
Industrial socket board with protection | 1×CEE 16 A 5P + 2×230 V | RCD 40 A 30 mA + C16 | 9 modules | IP44 | Famatel RW3957 | 3957.0432
Code: 3957.7 0432EPrice 117.00 € VAT incl.( 96.69 € VAT excl. )Famatel RW3957 3957.0432 is a fully equipped wall-mounted board with one three-phase CEE 16 A 5P socket and two SCHUKO 230 V sockets.
- Sockets: 1×CEE 16 A 5P 400 V + 2×SCHUKO 16 A
- Protection: RCD 40 A 4P 30 mA, C16/3, 2×C16/1
- IP rating: IP44 (enclosure IP65)
- Standard: EN 61439-1/-2/-4
-
Industrial socket board with protection | 1×CEE 16 A 5P + 2×230 V | RCD 40 A 30 mA + C16 | 9 modules | IP44 | Famatel RW3957 | 3957.0432
Famatel RW3957 3957.0432 is a fully equipped wall-mounted board with one three-phase CEE 16 A 5P socket and two SCHUKO 230 V sockets. A 40 A 4P 30 mA residual current device and circuit breakers for each socket group are already installed, so the board only needs to be mounted and connected to the supply cable.
Key idea:
This is not an empty enclosure but a ready distribution point: 30 mA personal protection and overload and short-circuit protection are already in place. The board complies with EN 61439-4, so it is suitable not only for workshops and garages but also for construction sites.Sockets
1×CEE 16 A 5P 400 V + 2×SCHUKO 16 AProtection
RCD 40 A 4P 30 mA, C16/3, 2×C16/1IP rating
IP44 (enclosure IP65)Standard
EN 61439-1/-2/-4How it works
The board is wall-mounted; the supply cable enters through an M25 gland and is connected to the incoming 40 A 4P 30 mA residual current device (Eaton HNC-40/4/003).
After the RCD, power is distributed through three circuit breakers: C16 3P for the three-phase CEE 16 A 5P socket and 2× C16 1P, one for each 230 V socket.
The result is personal protection against electric shock, overload and short-circuit protection of each line and three sockets for different loads – all in one box.
Why choose Famatel 3957.0432?
No need to buy, assemble and install protective devices separately – it saves time, and the sockets are protected by a 30 mA RCD from day one. A separate breaker for each 230 V socket means that if one socket is overloaded, the other stays on.Technical specifications
Product type Wall-mounted distribution board with socket outlets and protective devices Manufacturer / code Famatel Polska / 3957.0432 (RW3957 series) Socket outlets 1× CEE 16 A 5P (3P+N+PE) 400 V IP44; 2× SCHUKO 16 A 230 V IP54 Residual current device Eaton HNC-40/4/003 – 40 A, 4P, IΔn = 30 mA Circuit breakers Eaton HN-C16/3 (CEE socket); 2× HN-C16/1 (230 V sockets) Protection rating Board IP44; enclosure IP65; CEE sockets IP44; 230 V sockets IP54 Modules 9-module enclosure Dimensions 245 × 215 × 150 mm (H × W × D) Cable entry M25 Mounting Wall-mounted Enclosure material Thermoplastic, grey Standards EN IEC 61439-1, EN IEC 61439-2, EN 61439-4 Key functions
- 30 mA RCD – protects people against electric shock at all three sockets.
- Separate breakers per group – an overload on one line does not switch off the other sockets.
- Three-phase CEE 16 A 5P socket – for a compressor, machine tool or heater up to ~11 kVA.
- Two 230 V sockets – for power tools, floodlights, chargers.
- EN 61439-4 compliance – can be used for construction site power distribution.
- IP65 enclosure – devices protected against dust and water jets.
Where is it used?
- Garages and car service workshops
- Workshops and production areas
- Warehouses and industrial halls
- Construction sites
- Farm buildings and livestock barns
- Temporary workstations on site
- Technical rooms
Use by need
For garage owners.
A ready, safe connection point for a three-phase compressor and tools without assembling a separate board.For construction site managers.
An EN 61439-4 compliant board with 30 mA protection – suitable for site power distribution.For installers.
Reduces installation time: only the cable entry, connection and test measurements remain.Practical application
If a workshop needs to connect a three-phase 5.5 kW compressor and still have two sockets for hand tools, the board is mounted at the workstation and supplied with a 5×2.5 mm² or 5×4 mm² cable from a C16–C20 breaker in the main board – all three loads immediately have their own protection plus common 30 mA residual current protection.Advantages
- Fully equipped – 30 mA RCD and breakers already installed
- Separate breaker for each socket / group
- EN 61439-4 compliant (construction sites)
- IP65 enclosure, sockets IP44/IP54
- Compact, 245 × 215 × 150 mm
- Eaton devices
Limitations
- Only one three-phase socket, no CEE 32 A – for more powerful equipment choose the 3958 series
- Common RCD: a leakage switches off all sockets
- Limited space for additional devices
- RCD type selected by the manufacturer – equipment with frequency inverters may require a type B RCD
- Overall rating IP44 – not for wash-down areas
Safety and installation notes
- The supply protection in the upstream board must not exceed 40 A (RCD rated current); select the cable accordingly.
- The phase sequence of the three-phase CEE socket must be L1-L2-L3 clockwise.
