.☝ Elsprendimai.eu recommends:- Humidity controller Taxnele XH-W3005 – XH-W3005 12 V – if you need humidity control only, at the same supply voltage.
- Plastim PHG02 – Plastim PHG02 – mechanical DIN-rail hygrostat when the controller must sit inside the panel.
- Contactors and relays – Contactors and relays – for a compressor, dehumidifier or larger heater.
- Temperature and humidity sensor selection guide – Temperature and humidity sensor selection guide – when to use a controller and when a transmitter.
FAQ
Does STC-3028 mount on a DIN rail?
No. It is a panel-mount device for a ≈71×29 mm cut-out. For inside the panel choose PHG02 (531) or mount the controller in the panel door.How do I select heating or cooling?
Set the switch-on value below switch-off for heating, above it for cooling. Humidity works the same way: humidifying or dehumidifying.Does the relay supply voltage to the load?
No. The contacts are volt-free – the load supply must be brought separately through the relay contact.Can I connect a dehumidifier or compressor directly?
We recommend a contactor. 10 A is the contact rating, while the inrush current of an inductive load is much higher.Is there RS485 or another communication interface?
No. For data transfer to a BMS choose Sentera T/RH transmitters with Modbus RTU.Can the readings be corrected?
Yes. Temperature and humidity are calibrated in 0.1 steps against a reference meter.Sources: STC-3028 user manual and supplier technical data (Phipps Electronics, RCS Components, Riverwood, Shtrol). Checked 2026-10-19.
STC-3028 thermostat-hygrostat 12 V DC
STC-3028 is a panel-mount dual temperature and humidity controller with two 10 A relays and a T/RH probe, powered from 12 V DC. It measures −20…+80 °C and 0–100 % RH and controls heating, cooling, humidifying and dehumidifying.
Published: 2026-10-19 · Data verified against the supplier's data: 2026-10-19
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.This product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products
IP surveillance camera | Turret | 4 MP | 2.8 mm | IR 30 m | WDR 120 dB | PoE | IP66 | Hikvision DS-2CD2345FWD-ICode: DS-2CD2345FWD-IHikvision DS-2CD2345FWD-I is a 4 MP (2688 × 1520) turret camera with a 1/2.5" sensor, 120 dB WDR and IR up to 30 m. Line-crossing, intrusion and unattended-object detection, H.265+, PoE 802.3af, microSD up to 128 GB, IP66.
Price 137.00 € VAT incl.( 113.22 € VAT excl. )