- Check terminal tightness before energising – terminals may loosen during transport.
- Press the RCD test button “T” every 3–6 months to check the mechanism.
- Connection and commissioning tests must be carried out by a qualified electrician.
Quick selection guide
1×CEE 16 A 5P2×SCHUKO 230 VRCD 40 A 30 mAC16 breakersIP44 / IP65EN 61439-4Suitable when you need:- A ready-to-use three-phase + single-phase socket point with protection
- A construction site distribution point compliant with EN 61439-4
- Fast installation without assembling a board
Check before use:- Whether equipment with a frequency inverter requires a type B RCD
- Whether the supply line protection is ≤ 40 A
- Whether the terminals are tight after transport
Important reminder: the board does not replace supply line protection – the cable is protected against overload by the breaker in the main board.FAQ
What is the RCD sensitivity?
30 mA (Eaton HNC-40/4/003) – the sensitivity required for personal protection against electric shock.Can it be used on a construction site?
Yes, the manufacturer declares compliance with EN 61439-4 for construction site boards.How much power can be connected to the CEE 16 A socket?
A three-phase load of up to ~11 kVA, protected by a C16 3P breaker.Do I need to buy breakers separately?
No – the RCD and three breakers are already installed.Which supply cable should be used?
Usually 5×2.5–5×4 mm² Cu; the exact size depends on line protection, length and installation method.Is it suitable outdoors?
Under a canopy or on a façade (IP44) – yes; for wash-down areas choose a higher rating.Industrial socket board with protection | 1×CEE 16 A 5P + 2×230 V | RCD 40 A 30 mA + C16 | 9 modules | IP44 | Famatel RW3957 | 3957.0432
Famatel RW3957 3957.0432 – a fully equipped 9-module board with one CEE 16 A 5P and two SCHUKO 230 V sockets, RCD 40 A 30 mA and C16 breakers, IP44, compliant with EN 61439-4. A ready solution for garages, workshops and construction sites.
Published: 2026-10-30 · Data verified against supplier specification: 2026-10-30
Published: 2026-11-15 · Data verified against the manufacturer / supplier specification: 2026-11-15
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.ManufacturerThe IP protection class indicates the device's resistance to environmental factors.

The first digit indicates protection against dust and solid objects.
The second digit indicates protection against moisture.First digit values:
X — Untested;
0 — No protection;
1 — Protected against solid objects larger than 50 mm;
2 — Protected against solid objects larger than 12.5 mm;
3 — Protected against solid objects larger than 1 mm;
4 — Protected against solid objects larger than 1 mm;
5 — Dust protected;
6 — Totally dustproof.
Second digit values:X — Untested;
0 — No protection;
1 — Protected against vertically falling water drops;
2 — Protected against water drops falling at a 15º angle;
3 — Protected against rain falling at a 60º angle;
4 — Protected against water splashes;
5 — Protected against water jets;
6 — Protected against large amounts of water;
7 — Protected against short-term immersion in water up to 1 meter deep;
8 — Protected against long-term immersion in water up to 3 meters deep.This product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products
Single-cable membrane entry flange | for Ø86 mm hole | cable Ø55–70 mm | flange Ø123.1 mm | grey | IP67 | HT Hi Tech Polymers | HTX-1Code: Sandariklis HTX-1HTX-1 is a membrane entry flange for one thick power cable Ø55–70 mm. It fits a round Ø86 mm hole in the enclosure wall, flange diameter Ø123.1 mm. Sealing rating is IP67 according to the latest manufacturer's sheet.
Price 21.78 € VAT incl.( 18.00 € VAT excl. )Terminal | connector paste for contacts | reduces oxidation | 35.3g | WAGO | ALU PLUS | 249-130 | for connecting aluminium and copper wiresCode: 4017332133890Contact paste designed to protect aluminum conductors from oxidation and ensure a reliable electrical connection. This special paste allows aluminum and copper conductors to be safely and efficiently connected within the same connector, making it particularly useful when renovating older electrical installations where aluminum wiring is commonly found.
Aluminum naturally oxidizes, and the resulting oxide layer increases contact resistance, causes connection heating, and may become a source of electrical faults. By using WAGO ALU-PLUS, the oxidation layer is reduced, electrical conductivity is improved, and the service life of the connection is significantly extended.
Price 2.83 € VAT incl.( 2.34 € VAT excl. )Wire connector | universal electrical terminal | 5x0.2–4mm² | for all conductor types | WAGO | 221-415 | 4055143234658Code: WAGO 221-415WAGO 221-415 is a universal 5-conductor wire connector designed for fast and reliable connection of different conductor types. It is suitable for 0.2–4 mm² conductors, including solid, stranded and flexible wires. The transparent housing and lever design make wire insertion, inspection and reconnection easy.
Price 0.57 € VAT incl.( 0.47 € VAT excl. )Cable gland with locknut and gasket | PG7 | for cable Ø3–6.5 mm | grey | IP68 | 4772124000810Code: 00810Plastic PG7 cable gland with locknut and gasket for routing Ø3–6.5 mm round cables into distribution boards and junction boxes. Provides IP68 sealing when correctly installed.
Price 0.20 € VAT incl.( 0.17 € VAT excl. )















